Rane MLM 82a Manual

Rane Ikke kategoriseret MLM 82a

Læs gratis den danske manual til Rane MLM 82a (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 35 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 18 anmeldelser. Har du et spørgsmål om Rane MLM 82a, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Manual-1

MLM 82a

MIC/LINE MIXER

OPERATORS MANUAL

MLM 82a CONNECTION

When connecting the MLM 82a to other components in

your system for the first time, leave the power supply for last.

This gives you a chance to make mistakes and correct them

without damage to your fragile speakers, ears and nerves.

MIC/LINE INPUTS 1-4

The four XLR jacks provided on the MLM 82a are

balanced MIC/LINE inputs. They will also accept unbalanced

connectors. Use only shielded cable for inputs. For best noise

rejection use two-conductor-plus-shielded wire, even for

unbalanced operation. Connect the shield at both ends to help

insure proper grounding. See the Sound System Interconnec-

tion RaneNote included with this manual for all cable

adaptations. Rane follows the AES recommended practice of

pin 2 positive, pin 3 negative, and pin 1 to shield. Switch any

input connected to a microphone to the MIC position (out)

using the associated switches on the rear panel. When

connecting line level signals, switch the input to the LINE

position (in). A single phantom power switch is provided for

the four MIC inputs. If LINE is selected, Phantom Power is

disabled for that input.

QUICK START

This section is provided as a convenience for those in a rush. If you are experienced with this unit or other Rane

products, these few words will refresh your memory.

INPUTS 1 through 4 may be microphone or line level. The choice between the two is made by setting the LINE push

buttons on the REAR of the unit next to the MIC/LINE INPUT JACKS. Each microphone input may be assigned to A B,

or A+B outputs using the front panel ASSIGN switches.

INPUTS 5 through 8 are stereo line inputs which may be set to mono using the recessed MONO switches located on

the front panel.

Internal switches allow setting output signal levels for MIC or LINE. The factory default setting is LINE. If the MLM

82a is connected directly to a power amplifier, equalizer or recorder input, choose LINE level. If the MLM 82a is con-

nected to a microphone jack of an existing sound system, choose MIC level.

Once Inputs, Outputs, and power are properly connected, with the OUTPUT LEVELS counterclockwise (off), set the

Input LEVELS as high as possible without causing the SIG/OL indicators to blink red except during extreme signal peaks.

Now slowly raise the OUTPUT LEVELS as desired.

Never connect anything except an approved Rane power supply to the red thing that looks like a telephone jack on

the rear of the MLM 82a. This is an AC input and requires special attention if you do not have a power supply exactly like

the one that was originally packed with your unit. See the full explanation of the power supply requirements on page

Manual-3.

STEREO LINE INPUTS 5-8

The ¼" connectors are line-level balanced/unbalanced

Inputs. If the MLM 82a is to be used with unbalanced

sources, consult the Sound System Interconnection RaneNote

included with this manual for proper wiring. Stereo Inputs

use both A and B jacks at each INPUT. INPUTS 5 through 8

also serve as mono Inputs when the front panel MONO

switch is engaged.

OUTPUTS

The MLM 82a’s OUTPUTS are balanced. The same

wiring conventions as the XLR Inputs apply. The type of

device following the MLM 82a must be considered when

setting the internal Output Level switch. Choose between

LINE (0 dB) or MIC (-40 dB) output, the factory setting is

LINE. If the MLM 82a is connected directly to a power

amplifier input, choose LINE level. If the MLM 82a is

connected to a micro-

phone jack on an

existing sound system,

choose MIC level. For

unbalanced OUTPUT

connections do not tie

pin 3 (i.e. “–”) to

ground.

WEAR PARTS: This product contains no wear parts.

Produkt Specifikationer

Mærke:	Rane
Kategori:	Ikke kategoriseret
Model:	MLM 82a

Har du brug for hjælp?

Hvis du har brug for hjælp til Rane MLM 82a stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Rane Manualer

22 Juni 2025

22 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

20 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

PAG Mini link 6002 Manual

4 November 2025

Wamsler K128 Manual

4 November 2025

Sonifex Redbox RB-DSD8 Manual

4 November 2025

Zotac ZBOX MI561 nano Manual

4 November 2025

MuxLab 500800-RX Manual

4 November 2025

Hawke Laser/LED Foregrip Manual

4 November 2025

Wooden Camera 213900 Manual

4 November 2025

Chauvet Freedom Flex Stick Battery Manual

4 November 2025

DS18 VOC8LD-PK Manual

4 November 2025

Sony XDCAM PXW-Z90 Manual

4 November 2025