Rane AD 22B Manual

Rane Ikke kategoriseret AD 22B

Læs gratis den danske manual til Rane AD 22B (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 32 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 16.5 anmeldelser. Har du et spørgsmål om Rane AD 22B, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Manual-1

OPERATORS MANUAL AD 22B

AUDIO DELAY

QUICK START

Quickly look around to make sure no one catches you reading this. You’re aware this is the manual aren’t you? Wow!

Most people only get about this far in a manual, but there are a few important things you should know about the AD 22B.

So please keep reading. These few points are summarized in this Cliff Note version of the manual.

ADJUSTING SENSITIVITY. First apply a signal with nominal input level and adjust the SENSITIVITY controls so

the red CLIP LEDs just light, then back off so the LEDs do not turn on, even with high signal peaks.

SETTING DELAY. Now that the input signal is calibrated, press the CHAN button until the CHAN LEDs indicate the

Channel you want to set. We cover the special case of adjusting both Channels simultaneously later (both CHAN LEDs on).

Adjust the up/down buttons until the LED display shows the desired Delay. To adjust the Delay of the other Channel press

the CHAN button until the other Channel’s LED is lit, and adjust the Delay as before.

STORING DELAY. Press the STORE button (the STORE LED stops flashing). This stores the current Delay values

into each Channel’s current Memory (A or B). The current Memory for each Channel is indicated by the MEMORY LED

lit when editing that Channel. Both Channel's current Delay values are stored with each press of the STORE button.

RECALLING DELAY. To recall a stored Memory, press RECALL. Each press of this button alternately recalls stored

Memories (A then B then A…) for the selected Channel only.

A quick way to recall Memories into both Channels simultaneously, is to store both Channel’s values into the same

Memory. With both Channels selected (both CHAN LEDs on), press RECALL to restore both Channel’s Memories at the

same time.

SETTING TEMPERATURE. The AD 22B is factory set for 22°C/71.6°F. To change this, press and hold DISPLAY

MODE and press one of the up/down buttons. Use the 1ms/COARSE buttons for degrees Celsius or the 10µs/FINE buttons

for degrees Fahrenheit. The LED display shows the temperature setting. Further pressing of the up/down buttons adjusts the

temperature setting. This temperature is used, with constant 30% humidity, to calculate the speed of sound for converting

delay times into distance.

Never connect anything except an approved Rane power supply to the red thing that looks like supply to the red thing

that looks like a telephone jack on the rear of the unit. This is an AC input and requires special attention if you do not have

a power supply exactly like the one originally packed with your unit. See the full explanation of the power supply require-

ments elsewhere in this manual.

Note: It is normal to hear harmless short bursts of stored data playback when recalling a memory. Also, powering up

the AD 22B without input signal eliminates chirping that may occur when scrolling delay values.

AD 22B CONNECTION

When connecting the AD 22B to other components in

your system for the first time, leave the power supply for last.

This gives you a chance to make mistakes and correct them

before any damage is done to your fragile speakers, head-

phones, ears, or brains. The AD 22B passes audio while it is

unpowered by virtue of its fail safe bypass relays (when the

AD 22B functions as a wire). Turn the system volume down

before plugging in the AD 22B’s power.

INPUTS AND OUTPUTS

The AD 22B’s Inputs and Outputs are electronically

balanced, so use only balanced wiring. The AD 22B’s shields

(pin 1) connect to chassis ground. Pin 2 is “hot” per AES

standards.

REMOTE RECALL TERMINALS

Each channel of the AD 22B has two nonvolatile Memo-

ries, “A” and “B”. Connecting a switch between the GND and

CH1 or CH2 terminals permits recalling the Memories

remotely. Only a change in the switch position is sensed—

when the switch closes, Memory B for the given Channel is

recalled. When the switch opens, Memory A is recalled.

Connecting the two Channel terminals (CH1 & CH2) together

on one side of the same switch, permits stereo recall of

Memories A and B.

WEAR PARTS: This product contains no wear parts.

Produkt Specifikationer

Mærke:	Rane
Kategori:	Ikke kategoriseret
Model:	AD 22B

Har du brug for hjælp?

Hvis du har brug for hjælp til Rane AD 22B stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Rane Manualer

22 Juni 2025

22 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

20 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

PAG Mini link 6002 Manual

4 November 2025

Wamsler K128 Manual

4 November 2025

Sonifex Redbox RB-DSD8 Manual

4 November 2025

Zotac ZBOX MI561 nano Manual

4 November 2025

MuxLab 500800-RX Manual

4 November 2025

Hawke Laser/LED Foregrip Manual

4 November 2025

Wooden Camera 213900 Manual

4 November 2025

Chauvet Freedom Flex Stick Battery Manual

4 November 2025

DS18 VOC8LD-PK Manual

4 November 2025

Sony XDCAM PXW-Z90 Manual

4 November 2025