Radson Infrared clock ET Manual

Radson Termostat Infrared clock ET

Læs gratis den danske manual til Radson Infrared clock ET (18 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om Radson Infrared clock ET, eller vil du spørge andre brugere om produktet?

Side 1/18
1
Infrared Thermostat Transmitter with Digital Display - Instructions PPLIMP10314/Bd of 03/03/2011
Infrared receiver
A
B
C
A. Towel radiator pilot light
B. Towel radiator on/standby
button
C. Infrared receiver
D. Filter cleaning light
E. Turbo pilot light
F. Towel dryer pilot light
G. Infrared receiver
H. Towel radiator on/standby
button
I. Infrared transmitter
Installation and Use
Infrared clock thermostat with or without Turbo
1. Operating mode
2. Transmission indicator
3. Keypad lock activated
4. Exemption programme
5. Heating indicator
6. Day-time programme in Auto mode
7. Current time, programme no. or
parameter name
8. Current day
9. Boost activated
10. Low battery indicator
11. if ON => room temperature displayed
12. Temperature setting or room temperature
Presentation
This infrared transmitter with programmable digital dis-
play is designed to bring you comfort and energy savings.
It allows you to operate your towel radiator by remote
control.
It allows you to regulate room temperature to a desired
temperature (temperature setting).
The Boost function allows you to rapidly increase the
temperature in your bathroom and/or dry your towels.
You can set the room temperature using the sensor on
the transmitter or receiver. By default, the temperature is
set using the sensor on the receiver.
Powering on the device
After connecting your device to the electrical installation:
Electric or combined towel radiator: Appuyez sur le
bouton on the receiver at the bottom of the device
to turn the towel radiator on. The «A» LED lights up.
Electric or combined towel radiator with Turbo
option:
Press the «H» button on the side of the Turbo to
turn the thermostat on. The «F» LED lights up.
Infrared clock thermostat
with or without Turbo
Infrared receiver for Turbo
D E F GH
ENG
2Infrared Thermostat Transmitter with Digital Display - Instructions PPLIMP10314/Bd of 03/03/2011
The IR receiver has a self regulating system that memoris-
es status (on/off) information and temperature settings.
If the transmitter is off, or if the batteries are dead:
with the ‘Sensor’=Ext setting, the last order received is
used for regulation, even when the transmitter is off or
if the batteries are dead.
with the ‘Sensor’=Int setting, the receiver will shut off
automatically after 30 minutes maximum.
IMPORTANT: if your receiver is off, your towel radiator
will not receive orders from the IR transmitter with dig-
ital display. Your installation could freeze because the
device is unable to regulate.
Installing the IR transmitter with
digital display
Install the IR transmitter with digital display in the
same room as the towel radiator. The transmitter
must be installed about 1.5 meters from the floor on
an interior wall, away from splashing water, direct
sunlight and any disturbance from direct heat such as
lamps, television sets, heating pipes, air flows, etc.
Note: To ensure perfect IR transmission:
do not allow objects to come between the transmit-
ters and receivers (such as bath towels and bath
sheets).
avoid using lamps with built-in electronic ballast in
the same room.
Assembly instructions
Remove the battery protection tabs:
Press the clip on the bottom of the transmitter and
pull the front panel to remove.
The first step consists of choosing the language with
t u, then press OK.
LANG : Choose the language (FrANçais/English)
Next, choose Turbo control, if any t u then press
OK:
TURBO: Is the device equipped with a Turbo? (yes/no)
The third step consists of setting the time
(while display is blinking).
Using the + and - keys: Set the hours
then press OK.
Next, using the + and - keys, set the minutes
then press OK.
Next, using the + and - keys, set the minutes
then press OK.
(1 = Monday, 2 = Tuesday, 3 etc.)
Next, using the + and - keys: set the day and month
then press OK.
Operating mode
«A»/»F» LED status
radiator paused
«A»/»F» LED status
radiator is heating
«Sensor = EXT» (*)
«A»/»F» LED status
radiator is heating
«Sensor = INT» (*)
Standby
(by pressing the B button on
the receiver)
Off - -
Standby
Solid green
- -
Comfort Solid green Solid red Flashing red
Reduced Solid green Solid red Flashing red
Frost protection Solid green Solid red Flashing red
Boost - Flashing red Flashing red
Sensor default or
measured T°C > 35°C Flashing green/red - -
Min 20cm
1.50M
(*) Sensor =EXT => control via the sensor on the receiver installed on the towel radiator
Probe=INT => control via the transmitter sensor


Produkt Specifikationer

Mærke: Radson
Kategori: Termostat
Model: Infrared clock ET

Har du brug for hjælp?

Hvis du har brug for hjælp til Radson Infrared clock ET stil et spørgsmål nedenfor, og andre brugere vil svare dig