Pyle PIC6E Manual

Pyle Højttaler PIC6E

Læs gratis den danske manual til Pyle PIC6E (1 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Pyle PIC6E, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/1
1.Introduction
The Pyle Home PIC6E/PIC8E both feature adjustable silk dome
tweeters and adjustable treble contro, allowing you
to select + 3dB, 0dB, -3dB adjustments. These
speakers are optimized for the demands of home
theater applications, and incorporate a 2 Way
speaker design, with a Poly Cone woofer made from
UFLC (Urethane Film Laminated Cloth). This set
includes paint rings and installation hardware, and
pre-construction installation, and pre-construction
installation brackets are also available seperately.
Disclaimer: Make sure you are in compliance with local building codes before
installing this speaker, These Pyle Home In-Ceiling Speakers are suitable for
moisture rich environments such as bathrooms or saunas, but not outdoor
applications.
INSTRUCTION &
INSTALLATION SHEET
PIC6E/PIC8E
In-Ceiling Speaker
INSTRUCTION &
INSTALLATION SHEET
PIC6E/PIC8E
In-Ceiling Speaker
2.Description
The PIC6E/PIC8E are made from a durable, semi-flexible plastic material that feature
built in foam gaskets to minimize vibration and maximize the installation seal. They
also feature a perforated metal grill with an acoustically transparent scrim cloth to
enhance the speakers appearance once installed. Pyle Home In-Ceiling speakers are
paintable, and well suited for moisture rich environments. They also feature flip out
tabs for easy installation and removal.
3.Installation
Installation of this PIC6E/PIC8E In-Ceiling speakers can be easily accomplished at multiple
stages of the construction process, whether it be “Rough In” (before drywall) or “Trim-Out”
(after drywall is Installed and painted)
A. “Rough-in” steps:
NOTE: It is recommended that a minimum of 16 gauge, 4
conductor wire be used for most applications from the amplifier or
volume control to this speaker. Different gauges can, and should,
be used based upon the distance of the intended run or quality of
installation(see Figure2).
www.pyleaudio.com
Speaker Wire
Gauge Selection Chart
Distance
<10 Feet
10-50 Fe et
>50 Feet
Gau ge
18
16
14
Figure 2
Figure 1
(shown with grill removed)
1.Run x/4 conductor (x=gauge preference) stranded speaker wire
from the distribution/volume control to the speaker location (pre-
wiring).
2.If PYLEAUDIO Speaker Pre-Construction Bracket is to be used,
skip to Step “5”.
3.If pre-wiring without using the PYLEAUDIO Pre-Construction
Speaker Brackets, leave 4 to 6 feet of wire at the speaker's
intended location. Use a strip of cardboard stapled to the
joints/studs with a hole through it as a wire place holder for the
drywall installers if installation of the speakers is intended ( see
Figure 3).
4.After drywall and/or painting is complete, push wire though hole,
center template over hole, mark with a pencil and cut out with a
drywall knife.
5 When using the PYLEAUDIO Pre-Construction Bracket (see .
figure 4), leave a coil of speaker wire on top of the bracket coiled
around the speaker mounting hole. There are clips on the corner of
the bracket to secure the speaker wire. Leave enough speaker wire
to be able to pull the wire through the speaker after the drywall is
installed. Strip off 3 inches or so of the speaker cable jacket to
expose the positive and negative insulate wires. Strip 3/8-1/2 inch
of insulation off of these conductors.
6 It is recommended to place insulation behind the speaker to .
provide some damping for the woofer driver. This will yield the best
po s s i b l e s o u nd . P Y LE AU DI O r e c o m m e n ds u s i ng p o l y -
encapsulated insulation such as Johns Manville Comfort Therm. If
a defined, consistent sound is desired to yield the ideal cubic
footage for the driver. Insulation would then be put in this space
during speaker installation .Refer to blocking chart for details.
7 If installing the speaker in a space with an attic above it is .
recommended that the speaker be boxed in with 1/2 inch MDF
(medium density fiber board) or plywood with insulation installed.
This will provide a defined acoustic space and protect the speaker.
The best possible sound will be achieved by doing this. Refer to
the blocking chart for details.
www.pyleaudio.com
NOTE: Make sure you are in compliance with local building codes before installing this
speaker in an attic space.
Figure 4
Figure 3
Plea se P ul l Thr u Dr y- Wall He re
Ins ul ati on
Bat ting
2 x 10 Joists
16” on Center
Blo ck ing
Dis ta nce
B. “Trim-out steps:
1 After drywall and/or painting is complete, push the speaker wire .
through hole, center template over hole, mark with a pencil and cut
out with a dry-wall knife.
2 Hold the speaker with one hand,(if speaker grill is off, pay careful .
attention to push on the woofer's cone, this can cause not
permanent distortion of the voice coil, thus producing a mechanical
rubbing sound or speaker failure),push in the speaker terminal
connectors and insert wires; remove speaker grill. Be sure to have
the positive wires in the RED terminals and the negative wires in
the BLACK terminals.
NOTE: Wiring both drivers of this speaker identically as the
above instruction states will yield a speaker whose drivers are
“in phase”. If one speaker driver is wired opposite of the other,
the speaker drivers will be “out of phase” with one another. If
the speaker drivers are “out of phase” the sound might appear
smeared (canned) and a significant loss of bass might be
noticeable due to phase cancellation. Make sure every
installed speaker is correctly phased.
3 Rotate the speaker driver towards the listening area and use one .
hand to push the speaker into the cut out (again, pay careful
attention to push on the woofer's cone this can cause not
permanent distortion of the voice coil, thus producing mechanical
rubbing sound or speaker failure) and the other to turn the screws
that engage the installation tabs (see ). Tighten the tabs in Figure5
a cross or X-pattern until “snug”. Be careful not to over tighten the
tabs or damage could result. The speaker should appear flush to
the surface.
NOTE: If using a cordless drill/screwdriver, it is suggested that
the screws be turned until almost tight, then finish tightening
via a hand screwdriver.
www.pyleaudio.com
NOTE:A strip of grill adhesive is provided to more securely attach the speaker grills on
final installation. Simply insert several short strips evenly around the grill slot prior to
installing the grill cover. Prior to final installation of the grill, adjust the tweeter for
optimum sound at the listening area.
6.5” Speak er (0.7 CuFt) Blocking Distance
16” on Center, 2x4
16” on Center, 2x6
16” on Center, 2x8
16” on Center, 2x10
16” on Center, 2x12
24” on Center, 2x4
24” on Center, 2x6
24.00”
15.25”
11.50”
9.00”
7.50”
15.50”
10.00”
8” Speak er (2.1 CuFt) Blocking Distanc e
16” on Center, 2x4
16” on Center, 2x6
16” on Center, 2x8
16” on Center, 2x10
16” on Center, 2x12
24” on Center, 2x4
24” on Center, 2x6
71.5”
45.50”
34.50”
27.00”
22.25”
46.00”
29.50”
PYLEAUDIO Speaker Blocking
Chart
Speaker
Specifications
Figure 5
Size/Type
Efficiency
Power(RMS/Peak)
Frequency Response
Woofer Type
Tweeter Type
Impedance
6.5” In-Ceiling 8” In-Ceiling
88dB 88dB
125W/250W 150W/300W
45-20KHz 35-20K
Polypropylene Polypropylene
UFLC Adjustable UFLC Adjustable
4-8 Ohm 4-8 Ohm
PIC6E PIC8E
INSTRUCTION &
INSTALLATION SHEET
PIC6E/PIC8E
In-Ceiling Speaker
3260100333,PIC6E/PIC8E通用说明书：A3纸，
105G铜版纸单色印刷说明书,A版

Produkt Specifikationer

Mærke: Pyle
Kategori: Højttaler
Model: PIC6E

Har du brug for hjælp?

Hvis du har brug for hjælp til Pyle PIC6E stil et spørgsmål nedenfor, og andre brugere vil svare dig


Højttaler Pyle Manualer

Pyle

Pyle PCB4BK Manual

4 September 2025
Pyle

Pyle PLMR24 Manual

4 September 2025
Pyle

Pyle PDWR50W Manual

30 August 2025
Pyle

Pyle PDWR42BBT Manual

29 August 2025
Pyle

Pyle PHSP131T Manual

29 August 2025
Pyle

Pyle PDWR42WBT Manual

29 August 2025
Pyle

Pyle PHSKR20 Manual

26 August 2025
Pyle

Pyle AZPWPS63BL Manual

9 August 2025
Pyle

Pyle PWRC52 Manual

9 August 2025
Pyle

Pyle PWMA1225BT Manual

9 August 2025

Højttaler Manualer

Nyeste Højttaler Manualer

DS18

DS18 GTX2 Manual

9 Januar 2026
DS18

DS18 PRO-HY69MSL Manual

9 Januar 2026
Devine

Devine Axeo 10A Manual

9 Januar 2026
DS18

DS18 NXL-LXY6 Manual

9 Januar 2026
DS18

DS18 PRO-CUPOLA3 Manual

9 Januar 2026
Ikea

Ikea KULGLASS 806.031.91 Manual

9 Januar 2026
DS18

DS18 NXL-LXY8 Manual

9 Januar 2026
DS18

DS18 PRO-HY69.4MSL Manual

8 Januar 2026
Denver

Denver BPS-457 Manual

8 Januar 2026
Devine

Devine Axeo 12A Manual

8 Januar 2026