Qtx UV Cannon 160.028UK Manual

Qtx Lys UV Cannon 160.028UK

Læs gratis den danske manual til Qtx UV Cannon 160.028UK (3 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 74 personer og har en gennemsnitlig bedømmelse på 3.5 stjerner ud af 37.5 anmeldelser. Har du et spørgsmål om Qtx UV Cannon 160.028UK, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

1/1

400W BLACK LIGHT

160.028

USER MANUAL

INTRODUCTION

Congratulations on the purchase of your new our company lighting effect. We are confident you will enjoy

many trouble free hours with this unit . To assist with the care and use of the product we have prepared this

short guide.

OPERATION

Before connecting this unit to the mains power supply for the first time you must first install the lamp .

(See ‘Replacing Lamp’ for details).

This lighting effect has been designed to function on a mains power supply of either 240V~50Hz and has been

fitted with a suitable power plug for use with your local voltage. Check the label on the unit and the power plug

for the correct voltage.

When connected to the mains power supply the unit should illuminate. The 160.028 utilizes a mercury vapor

lamp ,it will take 5 to 10 minutes to reach full intensity . The intensity of the lamp will increase with use. The

light emitted by the 160.028 is invisible and does not have the glow of a fluorescent fixture.

Due to the high operating temperature of halogen lamps it is advisable that the effect be used in well ventilated

areas taking care not to obstruct the air vents. To maximize lamp life, allow the unit to cool down before

moving or touching the lamp.

CAUTION

Due to the nature of the mercury vapor lamp, this lamp must be allowed to cool down (about 5 to10 minutes)

after being turned off before re-igniting. Failure to wait for cool down many cause the lamp to fail prematurely.

INSTALLATION/MOUNTION

Although this unit can be used in an upright position , it is recommended that , for safety purposes ,your

lighting effect be properly mounted using a suitable hanging clamp and safety cable . Our company offers a

range of items , which are ideal for safe mounting .

Use in a well-ventilated area without obstruction to air vents.

2/2

REPLACING LAMPS

1. Disconnect from main power supply before attempting to replace either lamp .

2. Ensure that the unit is sufficiently cool , before removing blown lamps.

3. Never touch new lamps with your fingers: use a tissue or a cloth.

In order to replace the lamp, disconnect from main power supply rst, and unscrew the lamp replacement cover.

Only use the appropriately rated lamps as use of any other lamp type many cause the unit to be non-operational.

Due to the nature of halogen lamp it is vitally important that you do not touch the new replacement lamp with

your fingers, as this will reduce lamp life considerably. Once again a tissue or cloth can be used for fitting the

replacement lamp.

If after replacement of the lamp, the unit is still not working then please contact your dealer or our company for

servicing.

CLEANING

The most important part of your lighting effect to keep clean is the reflector as it allows the light output to

transmit. This should be cleaned with a soft damp cloth. The body of the unit may also be cleaned in the same

way . We recommend internal cleaning be carried out by a fully qualified technician.

MAINTENANCE & SERVICING

Work on internal parts should be carried out by a qualified technician. Removal of covers other than the front to

replace lamp is considered a breach of warranty and will not be covered under any such agreement unless

authorized first by the company.

TROUBLESHOOTING

• If the unit is not functional-check main power supply is ‘on’.

• If the unit is functional but lamp does not light-lamp may require replacing.

• If after trying this solution you still have a problem contact your dealer or our company for service.

CAUTION

Do not obstruct the air vents.

Do not touch unit or lamps while hot.

Never put any objects through the air grill on the top of the unit.

No user serviceable parts inside, please refer to our company.

POWER CONNECTIONS

The unit is supplied with a power plug appropriate to its voltage and destination. Should any other connections

be required they must be carried out with the following configuration.

Earth = Green/Yellow cable

Neutral = Blue cable

Live = Brown cable

Produkt Specifikationer

Mærke:	Qtx
Kategori:	Lys
Model:	UV Cannon 160.028UK

Har du brug for hjælp?

Hvis du har brug for hjælp til Qtx UV Cannon 160.028UK stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lys Qtx Manualer

30 Juli 2025

21 Maj 2024

2 Maj 2024

30 April 2024

11 Marts 2024

Qtx Wash & Beam Manual

30 Oktober 2023

11 Oktober 2023

26 August 2023

19 August 2023

17 August 2023

Lys Manualer

Nyeste Lys Manualer

Philips DN125B Manual

15 August 2025

Philips Ultinon Drive 5000 LUMUD5017LX1 Manual

15 August 2025

Philips Ultinon Drive 5100 LUMUD5102LX1 Manual

15 August 2025

Philips Ultinon Drive 7000 LUMUD7050LX1 Manual

15 August 2025

Honeywell HW-T12312 Manual

13 August 2025

V-TAC VT-10176 Manual

13 August 2025

Eurolite LED IP TMH-H420 Manual

13 August 2025

Eurolite LED Silent Par 6 QCL Floor Manual

13 August 2025

Neewer FS600C Manual

13 August 2025

Eurolite LED IP PAR 12x8W QCL Manual

13 August 2025