Pyle PLUTV62CHK Manual

Pyle Modtager PLUTV62CHK

Læs gratis den danske manual til Pyle PLUTV62CHK (8 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 40 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 20.5 anmeldelser. Har du et spørgsmål om Pyle PLUTV62CHK, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

Questions? Issues?

We are here to help!

Phone: (1) 718-535-1800

Email: support@pyleusa.com

PRECAUTIONS

• This unit is designed for negative ground 12-14.50 Volts (DC) operation only.

• Use speakers with an impedance of 4 Ohms

• Avoid installing the unit where:

• It would be subject to high temperatures, such as from direct sunlight or hot air

from the heater.

• It would be exposed to rain or moisture.

• It would be subject to dust or dirt.

• If your vehicle or boat is parked in direct sunlight and there is a considerable

rise in temperature inside the car, allow the unit to cool oﬀ before operation.

• When installing the unit horizontally, be sure not to cover the heatsink ns with

the oor carpet.

• If this unit is placed too close to the resources radio, an interference may occur.

In this case, separate the amplier from the car radio.

• This power amplier employs a protection circuit to protect the transistors and

speakers if the amplier malfunctions. Do not attempt to test the protection

circuits by covering the heatsink or connecting improper loads.

• Do not use the unit with a weak auto battery as its optimum performance

depends on a normal battery supply voltage.

• For safety reasons, keep the volume of your audio system moderate so that you

can still hear normal traﬃc sounds in a reasonable distance.

WIRING INSTRUCTIONS

POWER CONNECTION

The battery terminal (BATT) must be connected directly to the positive terminal of

the vehicle battery to provide an adequate voltage source and minimize noise.

Connecting the battery terminal lead to any other point (such as the fuse block) will

reduce the power output and may cause noise and distortion. Use only #12 gauge or

thicker (smaller gauge #) wire for this lead and connect it to the terminal of the

battery after all other wiring is completed.

GROUND CONNECTION

The ground terminal (GND) connection is also critical to the correct operation of the

amplier. Use a wire of the same gauge as the power connection (#8 or thicker) and

connect it between the ground terminal (GND) of the amplier and a metal part of

the vehicle close to the mounting location. This wire should be as short as possible

and any paint or rust at the grounding point should be scraped away to provide a

clean metal surface to which the end of the ground wire can be screwed or bolted.

REMOTE TURN-ON CONNECTION

The amplier is turned on by applying +12V to the remote turn-on terminal (REM).

The wire lead to this terminal should be connected to the "Auto-Antenna" lead from

the vehicle/or boat stereo resources which will provide the +12V only when the

stereo resources is turned on. If the car stereo does not provide an "Auto-Antenna"

lead, the remote turn-on lead may be wired to an "Accessory" or "Radio" terminal in

the vehicle’s/or boat’s fuse block. This will turn the amplier on and oﬀ with the

ignition key, regardless of whether the stereo resources is on or oﬀ.

The remote turn-on lead does not carry large currents. So #16 gauge wire may be

used for this application.

SPEAKER CONNECTIONS

Depending on the type and number of speakers used with the amplier wire them

to the speaker terminals as per the appropriate wiring diagram. For most applications

#18 gauge wire should be used for the speaker leads but in no case thinner than

#16 gauge. For leads is excess of 10 feet #12 gauge is recommended. When wiring

the speakers, pay careful attention to the polarity of the terminals on the speakers

and make certain they correspond to the polarity of the corresponding terminals on

the amplier. Do not ground any speaker leads to the chassis of the vehicle/or boat.

OPERATION

After the amplier has been installed and all connections have been made carefully

and securely, turn the radio on so that the amplier is switched on automatically.

After a short power-on period, the amplier reaches its full performance. Now turn

up the volume slowly using the volume control of the radio. If there is no sound or

only a distorted replay, switch oﬀ the radio immediately - the amplier will also

switch oﬀ automatically - and check if all connections have been made correctly.

GND (-) = GROUND CONNECTION

Connect the GND terminal to the chassis ground of your vehicle/or boat and take

care of best electric and mechanic contact. In doing so, drill a hole into the vehicle/or

boat chassis near the amplier then remove color, dirt or any other substance from

the ground point. Thereafter fasten the cable end with added ring terminal by using

a screw. Ensure that the ground connection is as short as possible and that the cable

diameter is suﬃcient (min 4mm). Route the ground cables from the radio and all

other equipment parts, like equalizer, active crossover network or other ampliers, to

the same ground point.

www.PyleUSA.com

2www.PyleUSA.com 3

Produkt Specifikationer

Mærke:	Pyle
Kategori:	Modtager
Model:	PLUTV62CHK

Har du brug for hjælp?

Hvis du har brug for hjælp til Pyle PLUTV62CHK stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Modtager Pyle Manualer

Pyle PATVR10 Manual

3 Juni 2025

Pyle PFMRA340BB.5 Manual

13 Januar 2025

Pyle PLMRMBT5B Manual

6 December 2024

Pyle P3001AT Manual

6 December 2024

Pyle PTAU45.5 Manual

22 September 2024

Pyle PWMA3003BT Manual

20 September 2024

Pyle Pro PTAU23 Manual

6 September 2024

Pyle INV500DBA Manual

5 September 2024

Pyle PDA4BU Manual

3 September 2024

Pyle PD1000BA Manual

1 September 2024

Modtager Manualer

Nyeste Modtager Manualer

Planet Audio AC1200.2 Manual

15 Juni 2025

Planet Audio AC2400.4 Manual

15 Juni 2025

Planet Audio AC2600.2 Manual

15 Juni 2025

Planet Audio PL1500.1M Manual

15 Juni 2025

Ecler HSA2-400ES Manual

15 Juni 2025

Planet Audio PL4000.1D Manual

15 Juni 2025

Planet Audio MB1200.4D Manual

15 Juni 2025

Pure Acoustics AZ-2U-3240 Manual

15 Juni 2025

Ecler AURA-4B600 Manual

15 Juni 2025

Planet Audio TR3000.1D Manual

15 Juni 2025