Radson Turbo Manual

Radson Termostat Turbo

Læs gratis den danske manual til Radson Turbo (6 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 55 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 28 anmeldelser. Har du et spørgsmål om Radson Turbo, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

STARTING THE DEVICE:

Press the button 5 on the side of the Turbo to turn the

device on (Turbo + towel dryer).

• Indicators 2 and 3: Steady green - Turbo + Towel dryer

turned on

• Filter indicator 1: Off

• Indicator 3: Steady red - towel dryer running

BLOWER 2 OPERATING LIGHT:

• Off: Power Off

• Steady green: Power On

• Blinking red: Operating

TURBO 1000 WATT

The Turbo is designed to quickly raise the temperature in your bathroom.

• Install the timer in the same room as the towel dryer. The

timer must be installed about 1.5 metres above the ﬂoor,

on an inside wall, away from splashing water, direct

sunlight and direct source of direct thermal disturbance.

Note: To ensure proper infrared transmission:

- Do not obstruct transmitter and receiver cells

(bath towels in front of the cell).

- Avoid using electronic ballast lighting in the same room.

• Set the dial for the desired time and press the “OK / Boost”

button to start the blower.

NOTE: Forced operation of the device can be interrupted at

any time by pressing the “OK / Boost” button again. When

restarting the blower in this case, the remaining Boost time

will be the setting shown on the dial.

Infrared receiver on Turbo

1. Filter cleaning indicator

2. Blower operation indicator

3. Towel dryer operation indicator

4. Infrared receiver cell

5. Start/towel dry button

SPECIFIC CASES

Overheating

If towels or any other obstructions block the Turbo outlet

excessively, causing overheating, the device will shut down

(indicators 2 and 3 blinking red / green). The Turbo operation

will restart once the temperature cools, for the remaining

preset length of time.

Thermal safety:

If the Turbo resistor overheats a manually reset thermal

safety device mechanically stops blower operation.

Indicator light status:

• Filter indicator 1: Blinking red and

• Blower indicator 2: Steady green

Important: A dirty ﬁlter can cause overheating. Clean it if

necessary. Press button 5 “start/stop” for 5 seconds to stop

this alarm.

Note: Please clean the ﬁlter each time the Clean Filter alarm

is triggered (“see Cleaning the Filter”).

Caution: if the cause of overheating has not been identiﬁed

the alarm will be triggered again. In this case, please contact

the installer since this may cause the Turbo to deteriorate

over time.

The infrared timer trans-

mitter lets you send a start

command to the Turbo for

a variable period of 0 to 2

hours.

TIMER ON HOT WATER VERSION DEVICES

21 43 5

Replacing timer batteries

Batteries must be replaced when the Turbo does not respond to commands sent

by the timer (low or discharged batteries). Replace the batteries with 2 new LR3

alkaline batteries.

FILTER CLEANING

The Turbo is equipped with a dust ﬁlter which will stop the Turbo when it is satu-

rated (see «Thermal safety»).

Filter indicator 1 lights steady red after 200 hours of use. In this case the blower will

stop working and the ﬁlter must be cleaned. Blower indicator 2 will remain steady

green regardless of the commands from the timer or infrared transmitter.

Important: Power to the device must remain on for the ﬁlter cleaning alarm to be

turned off. (pictogram Nº5):

3 - Clean the ﬁlter using a vacuum or by

rinsing under water.

4 – Reposition the ﬁlter in the same way

as shown in Figure 2, by sliding to the

left or right.

5 – Press the Start / Stop button for 3

seconds. This will turn off the alarm.

The ﬁlter alarm will be triggered again

after 200 hours of use.

These pictograms show the procedure for cleaning the ﬁlter on the Turbo ﬁlter itself.

1 - Filter cleaning alarm:

FILTER indicator steady red.

2 - Remove the ﬁlter by sliding to the

left or right of the appliance.

TURBO 1000 WATT

Produkt Specifikationer

Mærke:	Radson
Kategori:	Termostat
Model:	Turbo

Har du brug for hjælp?

Hvis du har brug for hjælp til Radson Turbo stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Termostat Radson Manualer

Radson 51042 - Digital thermostat RF Thermostaat Manual

1 September 2024

Radson Turbo Manual

23 August 2024

Radson Infrared clock ET Manual

23 August 2024

Radson 51043 - WIRELESS RF MAIN ZONE Manual

21 August 2024

Radson TempCo Comfort 24V - 51021 Manual

19 August 2024

Radson 51035 - H-C module 24V Manual

18 August 2024

Radson 51055 - SLAVE RF Manual

18 August 2024

Radson Touch E3 Manual

28 Juli 2024

Radson 51023 - MAIN ZONE PROGRAMMER THERMOSTAT Thermostaat Manual

23 Juli 2024

Radson Tempco digital W Manual

19 Juli 2024

Termostat Manualer

Nyeste Termostat Manualer

Honeywell CT30A1005 Manual

14 August 2025

Honeywell RTH6450D Manual

14 August 2025

Honeywell CT62B1015/U Manual

14 August 2025

Renkforce MH-810HN Manual

14 August 2025

Honeywell RTH2310B1002/A Manual

13 August 2025

Honeywell CT53K1006/E Manual

13 August 2025

Honeywell CT87N1001/E1 Manual

13 August 2025

Honeywell RTH6580WF1001/U Manual

13 August 2025

Fantini Cosmi C900R Manual

13 August 2025

GE RAK190V Manual

12 August 2025