Qubino ZMNHBA2 power relay Manual

Qubino Ikke kategoriseret ZMNHBA2 power relay

Læs gratis den danske manual til Qubino ZMNHBA2 power relay (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Qubino ZMNHBA2 power relay, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Qubino

The INNOVATIVE SMALLEST and

Flush 2 relays

ORDERING CODE

Z-WAVE FREQUENCY

ZMNHBA2

868,4 MHz

ZMNHBA3

921,4 MHz

ZMNHBA4

908,4 MHz

ZMNHBA5

869,0 MHz

ZMNHBA6

916,0 MHz

This Z-Wave module is used for switching on or

oﬀ two electrical devices (e.g. lights, fans, etc ...).

The module can be controlled either through

Z-Wave network or through the wall switches.

The module is designed to be mounted inside a

“ ”ﬂush mounting box , hidden behind a traditional

wall switch.

Module measures power consumption of two

electrical devices and supports connection of

digital temperature sensor. It is designed to act

as repeater in order to improve range and

stability of Z-wave network.

Supported switches

Module supports switches (push mono-stable

button) and switches. The module is bi-stable

factory set to operate with bi-stable switches.

Installation

 Before the installation disconnect power

supply.

 Connect the module according to electrical

diagram.

 Locate the antenna far from metal elements

(as far as possible).

 Do not shorten the antenna.

Danger of electrocution!

 Module installation requires a great degree of

skill and may be performed only by a qualiﬁed

and licensed electrician.

 Even when the module is turned oﬀ, voltage

may be present on its terminals. Any works

on conﬁguration changes related to

connection mode or load must be always

performed by disconnected power supply

(disable the fuse).

Note!

Do not connect the module to loads exceeding

recommended values. Connect the module only

in accordance to the below diagrams. Improper

connections may be dangerous.

Package contents

 Flush 2 relays

Electrical diagram 230VAC

Notes for the diagram:

Electrical diagram 24VDC

Notes for the diagram:

Durability of the device depends on applied load.

For resistive load (light bulbs, etc.) and 4A

current consumption of each individual electrical

device, the durability exceeds 70.000 switches of

each individual electrical device.

Module Inclusion (Adding to Z-Wave

network)

 Connect module to power supply (with

temperature sensor connected - if

purchased),

 bring module within maximum 1 meter (3

feet) of the main controller,

 enable add/remove mode on main controller,

 auto-inclusion (30 minutes after connected

to power supply) or

 press service button for more than 2 S

second or

 press push button three times within 3s I1

(3 times change switch state within 3

seconds)

Module Exclusion/Reset (Removing

from Z-Wave network)

 Connect module to power supply

 bring module within maximum 1 meter (3

feet) of the main controller,

 enable add/remove mode on main controller,

 press service button for more than 6 S

second or

 press push button ﬁve times within 3s (5 I1

times change switch state within 3 seconds)

in the ﬁrst 60 seconds after the module is

connected to the power supply.

By this function all parameters of the module are

set to default values and own ID is deleted.

If service button S is pressed more than 2 and

less than 6second module is excluded, but

conﬁguration parameters are not set to default

values

Association

Association enables Flush 2 relays module to

transfer commands inside Z-Wave network

directly (without main controller) to other Z-Wave

modules.

Associated Groups:

Group 1: basic on/oﬀ (triggered at change of the

output Q1 state and reﬂecting its state) up to 16

nodes.

Group 2: basic on/oﬀ (triggered at change of the

output Q2 state and reﬂecting its state) up to 16

nodes.

Group 3: default reporting group (reserved for the

main controller).

Conﬁguration parameters

Parameter no. Input 1 switch type 1 –

Available conﬁguration parameters (data type is

1 Byte DEC):

 default value 1

 mono-stable switch type (push button) 0

 -stable switch type 1 bi

Parameter no. 2 Input 2 switch type –

Available conﬁguration parameters (data type is

1 Byte DEC):

 default value 1

 mono-stable switch type (push button) 0

 -stable switch type 1 bi

Parameter no. 10 - Activate / deactivate

functions ALL ON/ALL OFF

Available conﬁguration parameters (data type is

1 Byte DEC):

 default value 255

 255 - ALL ON active, ALL OFF active.

 - ALL ON is not active ALL OFF is not 0

active

 - ALL ON is not active ALL OFF active 1

 - ALL ON active ALL OFF is not active 2

On/Oﬀ module responds to commands ALL ON /

ALL OFF that may be sent by the main controller

or by other controller belonging to the system.

Parameter no. 11 - Automatic turning Oﬀ relay

Q1 after set time

Available conﬁguration parameters (data type is

2 Byte DEC):

 Default value 0

 - Auto OFF disabled 0

 1- 65535 = 10mseconds 655,35 seconds–.

Auto OFF enabled, with deﬁne time, step is

10mseconds.

Parameter no. 12 - Automatic turning Oﬀ relay

Q2 after set time

Available conﬁguration parameters (data type is

2 Byte DEC):

 Default value 0

 - Auto OFF disabled 0

 1- 65535 = 10mseconds 655,35 seconds. –

Auto OFF enabled, with deﬁne time, step is

10mseconds.

Parameter no. 30 - Saving the state of the

relays Q1 and Q2 after a power failure

Available conﬁguration parameters (data type is

1 Byte DEC):

 default value 0

 Flush 2 relays module saves its state 0 –

before power failure (it returns to the last

position saved before a power failure)

 - Flush 2 relays module does not save the 1

state after a er failure, it returns to "oﬀ" pow

position.

Parameter no. 40 Power reporting in Watts –

on power change for Q1

Set value means percentage, set value from 0 –

+VDC

-VDC

Output for electrical device no. 1

Output for electrical device no. 2

Input for switch to control electrical

device no.2

Input for switch to control electrical

device no.1

Terminal for digital temperature sensor

(only for Flush 2 relays module

compatible digital temperature sensor,

which must be ordered separately).

Neutral lead

Live lead

Output for electrical device no. 1

Output for electrical device no. 2

Input for switch to control electrical

device no.2

Input for switch to control electrical

device no.1

Terminal for digital temperature sensor

(only for Flush 2 relays module

compatible digital temperature sensor,

which must be ordered separately).

Service button (used to

add or remove module

from the Z-Wave

network).

Produkt Specifikationer

Mærke:	Qubino
Kategori:	Ikke kategoriseret
Model:	ZMNHBA2 power relay

Har du brug for hjælp?

Hvis du har brug for hjælp til Qubino ZMNHBA2 power relay stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Qubino Manualer

Qubino Flush RGBW Dimmer Manual

1 September 2024

Qubino ZMNHBA2 power relay Manual

27 August 2024

Qubino ZMNHSD1 Manual

27 August 2024

Qubino Flush 1 Relay Manual

27 August 2024

Qubino ZMNHAA2 Manual

27 August 2024

Qubino Flush 2 Relays Manual

27 August 2024

Qubino Flush 1D Relay Manual

27 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Siemens WQ32G28IL Manual

6 December 2025

MDT BE-TA550606.02 Manual

6 December 2025

Opticis USC-CC32 Manual

6 December 2025

Audio-Technica AT33xMONO Manual

6 December 2025

Bosch SPI4EMS24E Manual

6 December 2025

Fostex P1000K Manual

6 December 2025

Advantech UTC-124I1 Manual

6 December 2025

Anton/Bauer Titon Micro Kit Manual

6 December 2025

Philips Zoom! DayWhite DIS130 Manual

6 December 2025

Opticis USB-FC30AA Manual

6 December 2025