QualGear QG-SB-002-BLK Manual

QualGear Højtalerbeslag QG-SB-002-BLK

Læs gratis den danske manual til QualGear QG-SB-002-BLK (4 sider) i kategorien Højtalerbeslag. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om QualGear QG-SB-002-BLK, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Installing the Speaker onto the Mount

QG-SB-002-BLK

UNIVERSAL SPEAKER WALL MOUNT

Do not exceed the maximum rated weight

specied. Otherwise, serious injury or

property damage may occur.

.5kg

(7 7 bs)

3.5kg

(7.7lbs)

Vers on August

Speaker

Assemble the speaker bracket and speaker assembly with the

speaker mount by using the knob and at nut that was previously

removed from step 1.

Then insert the assembled

speaker mount with speaker

onto the wall plate. Secure it

by tightening the screw.

Speaker can be adjusted by

swiveling±70° left or right, and

by tilting ±20°up or down.

Speaker Bracket

Speaker Mount

Wall Plate

Scan the QR Code™ below

for more info about this product:

Version August 2020

Please read the entire installation manual before you start installation and assembly.

NOTE

W NGARNI

 This uct was d to be st d on the f g l struct n ly:prod designe in alle ollowin wal con io on

WALL CONST CTION DWARE REQUIREDRU HAR

W n tud Inc edoode S lud

W n B m Inc d oode ea lude

S d crete Inc d oli Con lude

Ot r ntact Q if d Profess alhe Co ual ie ion

 Do not begin to install your QualGear product

until you have read and understood all the

instructions and warnings contained in this

installation manual. If you have any questions

regarding the instructions, for US customers

please contact QualGear customer support

via email at support@qualgear.com. For

all international customers, please contact

your local distributor.

 T s hi produ houlct s d only be t d by ins alle

s e of omeon good mechanica ap ude hal tit , s

experience with basi buildinc g cons ruc iont t ,

and f y ull unders andt s t e hes ins ruc ionst t .

 T s hi product wa de ignes s d to be in allest d

and ut d y as s cif d in t s ilize onl pe ie hi manual.

I r mprope in alla iost t n of t s ct hi produ may c se au

damage or s s eriou injury. Q G r is t ual ea no

liable for e th improper use or in alla iost t n of its

products.

 Make sure t t the t g ha suppor in sur acf e

will sa elf y support the combine load d of the

equipment an ald

l a d ttache hardwar ane d

c ts.omponen

 A ys lwa use an assis ant t or mechanical

li inft g equipment to sa el lif y ft an posi iod t n the

equipment.

 Tighten screws rmly, but do not over tighten.

Over tightening can damage the items, greatly

reducing their holding power.

 ALL QUAL R ts GEA produc ar in endee t d for

indoor us onle y and an ou dooy t r use s the void

limi warranted ty.

 ALL QUAL R ts GEA produc ar designee d

and t ted for es re iden ias t l use onl any d any

commercial use v s the ted oid limi warranty.

For warranty information, please visit

http://www.qualgear.com/warranty.php.

 If g to mountin woode studn s, make sur thae t

moun int g sc s rew ar an horee c d into th cene ter

of the st s. Use of an t e stud ud edge- o-edg finder

is highl recommendedy .

 Never ex eec d the m maximu ra weighted t

speci ief d in t s .hi manual

 All bol ants d sc s rew must be used at the

designated points in the ins alla io ins ruct t n t tions

to preven propert ty damage and per ona/or s l

injury.

 DO NOT ins alt l nea air r condi ione ent r v ts or

where t e is her ex siv duces e st or s ke.mo

 W n he drilling holes in the wall, it is v y er

impor ant t to take c e of ar ele ri cablesct cal ,

water, or s ga pipes in the wall.

IMPORTANT! Please read the entire installation manual and check that all parts are

included before you start installation and assembly.

Part and Hardware Package

ST4.2x24mm

Lag Bolt (x4)

6x29mm Concrete

Anchor (x4)

M5x12 Screw (x4)

Disassembling the Speaker Wall Mount

Loosen and remove the screw in order

to separate the wall plate from the

speaker wall mount.

Loosen and remove the knob and the

at nut in order to separate the speaker

bracket from the speaker mount.

QG-S B-0 02- BLK

Marking Template (x1)

W-A W-B W-C

Wall Plate

Flat Nut

Knob

Produkt Specifikationer

Mærke:	QualGear
Kategori:	Højtalerbeslag
Model:	QG-SB-002-BLK

Har du brug for hjælp?

Hvis du har brug for hjælp til QualGear QG-SB-002-BLK stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Højtalerbeslag QualGear Manualer

QualGear QG-SB-001-BLK Manual

19 Juni 2025

QualGear QG-SB-002-BLK Manual

18 Juni 2025

Højtalerbeslag Manualer

Nyeste Højtalerbeslag Manualer

Sanus VMCC1 Manual

27 September 2025

Sanus XAS1A Manual

27 September 2025

Sanus VMA202 Manual

27 September 2025

Sanus WSSAFM1-B2 Manual

27 September 2025

B-Tech BT4002-SCC Manual

25 September 2025

Duronic DM454 Manual

24 September 2025

Sanus MFSBM1-B1 Manual

15 September 2025

QSC E15YM Manual

11 September 2025

Adam Hall SUWMB10W Manual

11 September 2025

Vivolink VLMSP-E300B Manual

9 September 2025