Pureheat Odyssey Eco OE35TW Manual

Pureheat Varmeapparat Odyssey Eco OE35TW

Læs gratis den danske manual til Pureheat Odyssey Eco OE35TW (2 sider) i kategorien Varmeapparat. Denne vejledning er vurderet som hjælpsom af 71 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 36 anmeldelser. Har du et spørgsmål om Pureheat Odyssey Eco OE35TW, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
WARRANTY
DR Distribution guarantees that any part*, which we find to be defective in
materials or workmanship will be repaired or replaced free of charge for the
parts and any service labour for a period of 24 months for residential use and 12
months for commercial use from the date of purchase, as the original purchaser
of a Pureheat product, provided that all service be pre authorised by DR
Distribution.
• *The heater warranty does not cover service calls related to over- temperature
safety devices activating and shutting the heater down.
• *This Warranty does not cover failure due to accidental damage, misuse or
negligence, nor does it cover any consequential damages.
Important: If you are experiencing difficulties with the operation
or believe that your Pureheat heater is faulty in any way,
contact D R Distribution on
02 9618 3842
For the purpose of this warranty, it is a condition that the “wired in” models must
be installed by a registered electrical contractor and must be wired in
accordance with our wiring instructions. Similarly, this warranty becomes void if
the heater is serviced, repaired or altered by anyone other than D.R. Distribution
or its authorised Service Agents or if parts, other than approved parts, have been
used.
Record the date of purchase below and retain this card, together with your
purchase invoice for your own future reference.
The benefits conferred by this warranty are in addition to all other rights and
remedies which the consumer has under the Trade Practices Act and other
legislation.
OE – Series 2.4kW, 3.5Kw, 4.5kw
INSTALLATION INSTRUCTIONS
IMPORTANT:
All Odyssey-Eco heaters are designed for wall mounting only and must not be used
for any portable application.
• Wiring must be carried out by an authorised electrician in accordance with all
relevant Australian and local wiring standards.
• Before obtaining access to terminals, all supply circuits must be disconnected.
OE24 MODELS – c/w Flex & Plug:
1. Refer Odyssey Template & Installation Instructions enclosed separately with the heater.
2. If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
3. The heater must not be located in front of a socket-outlet
OE35 MODELS and OE45 – Hardwired:
1. Remove both plastic side vents by unscrewing the two recessed screws on each side.
2. Remove front panel by undoing the 2 screws on either side of the heater.
3. Bring all electrical supply wiring through the cable entry at the top left hand side of
the rear face.
4. The heater should be mounted a minimum of 50mm (2”) above the top of the floor or
oor covering.
Notes:
• The heater must not be recessed and should have a clearance on either side
and above the heater of at least 200mm to allow for unobstructed airflow.
• When selecting a position for the heater care must be taken not to position
the heater close to curtains and other combustible materials.
• The heater must not be located immediately below a socket- outlet.
5. For the quietest operation, firmly screw the unit onto the wall at all four mounting pad
points located in the corners at the back of the heater.
6. Care must be taken when mounting heater on the wall that no twisting of the unit
occurs. It may be necessary to pack the rear panel with washers to overcome this.
7. The heater must be connected to a fixed, single phase 240 volts a.c. supply, through
an isolating switch and in accordance with the relevant local regulations.
Notes:
• All connections must be tight.
• Do not use this heater with an external programmer, timer or any other
device that switches the heater on automatically, since a fire risk exists if the
heater is covered or positioned incorrectly.
• The heater must not be located in front of a socket-outlet
8. Replace front cover and tighten screws.
9. Fit the two side panels supplied loose with the heater. (Do not over tighten and distort
front panel).
10. Test heater, ensuring all facets of the unit’s operation are fully functional.
NAME:
ADDRESS:
PURCHASED FROM:
DATE OF PURCHASE:
MODEL NO:
SERIAL
NO:
INSTALLED BY: DATE:
PUREHEAT
D R Distribution Pty Ltd
Unit 9 No 3 Lancaster St Ingleburn NSW 2565
Ph 02 9618 3842
www.drdistribution.com.au

Produkt Specifikationer

Mærke: Pureheat
Kategori: Varmeapparat
Model: Odyssey Eco OE35TW

Har du brug for hjælp?

Hvis du har brug for hjælp til Pureheat Odyssey Eco OE35TW stil et spørgsmål nedenfor, og andre brugere vil svare dig


Varmeapparat Pureheat Manualer

Pureheat

Pureheat Odyssey Eco OE24TW Manual

25 August 2024
Pureheat

Pureheat Odyssey Eco OE45TW Manual

24 August 2024
Pureheat

Pureheat Odyssey Eco OE35W Manual

24 August 2024
Pureheat

Pureheat Odyssey Eco OE35TW Manual

24 August 2024
Pureheat

Pureheat Odyssey Eco OE24W Manual

24 August 2024
Pureheat

Pureheat Odyssey Eco OE45W Manual

24 August 2024

Varmeapparat Manualer

Nyeste Varmeapparat Manualer

NEO Tools

NEO Tools 90-153 Manual

6 December 2025
Lasko

Lasko Stanley 675919 Manual

6 December 2025
Russell Hobbs

Russell Hobbs RHPANH2006B Manual

6 December 2025
Harvia

Harvia Qubic HBQ904E Manual

5 December 2025
Perel

Perel IH0004N Manual

5 December 2025
Harvia

Harvia Qubic Combi HBQ604SM Manual

5 December 2025
Bio

Bio Spectra 24 Manual

4 December 2025
Cecotec

Cecotec ReadyWarm 7200 Design Connected Manual

4 December 2025
Harvia

Harvia Qubic HBQ904 Manual

3 December 2025
Midea

Midea NDK20-21A Manual

3 December 2025