Rane ECM 64 Manual

Rane Ikke kategoriseret ECM 64

Læs gratis den danske manual til Rane ECM 64 (26 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 10 anmeldelser. Har du et spørgsmål om Rane ECM 64, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/26

Manual-1

OPERATORS MANUAL ECM 64

CONFERENCE SYSTEM

Quick Start

The ECM 64 is a very versatile product with many applications. This section will help you with basic setup, then use the

Contents below to find the detail you need for your specific application.

Although the ECM 64 or ECM 64AD are configured to operate ‘out of the box’, to get the best performance please

review this manual for proper configuration and alignment (see page Manual-12). The ECM 64AD includes both the DH 1

Digital Hybrid and the ECA 1 Echo Canceller. If you are using the ECM 64 without these options, hardware and software

references to them in this manual will not apply.

The ECM 64 is configured using RaneWare® software. To become familiar with the ECM 64 signal routing, you can

load and run RaneWare on a PC before connecting the ECM 64. In RaneWare, click on the Device button and select

Offline ECM 64. This creates a virtual product which is fully operational, even saving and recalling system files as if it

were a real unit. Press F1 at any time to get help, then get information about any feature by clicking on it. Here at Rane, we

spend a lot of time putting together very informative help files, so please use them — you'll help us feel appreciated!

Before connecting any cables to the ECM 64, unplug the RS 3 power supply and turn the amplifier(s) down or off until

all connections are complete. Connect balanced audio INPUTS and OUTPUTS to the handy Euroblock connectors.

Connect the RW 232 INPUT jack to a serial (COM) port on a PC-compatible computer using a standard 9-pin RS-232

cable (a short one is supplied with the unit, intended to connect between multiple RW 232 units in a rack). The cable or

adaptor must not be a null-modem type. If this unit is to be used by itself, set the RW 232 DEVICE ADDRESS switch to

‘1’ by setting all switches off (down), except switch one (labeled ‘1’ on the chassis, the right-most switch). If there is more

than one unit, refer to “Setting the Device Address” on page Manual-7 to set a unique number.

After all connections are made, connect the RS 3 remote power supply and line cord. CAUTION: don’t connect anything

but an approved Rane power supply. If the RS 3 and the ECM 64 are getting power, the yellow POWER indicator lights.

Start your computer running Windows®, and launch RaneWare. Select System Setup from the System menu. Be

sure to select the COM port which is physically connected to the ECM 64 and RS-232 under Connection, and click OK.

Now, choose Select from the Device menu. Click on Poll, and Devices Found displays the number of units. Click the

Stop button. Select the unit listed in the Device Selection window and click OK. If no unit was found, refer to the

“Troubleshooting” section on page Manual-13.

Several clues indicate communication between the computer and the ECM 64. The yellow COM (communications)

indicator should flash periodically. The Memory numbers (1-16) near the top of the RaneWare screen should be black

rather than gray.

Most echo problems are caused by improper microphone placement and gain. To achieve good acoustic echo canceller

performance, setup is critical. Follow the “Alignment Procedure” on page Manual-12.

Table of Contents

Hardware

ECM 64 – Front Panel Description ............... 2

ECM 64 – Rear Panel Description ................. 3

Typical ECM 64AD Installation ...................... 4

Site Survey ........................................................... 6

ECM Connection ................................................ 6

Memory Recall Port........................................... 7

Software Operation .............................................. 8

Overview ............................................................... 8

System Requirements ...................................... 8

Software Installation ........................................ 8

Device Selection ................................................ 9

Memory & Security ............................................ 9

Saving & Printing ............................................... 9

Inputs ................................................................... 10

Outputs ............................................................... 10

Acoustic Echo Canceller ................................ 10

Digital Hybrid .................................................... 11

Alignment Procedure ......................................... 12

Troubleshooting .................................................. 12

ECM 64 Options ................................................... 13

Advanced Application ........................................ 14

Device Control Language ................................. 16

RW 232 Communications Interface ............... 24

Example Packet Expansion Code .................. 25

Compliance Notices ........................................... 26

WEAR PARTS: This product contains no wear parts.

Manual-2

Front Panel Description

 INPUT SIG and OL level indicators: SIG lights when the Input signal (before trim) is above –25 dBu for Mics and –19

dBu for Line inputs. OL lights when the Input signal (before trim) is within 2 dB of clipping.

 OUTPUT SIG and OL level indicators: SIG lights when the Output signal is above -19 dBu. OL lights when the Output

signal is within 2 dB of clipping. Use the INPUT and OUTPUT level indicators to check correct signal flow.

 GAIN Switches: Selects Input Gain between 0 dB (line level), 34 dB (most mics), or 46 dB.

 OFF HOOK button: Toggles between Off Hook (conference mode) and On Hook. The front panel OH indicator lights

when the ECM 64 is in conference mode and the telephone line has been siezed. This button can be disabled using the FP

Lock in RaneWare.

 VOLUME UP & DOWN buttons: When UP is pressed Out 1’s level is increased. When DOWN is pressed, Out 1’s level is

decreased. These buttons can be disabled using the FP Lock in RaneWare.

 OH Indicator – Off Hook: When lit, the ECM 64 is in conference mode. The DH 1 must be installed to light this indicator.

 RNG Indicator - Ring: When lit, there is an incoming call.

 PRV Indicator - Privacy: When lit, the ECM 64 is in privacy mode and all Mic Inputs are muted.

 MUT Indicator - MUTE: When lit, all ECM 64 Outputs are muted.

 AA Indicator – Auto Answer: When lit, the ECM 64 has been placed in Auto Answer and will accept an incoming call

when the number of rings matches the set ring count.

 LEVEL meter: Selectively displays any one of the inputs or outputs by using RaneWare or the PORT STEP button (see ).

This display is also used for status display, PORT STEP meter selection and errors.

• During download programming, the -6 LED flashes by itself indicating program data is transferring.

• During RW 232 operation, if the -3 LED flashes by itself, an RW 232 receive parity error occurred.

• During download programming, if the 0 LED lights by itself, the download program checksum does not match. The ECM 64

will not accept the program.

• If the +6 LED lights by itself either the system not ready, an RW 232 overflow has occurred or a flash memory error has

occurred. To remedy, cycle the power off, then back on.

 PORT STEP button: Pressing this for 1 second causes the LEVEL meter to flash its currently monitored Input or Output. If

this button is pressed and held for 3 seconds, the monitored port can be changed by pressing the button in 1 second steps. The

LEVEL Meter LEDs will step Mic Mix (-18), Line In (-15), Aux In (-12), Hybrid In (-9), Out 1 (-6), Out 2 (-3), Out 3 (-0)

and Hybrid Out (6), then back to Mic Mix (-18).

 COM indicator: flashes randomly when receiving valid data from the control system or PC. If the DEVICE ADDRESS is set

to 0, this indicator flashes steadily at ½ second intervals.

 POWER indicator: Lights when the ECM 64 operating system is running.

 Security cover: Installs over the GAIN switches once they are set.

Produkt Specifikationer

Mærke:	Rane
Kategori:	Ikke kategoriseret
Model:	ECM 64

Har du brug for hjælp?

Hvis du har brug for hjælp til Rane ECM 64 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Rane Manualer

22 Juni 2025

22 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

20 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

BSS Audio FCS-926 Manual

14 September 2025

Brandson 303842 Manual

14 September 2025

AMX DGX-O-DXF-MMS Manual

14 September 2025

Brandson 304024 Manual

14 September 2025

JILONG JL097109NPF Manual

14 September 2025

Brandson 303403 Manual

14 September 2025

AMX DVX-2250HD Manual

14 September 2025

AMX Vision² Manual

14 September 2025

AMX NMX-ENC-1100 Manual

14 September 2025

AMX UPC20+ Manual

14 September 2025