Pyle PWMA200 Manual

Pyle Højttaler PWMA200

Læs gratis den danske manual til Pyle PWMA200 (4 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 47 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 24 anmeldelser. Har du et spørgsmål om Pyle PWMA200, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Portable PA Speaker & Microphone System Kit

PWMA100 - AZPWMA100 - PWMA200

Questions? Issues?

We are here to help!

Phone: (1) 718-535-1800

Email: support@pyleusa.com

CAUTION

1. Keep this device away from high temperature. Don't expose this device to direct

sunshine or near the hot equipment.

2. Don't place the device in the environment of humidity and dirts.

3. Place the device in a ventilated environment.

4. Don't pull the power cord while unplug the device. Please hold he plug to unplug.

5. Unplug the device from mains power supply if you will not use the device for a

long time.

6. Your operation must be subjected to the specied voltage marked on the device

and complied with this manual.

7. Don't open chassis! It is very dangerous either open the chassis or put your hand

inside the chassis. If the device is not working properly, unplug the device at once

and contact your retailer or the nearest distributor.

PARTS DESCRIPTION

1. Power switch

2. Wireless volume control

3. RF indicator

4. Power indicator

5. Wired MIC volume control

6. Wired MIC input jack

7. Recording output jack

8. Treble control

9. Bass control

10. ECHO control

11. Charge indicator

12. DC input jack

13. Retractable antenna

14. Speaker

15. AC IN jack

OPERATION

1. POWER SUPPLY

a. AC power: Please conrm your current AC power is same as the voltage marked

on the device.

b. DC power: DC power can be input from DC IN jack. If you use car battery, the

power should be 12V-15V. Please note the correct polarity.

c. Built-in rechargeable battery: you can also use built-in rechargeable battery.

2. Turn on power switch of amplier, power indicator will light.

3. Open the battery cover of the transmitter. Put a 9V battery into battery compartment

and then close the battery cover. Keep transmitter at least 1M from the receiver to

prevent feedback. Turn on transmitter, RF indicator on receiver will light.

Adjust wireless microphone volume to suitable level. The wireless system is now

ready to use.

4. Wired MIC can connect to MIC in jack and its volume can be adjusted separately.

Wire microphone and wireless microphone can be used at the same time.

5. Adjust TREBLE/BASS to suitable level. When feed-back comes from amplier,

please reduce TREBLE. If feedback still exists, reduce the volume slightly.

6. REC OUT can connect to recorder player or external amplier.

RECHARGING

1. Connect amplier to AC power, charge indicator will light. The unit starts to charge

rechargeable battery. DC power can not charge the battery.

2. During charging you can use the unit at the same time.

3. When using rechargeable battery, if the unit stops producing sound, this means

the rechargeable battery power is low. Connect AC power to charge the battery.

Charging time is about 8~10 hours.

4. Please charge this device every 2 months if you don't use the device for a long

period of time.

5. Unplug th unit from mains power supply if you are not going to use this device for

a long time or after charging.

www.PyleUSA.com2www.PyleUSA.com 3

Produkt Specifikationer

Mærke:	Pyle
Kategori:	Højttaler
Model:	PWMA200
Type:	Scene/optræden mikrofon
Tænd-/slukkontakt:	Ja
Vekselstrømsindgangsspænding:	110 V
Vekselstrømsindgangsfrekvens:	60 Hz
Bredde:	180 mm
Dybde:	109 mm
Højde:	300 mm
Vægt:	4400 g
Produktfarve:	Sort
Strømforsyningstype:	DC
Forbindelsesteknologi:	Trådløs
Strømkilde:	DC
Effektkrav:	12 V, 1.2A
Mikrofonindgang:	Ja
Modtager inkluderet:	Ja
Driftsspænding:	12 V
Strømforbrug:	1200 mA
Driftsfrekvens:	160 - 270 Mhz
Maksimal driftstilstand:	30 m
Dybde (efter britisk standard):	4.3 "
Højde (efter britisk standard):	11.8 "
Bredde (efter britisk standard):	7.1 "