QuickCool QC-PC-C01C Manual

QuickCool Ikke kategoriseret QC-PC-C01C

Læs gratis den danske manual til QuickCool QC-PC-C01C (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om QuickCool QC-PC-C01C, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
Quick-Ohm Küpper & Co. GmbH
Components – Heat-Management - Ceramics
www.quick-ohm.com vXIII/07/nk
- 1 -
TEC - Controller QC-PC-C01C
Manual
Temperaturecontroller for Cooling
Technial Data:
Dimensions: 65mm x 50mm x 20mm
Temperature range: -20°C…+50°C
Input voltage: 10V…24V
Max. output voltage: equal to input voltage
Max. output current: 10A
1. Basic information QC-PC-C01C
The QC-PC-C01C was designed as controller for cooling to adjust a TEC (Thermoelectric coller)
at a certain temperature. The controller is operated by low DC voltage and should not be exposed
to main voltage. To set up the controller electrical wiring is required, which request some basic
knowledge of electrical circuits. All wiring must be done without connection to the power supply.
Be aware that same components can be damaged or destroyed be incorrect use. Despite of low
voltage, high currents can occur and serious warming and the danger of fire can appear by using
wrong lead wires. Please read this instruction carefully and consult an electrician by any question.
If you remark any warming during operation, the controller must be switched off immediately.
Scope of delivery:
1 TEC - Controller QC-PC-C01C
1 Temperaturesensor NTC 10K ( =3977K) Ω β
1 Potentiometer 10K Ω
1 Manual
Quick-Ohm Küpper & Co. GmbH
Components – Heat-Management - Ceramics
www.quick-ohm.com vXIII/07/nk
- 2 -
2. Operating principle:
A TEC is able to transfer thermal power from one side of the module to the other by consuming
electrical power. The temperature drops on one side of the element, because of heat consumption
while it rises on the other side. For using this heatpump effect in a technical application, a setup
similar to figure 1 is to be built up.
This is the basic setup for any TEC-Application. The area to be temperature controlled must be
equipped with a temperature sensor. On the opposite side, the removed heat must be dissipated to
the ambient. The size of the heatsink and the quality of the thermal contact to the TEC has the
biggest influence on the performance of the whole system. The gap between the TEC and the
mounted parts (hot/cold side) must be as small as possible and only a very little amount auf
thermal conductive should be used to avoid air inclusions in the contact areas. For further
information such as mechanical loads for a durable setup visit our website www.quick-ohm.com.
Heatsink/ hot
side
Thermal
conductive
(Paste, Foil,
etc.)
TEC
(printing on
upper side)
Temp. controlled
area/ cold side
figure 1:
Temperatur
e
sensor

Produkt Specifikationer

Mærke: QuickCool
Kategori: Ikke kategoriseret
Model: QC-PC-C01C

Har du brug for hjælp?

Hvis du har brug for hjælp til QuickCool QC-PC-C01C stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret QuickCool Manualer

QuickCool

QuickCool QC-PC-C01C Manual

31 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Synology

Synology CMA-01 Manual

1 August 2025
Synology

Synology RKS-02 Manual

1 August 2025
Navman

Navman MiVue 765 SAFETY Manual

1 August 2025
Navman

Navman MY75T Manual

1 August 2025
Exquisit

Exquisit AIRFRY 3010 Manual

1 August 2025
Navman

Navman MiVue 155 SAFETY Manual

1 August 2025
Navman

Navman MiVue 698 Manual

1 August 2025
Newland

Newland FM550 Manual

1 August 2025
Tripp Lite

Tripp Lite SRIN4181810 Manual

1 August 2025
Navman

Navman MyTruck III Manual

1 August 2025