Pure Acoustics HT 770 Manual

Pure Acoustics Højttaler HT 770

Læs gratis den danske manual til Pure Acoustics HT 770 (5 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Pure Acoustics HT 770, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

IMPORTANT SAFETY NOTE:PROPER SELECTION OF MOUNTING

HARDWARE NOT INCLUDED HEREIN AND PROPER ASSEMBLY AND

INSTALLATION OF BRACKETS,INCLUDING BUT NOT LIMITED TO

SELECTION OF APPROPRIATE WEIGHT BEARING SUPPORT AND

BRACKET USE WITH THE SPECIFIED SPEAKER ONLY IS THE EXCLUSIVE

RESPONSIBILITY OF THE CUSTOMER MANUFACTURER DISCLAIMS ANY

LIABILITY FOR THE SELECTION OF MOUNTING HARDWARE AND OR

BRACKET INSTALLATION.

Bracket assembly and mounting:

Bracket

Bracket assembly

assembly

assembly and

and

and mounting:

mounting:

Loosen and remove the molded nut (2) by tuming it counter clockwise.Use

the supplied metal bar (5) if necessary by inserting it in one of the holes on

the molded nut (2).

Pull the ball/shaft (3) out of the wall bracket (4).b.

Slide on the molded nut (2) onto the ball/shaft (3) with threaded opening

facing the ball,and thread on the metal nut (1) all the way onto the ball/shaft

(3),with the nut (1)’s knuned surface facing away from the ball.” ”

Screw on the ball/shaft (3) into the threaded insert on the back of the speaker

cabinet (6) until it is fully seated aganst the bottom of the insert.

Tighten the knurted nut (1) using a crescent wrench until it is firmly seated

against the back of the speaker and has fully locked the ball/shaft (3) and the

speaker cabinet together.Please note that once this nut is tightened,it may

embed some marks on the back of the speaker where the attachment is

made.However these marks will be covered by the nut (1).

” ”

Mount the wall bracket (4) onto a wood stud on the wall,using#10,minimum

1 inch long,wood screws.Make sure that all 4 screws are driven into the stud

and not in drywall if the bracket needs to be mounted on drywall,the use of

properly selected and installed wall-anchors and screws is essential.

Holding the speaker cabinet (7) with both hands,reinsert the ball portion of

the ball/shaft (3) into the wall bracket (4).

Hand tighten the molded nut (2) while positioning the speaker for the intended

orientation. Please do NOT tighten the molded nut (2) too hard to avoid

damaging the bracket.

Once the orientation of the speaker is finalized,use the metal bar (5) in one

of the holes on the molded nut (2) and tighten securely . Please do NOT

press hard and strike the speaker when it is finalized.

Produkt Specifikationer

Mærke:	Pure Acoustics
Kategori:	Højttaler
Model:	HT 770
Bredde:	87 mm
Dybde:	112 mm
Højde:	87 mm
Produktfarve:	Hvid
Udgangseffekt (RMS):	120 W
Equalizer:	Ingen
Anbefalet brug:	Højttalersæt enhed
Frekvensområde:	65 - 200000 Hz
Impedens:	8 ohm (Ω)
Forbindelsesteknologi:	Ledningsført
Højttaler, type:	1-vejs
Lyd-output kanaler:	1.0 kanaler
Højttaler, placering:	Kan monteres på væggen
Antal drivere:	1
Diskanthøjttaler:	Ingen
Sensitivitet:	88 dB
Bashøjttaler:	Ingen
Forstærker:	Ingen
Mid-range driver diameter (britisk mål):	3 "