Pyle PWD206 Manual

Pyle Alarmsystem PWD206

Læs gratis den danske manual til Pyle PWD206 (1 sider) i kategorien Alarmsystem. Denne vejledning er vurderet som hjælpsom af 34 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 17.5 anmeldelser. Har du et spørgsmål om Pyle PWD206, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/1
Overview
The PWD206 is a safety device using the most advance technologies of transponder chip that allow a user to
start his vehicle only after presenting a transponder tag to a hidden coil (loop antenna). The operation is fully
automatic and performance is 100% friendly.
Arming the System
To arm the system is fully automatic. The LED will flash rapidly after switching ignition off for 5 seconds.
The user will hear one (1) beep after 15 seconds, and the LED will flash slowly indicating the system is
arming.
Disarming the System
Switch ignition on (not start), the user presents his coded transponder tag to the hidden coil. If the
transponder code matched the code in the reader memory, the user will hear two (2) beeps and the LED will
flash twice, the system is disarming and will allow the user to start his vehicle.
If the user does not switch ignition on within 5 seconds, the LED will flash rapidly, and the system will auto
re-arm after 15 seconds.
User Transponder Tag Coding/Deleting (5 codes available)
1. Disarm the system and close the door.
2. Turn the ignition key to OFF/ON 5 times (OFF-ON, OFF-ON, OFF-ON, OFF-ON, OFF-ON), keep
ignition key at ON position.
3. ※Within 10 sec. hold 1st user tag to loop antenna area until LED flashes once and 1 beep. The system
will delete previously existed user tags from memory since new 1st user tag has been learned.
※ Within 10 sec. hold 2nd user tag to loop antenna area until LED flashes twice and 2 beeps.
※ Within 10 sec. hold 3rd user tag to loop antenna area until LED flashes three times and 3 beeps.
※ Within 10 sec. hold 4th user tag to loop antenna area until LED flashes four times and 4 beeps.
※ Within 10 sec. hold 5th user tag to loop antenna area until LED flashes five times and 5 beeps.
4. The system will exit programming/deleting mode immediately after programming the 5th user tag or
switching ignition off then on.
Test Searching Range
1. Disarm the system and close the door.
2. Turn the ignition key to OFF/ON 6 times (OFF-ON, OFF-ON, OFF-ON, OFF-ON, OFF-ON, OFF-ON),
keep ignition key at ON position.
3. Within 10 sec. present the tag to loop antenna.
※ LED will flash whenever tag reaches searching range.
※ The system will exit tag searching testing mode then enter auto arming if exceed 10 sec.
Override
Turning the ignition key to OFF/ON 8 times (OFF-ON, OFF-ON, OFF-ON, OFF-ON, OFF-ON, OFF-ON,
OFF-ON, OFF-ON) within 15 seconds, keep ignition key at ON position and hear one (1) beep. The system
is disarmed and you can turn the ignition key to start.
If you miss the OFF/ON sequences, turn ignition key to OFF and wait for 5 seconds, then repeat the
procedure.
07-08-357-1

Produkt Specifikationer

Mærke: Pyle
Kategori: Alarmsystem
Model: PWD206

Har du brug for hjælp?

Hvis du har brug for hjælp til Pyle PWD206 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Alarmsystem Pyle Manualer

Pyle

Pyle AZPLMCWD75 Manual

27 Juli 2024
Pyle

Pyle PWD206 Manual

24 Juli 2024
Pyle

Pyle PWD901 Manual

18 Juli 2024
Pyle

Pyle PWD501 Manual

1 Juni 2023

Alarmsystem Manualer

Nyeste Alarmsystem Manualer

Abus

Abus Smartvest Pro FUMK45000 Manual

29 Oktober 2025
B.E.G.

B.E.G. PD11-KNXs-FLAT-ST Manual

8 Oktober 2025
Hikvision

Hikvision DS-PD201MC-WB Manual

30 September 2025
Evolveo

Evolveo Alarmex Pro Manual

18 September 2025
Kemo

Kemo M062 Manual

18 September 2025
Velleman

Velleman K8093 Manual

17 September 2025
Smartwares

Smartwares FGA-13091 Manual

16 September 2025
Brandson

Brandson 304339 Manual

15 September 2025
Kidde

Kidde SM120X Manual

14 September 2025
Elektrobock

Elektrobock ELBO-073 Manual

14 September 2025