Rane AD 22 Manual

Rane Ikke kategoriseret AD 22

Læs gratis den danske manual til Rane AD 22 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 32 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 16.5 anmeldelser. Har du et spørgsmål om Rane AD 22, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Manual-1

OPERATORS MANUAL AD 22

AUDIO DELAY

AD 22 CONNECTION

When connecting the AD 22 to other components in your

system for the first time, leave the power supply for last. This

gives you a chance to make mistakes and correct them before

any damage is done to your fragile speakers, headphones,

ears, or brains. The AD 22 passes audio while it is unpowered

by virtue of its fail safe bypass relays (when the AD 22

functions as a wire). Turn the system volume down before

plugging in the AD 22’s power.

INPUTS AND OUTPUTS

The AD 22’s Inputs are electronically balanced. The

screw terminals prefer #6 spade connectors. Stripped or

tinned wire makes an unreliable union. Connect AD 22 shield

wires to the signal ground terminal, the chassis ground screw

or neither. The AD 22’s Outputs are balanced line drivers.

REMOTE RECALL TERMINALS

Each channel of the AD 22 has two nonvolatile Memories,

“A” and “B”. Connecting a switch between the GND and

CH1 or CH2 terminals permits recalling the Memories

remotely. Only a change in the switch position is sensed—

when the switch closes, Memory B for the given Channel is

recalled. When the switch opens, Memory A is recalled.

Connecting the two Channel terminals (CH1 & CH2) together

on one side of the same switch, permits stereo recall of

Memories A and B.

QUICK START

Quickly look around to make sure no one catches you reading this. You’re aware this is the manual aren’t you? Wow!

Most people only get about this far in a manual, but there are a few important things you should know about the AD 22. So

please keep reading. These few points are summarized in this Cliff Note version of the manual.

ADJUSTING SENSITIVITY. First apply a signal with nominal input level and adjust the SENSITIVITY controls so

the red CLIP LEDs just light, then back off so the LEDs do not turn on, even with high signal peaks.

SETTING DELAY. Now that the input signal is calibrated, press the CHAN button until the CHAN LEDs indicate the

Channel you want to set. We cover the special case of adjusting both Channels simultaneously later (both CHAN LEDs on).

Adjust the up/down buttons until the LED display shows the desired Delay. To adjust the Delay of the other Channel press

the CHAN button until the other Channel’s LED is lit, and adjust the Delay as before.

STORING DELAY. Press the STORE button (the STORE LED stops flashing). This stores the current Delay values

into each Channel’s current Memory (A or B). The current Memory for each Channel is indicated by the MEMORY LED

lit when editing that Channel. Both Channel's current Delay values are stored with each press of the STORE button.

RECALLING DELAY. To recall a stored Memory, press RECALL. Each press of this button alternately recalls stored

Memories (A then B then A…) for the selected Channel only.

A quick way to recall Memories into both Channels simultaneously, is to store both Channel’s values into the same

Memory. With both Channels selected (both CHAN LEDs on), press RECALL to restore both Channel's Memories at the

same time.

SETTING TEMPERATURE. The AD 22 is factory set for 22°C/71.6°F. To change this, press and hold DISPLAY

MODE and press one of the up/down buttons. Use the 1ms/COARSE buttons for degrees Celsius or the 10µs/FINE buttons

for degrees Fahrenheit. The LED display shows the temperature setting. Further pressing of the up/down buttons adjusts the

temperature setting. This temperature is used, with constant 30% humidity, to calculate the speed of sound for converting

delay times into distance.

NEVER CONNECT ANYTHING EXCEPT AN APPROVED RANE POWER SUPPLY TO THE RED THING THAT

LOOKS LIKE A TELEPHONE JACK ON THE REAR OF THE UNIT. This is an AC input and requires special attention if

you do not have a power supply exactly like the one originally packed with your unit. See the full explanation of the power

supply requirements elsewhere in this manual.

Note: It is normal to hear harmless short bursts of stored data playback when recalling a memory. Also, powering up

the AD 22 without input signal eliminates chirping that may occur when scrolling delay values.

WEAR PARTS: This product contains no wear parts.

Produkt Specifikationer

Mærke:	Rane
Kategori:	Ikke kategoriseret
Model:	AD 22

Har du brug for hjælp?

Hvis du har brug for hjælp til Rane AD 22 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Rane Manualer

22 Juni 2025

22 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

20 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

DS18 VOC8PRO Manual

5 November 2025

Icron Rover 2850 Manual

5 November 2025

Amaran Peak Manual

5 November 2025

WesAudio Timbre Manual

5 November 2025

MuxLab 500800-TX Manual

5 November 2025

Tripp Lite PDUMH30HVATNET Manual

5 November 2025

NeXtime Plug Inn 2610 ZI Manual

5 November 2025

MSI MS-ND82 Manual

5 November 2025

Sonifex Redbox RB-MSP6 Manual

5 November 2025

NeXtime Plug Inn 2610 ZW Manual

5 November 2025