Proficient C605 Manual


Læs gratis den danske manual til Proficient C605 (4 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Proficient C605, eller vil du spørge andre brugere om produktet?

Side 1/4
Before installing your LCR Ceiling Series speakers, you
should consider their placement carefully, taking into account
the location of electrical, plumbing and other xtures. Contact
your Dealer for assistance if you are unsure of the best
location for your particular listening environment.
Placement In Ceiling: When placing your speakers into the
ceiling, they should be located so that the fixed 1angle
woofer is pointed towards the primary listening area.
If the speakers are positioned far away from the primary
listening area, simply adjust the pivoting tweeters so they are
pointed towards it.
Note: To avoid possible damage to the pivoting tweeters, read
the section entitled “SPEAKER ADJUSTMENTS in this manual
prior to performing the tweeter adjustment.
In a very large room with low ceilings, it may be necessary to
place additional speakers throughout the room. Contact your
Proficient Audio Systems Dealer for assistance.
New Construction - Unfinished Ceilings
A Pre-Construction Bracket, available from your Dealer, may
be installed prior to drywall application across joists (up to 24"
on-center) where a speaker will be located. After the hole is
cut and the drywall is installed, the speakers are then easily
installed following the instructions for mounting in “Finished
Ceilings” below. If the speakers are to be mounted more Note:
than 24" on-center, a special Extra Long Wing” is available
from your Dealer.
Finished Ceilings
Prior to the actual installation of the speakers, it will be neces-
sary to run cables to the speaker locations. See your Dealer
for more information about cable installation. After the cable
has been properly installed, you are ready to mount the
speakers. Following the simple steps listed below will result in
a professional looking installation:
1. Determine the best area to mount your speakers. This area
of the ceiling should be free of obstructions such as electri-
cal conduit, HVAC ducts, or water lines. This can best be
determined by noting the placement of xtures and gaining
access to an attic or crawl space for further analysis of the
location of such obstacles.
2. Find the joists nearest the desired speaker mounting loca-
tion. We highly recommend using a good stud-finder tool
for this procedure. If you are lining up the speakers to some
other object or molding in the room, make sure you con-
sider the size of the baffle flange which extends beyond the
mounting hole.
3. Mark the hole. A template for setting the hole is provided
in the box (along with two paint mask inserts for use when
painting). Position the template in the desired position and
pencil an outline on the ceiling.
4. Cutting the hole. CAUTION: This is the most important
part of the entire installation. If you are not certain
whether any obstructions exist behind the desired mounting
area, you should start by cutting a small hole in the center
of your penciled mounting hole with a drywall saw, cutting
at a 45° angle towards the inside of the hole. (See Diagram 1)
Cutting the small hole at this angle will make drywall repair
much easier, using the piece cut out. Once you have deter-
mined that there aren’t any obstructions in your desired
mounting location, start cutting the finished hole at a 9
angle to the ceiling surface.
5. Add insulation. If the area in the ceiling is not already insu-
lated, add an adequate amount insulation material to loosely
cover the back of the speaker. If the insulation material used
is faced with foil or paper, position the foil or paper away
from the speaker.
SPEAKER PLACEMENT
MOUNTING SURFACE PREPARATION
Diagram 1:
Ceiling Cut Out
OWNER’S MANUAL
LCR CEILING SERIES
C870 C660 C650
The LCR Ceiling Series speakers come from the factory with
the tweeter facing straight out from the baffle. This will result
in the overall smoothest response. However, depending on
your particular primary listening area, room acoustics, ceiling
height, or personal preference, you may find the sound more
pleasing by pointing the tweeters in a particular direction. If
additional treble is desired in the primary listening area, point
the tweeter towards that area; and if less treble is required,
point the tweeter away. Push gently at the edge of the tweeter
to point it in the desired direction. (See Diagram 3)
CAUTION:
Avoid touching metal dome tweeters, as damage may
occur (C870 & C660).
The unique integral four-foot mounting system incorporated
into each LCR Ceiling Series speaker allows for a quick
installation by following these easy steps:
1. Remove the grille. It may be necessary to push one or two
of the mounting screws and its attached foot towards the
baffle and against the inside surface of the grille to force
the grille out of its retaining groove.
2. Attach the speaker cable (observing the proper polarity
with your amplifier, + to + and to ). Make sure the left
channel of the amplifier is connected to the left speaker,
the right channel is connected to the right speaker, etc.
3. Make sure the mounting feet are turned inward to clear the
opening, and insert the speaker into the ceiling. Position
the speaker into the hole.
Note: The flange of the speaker is designed to flex and
conform to any small imperfections in the ceilings sur-
face. Tighten the four screws on the front of the baffle only
enough to make the flange become snug against the ceiling.
As you tighten the screws, the feet will automatically flip into
an outward position (See Diagram 2), thereby clamping the
drywall between the feet and the flange. CAUTION: Over-
tightening may warp the bafe, crack the ceiling, cause
the flange to distort, and make the grille difficult to
install.
4. Push the grille firmly into the slot in the speaker baffle.
2
SPEAKER ADJUSTMENTS
SPEAKER INSTALLATION
Push Tweeter Here
Diagram 3:
Tweeter
Diagram 2:
Mounting Feet
Tweeter Adjustment :(C870 Only)
The switch labeled TREBLE allows for ±3dB of treble adjust-
ment. Your speakers were shipped with the treble switch in the
middle position, providing the most linear frequency response.
If you desire more treble, move the switch to the “+” position,
and the tweeter will play 3dB higher. If you desire less treble,
move the switch to the “– position, and the tweeter will play
3dB lower. To return to the neutral setting, push the switch
back to the middle position. (See Diagram 4)
Woofer Adjustment (C870 Only):
The switch labeled BASS allows for ±3dB of bass adjustment.
Your speakers were shipped with the bass set to the middle
position. This setting provides the flattest bass frequency
response. If you desire more bass, push the switch to the “+
position and the bass will play 3dB higher. If you desire less
bass, push the switch to the “–” position and the bass will play
3dB lower. This setting provides a more linear bass frequency
response. To return to the neutral setting, push the switch back
to the middle position. (See Diagram 4)
Bass Adjustment Switch
Treble Adjustment Switch
Diagram 4:
Adjustment Switches


Produkt Specifikationer

Mærke: Proficient
Kategori: Højttaler
Model: C605

Har du brug for hjælp?

Hvis du har brug for hjælp til Proficient C605 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Højttaler Proficient Manualer

Højttaler Manualer

Nyeste Højttaler Manualer