Pyle PDIC80T Manual

Pyle Højttaler PDIC80T

Læs gratis den danske manual til Pyle PDIC80T (1 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 11 anmeldelser. Har du et spørgsmål om Pyle PDIC80T, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

PWRC/PDIC/PWRC系列说明书/143x210mm/80克双铜/8页/需装订/新版

封面

SPEAKER CONNECTIONS

REAR SPEAKERS

IN-CEILING

CONNECTION TIPS

5-6FT

WALL WALL WALL WALL

LEFT RIGHT

Front or Rear Speaker Outputs

Proper placement of the speakers is an imporant step in obtaining

the most realistic soundstage possible.These recommendations are

for the optimum placement of the londspeakers.Use these placement

recommendations as a guide. Slight variations will not diminish your

listening pleasure.The front speakers should be placed the same di--

stance from each other as they are from the listening position.They

should be placed at about the same height from the floor as the liste-

ner’s ears will be,with the tweeters aimed toward the listener at ear-level height.In a home theater configu-

ration,the two surround,speakers should be placed slightly behind the listening position and ideally should

face each other and be at a level higher than the listener’s ears.If that is not possible,they may be placed in

a wall(or in the ceiling)behind the listening position,facing forword.The surround speakers should not call

attention to themselves.They should provide a diffuse,ambient sound accompanying the main program mat-

erial heard in the front speakers. In Dolby*Digital and DTS systems,aim the tweeters toward the listening

position at ear-level height.

The wires for both speakers

should be the same length.If

one speaker is placed closer to

the amplifer than the other,

hide the excess wire behid

the wall.Speakers and elec-

tronics terminals have corre-

sponding(+)and(-)terminals.

We use red to denote the(+)termi-

nal and black for the(-)termi-

nal.It is important to connect

both speakers identically:(+)on

the speaker to(+)on the ampli-

fier and(-)on the speaker to(-)

on the amplifier.Wireing“out

of phase” results in thin sound,

weak bass and a poor stereo

image.With the advent of multi-

channel surround sound

systems,connecting all of the

speakers in your system with

the correct polarity remains

equally important in order to

preserve the proper ambience

and directionality of the

program material.

INSTALLATION

WIRING DIAGRAM

(PDIC60T)

(PDIC80T)

TROUBLESHOOTING

IF THERE IS NO SOUND FROM ANY OF THE SPEAKERS:

IF THERE IS NO SOUND COMING FROM ONE SPEAKERS:

IF THERE IS LOW(OR NO)BASS OUTPUT:

IF THE SYSTEM PLAYS AT LOW VOLUMES BUT SHUTS OFF AS VOLUME IS INCREASED:

TOOLS NEEDED

The in-wall/in-ceiling speakers

were designed to be easily

installed.However,if you are

unsure of your ability to prop-

erly install these loudspeakers

please contact your dealer or a

quali fied installer.

Pencil Phillips #2 screwdriver

Measuring tape Utility knife

Carpenter’s level Awl

Check that receiver/amplifier is on and a source is playing.

Check all wires and connections between receiver/amplifier and speakers.Make sure all wires are connected.Make

sure none of the speaker wires are frayed,cut,punctured or tounching each other.

Review proper proper operation of your receiver/amplifier.

Check the Balance”control on your receiver/amplifier.“

Check allwires and connections between receiver/amplifier and speakers.Make sure all wires are connected.Make

sure none of the speaker wires are frayed,cut,punctured or tpunching each other.

Make sure the connections to the left and right“speaker Inputs”have the correct polarity(+ and -).

Consider adding a powered subwoofer to your system.

In Dolby Digital or DTS modes,make sure your receiver/processor is corectly configured.When using a subwoofer,

make sure thesubwoofer output of the receiver/processor has been enabled.If no subwoofer is being used,

make sure the left and right front and rear speakers have been configured as“LARGE”See your receiver/processor’s

owner’s manual for futher information on correct speaker configuration in Dolby Digital,DTS and other surround sound

modes.

Check all wires and connections between receiver/amplifier and speakers.Make sure all wires are connected.Make

sure none of the speaker wires are frayed,cut,punctured or touching each other.

If more than one pair of main speakers is being used,check the minimum-impedance requirements of your

receiver/amplifier.

Thank you for purchasing this PYLE in-wall/in-ceiling speaker system.It is a

state-of-the-art product carefully designed and manufactured for your installation

needs,and has been thoroughly tested to ensure consistent and reliable perfor-

mance.

If you have any question about the installation or operation of your PYLE

in-wall/in-ceiling speaker system which are not answered by this manual,contact

your dealer immediately.

INCLUDED

SPEAKER PLACEMNT

EXISTING CONSTRUCTION

IN-WALL SPEAKERS

EXISTING CONSTRUCTION

IN-CEILING SPEAKERS

IN-WALL SPEAKERS

IN-CEILING SPEAKERS

FRONT SPEAKERS

srtips of

adhesive

Template

One pair of speakers with grilles.

One pc of speakers with grilles

for PWRC52/PWRC62/PWRC82

One pair of speakers with grilles.

40 60

0 0

WALL

srtips of

adhesive

Screws Template

Φ4x12mm

12pcs

Cut the drywall.

Note:Always allow at least

one-half inch between a wall

stud and the speaker cutout or

the locking tabs will not be able

to swivel into place.

Cut the drywall.

Note:Always allow at least

one-half inch between a wall

stud and the speaker cutout or

the locking tabs will not be able

to swivel into place.

Put in the strips of adhesive to

secure the grille.

The in-wall speakers feature

unique swivel mounts for the

tweeters that enable you to aim

the very directional high frequencies

toword the listening position,

at ear-level height.

The in-ceiling speakers feature

unique swivel mounts for

the tweeters that enable you

to aim the very directional

high frequencies toword the

listening position,at ear-level

height.Before installing the

speaker grille,gently press on

the outer edge of the tweeter

mount to adjust the position of

the tweeter.The tweeter will

not swivel more than 15

degrees in any direction;do

not attempt to force it to move

further.

Screw down each of four

Phillips head screws.The

locking tabs will swivel into

place and secure the unit to

the rear surface of the daywall.

Put in the strips of adhesive to

secure the grille.

Before installing the speaker grille,

gently press on the outer edge of

the tweeter mount to adjust the

position of the tweeter.The

tweeter will not swivel more than

15 degrees in any direction;do not

attempt to force it to move further.

After installing the speaker grille,

gently press on the mesh of the

tweeter to adjust the position of

the tweeter.

After installing the speaker grille,

gently press on the mesh of the

tweeter to adjust the position of

the tweeter.

tweeter adjustment:

Just for PDIC60/PDIC80

PDIW55/PDIW65/PDIW57/PDIW67/PDIW87

PDIWS28/PDIWS8/PDIWS10/PDIWS12

PDIWCS56/PDIWCS62

PDIW52/PDIW62

Screw out the two

screws to seperate

the frame first.

Connect the speaker wiress to

the speaker.

Place the frame assembly

in the wall.

Screw down each of rhe six

Phillips head screws.The

locking tabs will swivel into

place and secure the unit to

the rear surface of the drywall.

Place the frame assembly

in the wall.

Connect the speaker wires

to the speaker.

Screw down each of the six

Phillips head screws.

Replace the metal grille.

Level

Template

Switch to “Transformer”

position when you connect

the speaker to 70V system

-Black

+Red

Speaker wires

to 8Ω amplifier

Speaker to “8Ω” position

when you connect the speaker to normal 8Ω amplifier

www.PyleUSA.com

70V SYSTEM

SPEAKER WIRES

70V SYSTEM

SPEAKER WIRES

PDIC80T

Blue

Red

Orange

Yellow

Brown

-Black(Negative)

10W

20W

30W

40W

50W

PDIC60T