Rane RPM 26v Manual

Rane Ikke kategoriseret RPM 26v

Læs gratis den danske manual til Rane RPM 26v (24 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Rane RPM 26v, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/24

Manual-1

OPERATORS MANUAL RPM 26v

DSP MULTIPROCESSOR

Windows

is a registered trademark of Microsoft Corporation; RaneWare is a registered trademark of Rane Corporation.

SYSTEM REQUIREMENTS

RaneWare works under Microsoft Windows

, on a PC or

laptop with an unused serial port.

RW 232, RaneWare’s protocol, uses a DB-9 cable less

than 50 feet long, connecting from the serial port of a com-

puter to the RPM 26v communications Input port. No

interface boxes are required; just a cable and your computer.

RaneWare can be fully demonstrated and used without an

actual RPM 26v attached. Simply select the OFFLINE

RPM 26v or any other OFFLINE unit under Select in the

Device menu.

A RaneWare CD comes with each unit. Installation is

simple. The latest version is downloadable 24 hours a day

from Rane’s Internet site: http://www.rane.com.

QUICK START

If you don’t read all of this document, you risk setting up your system improperly. But at least read this section and the

Input Trim section on page Manual-13. Paying careful attention to your system’s gain structure and setting the RPM’s

Input Trim properly are essential in maximizing the noise performance of your entire system. (See the enclosed RaneNote

“Setting Sound System Level Controls”.) Once you’re done reading and memorizing the manual, please recycle the paper it

is printed on by reconing an old speaker. If RaneWare has not yet been installed on your computer, refer to STEP BY

STEP RANEWARE INSTALLATION on page Manual-2 first.

Leave the audio connections on the RPM 26v until last. Connect the RW 232 INPUT jack on the unit’s rear to a serial

(COM) port on a PC-compatible computer using a standard 9-pin RS-232 cable. A short one is supplied with the unit,

which is intended to connect between units in a rack. The cable and adapter must not be a null-modem type.

Locate the RW 232 DEVICE ADDRESS switch on the rear panel. If this unit is to be used by itself, set the switch to

‘1’ by setting all switches off (down), except switch one (labeled ‘1’ on the chassis, the right-most switch when viewed

from the rear). If there is more than one unit, refer to Device Address Calculator in the software’s Help system or run

the included Device Address Calculator software and set a unique address for each unit.

Apply power by connecting the RS 3 remote supply’s 5-pin DIN jack to the rear of the unit, then connect the IEC end

to a powered AC outlet. CAUTION: Do not connect anything but an approved Rane power supply to this jack. The unit

does ground the chassis through the power cord. If the RS 3 and the RPM 26v are getting power, the yellow front panel

POWER indicator will be on.

Start your computer, run Windows

, and launch RaneWare by double-clicking on the RaneWare™ umbrella icon.

(See the next page for software installation instructions.) The Help file’s Software License Agreement appears the first

time RaneWare is run — read it all and close it. Then the System Setup window may appear. If it doesn’t, select

System Setup from the System menu. Be careful to select the COM port which is physically connected to the RPM 26v.

Click OK. Now, the Device Selection window may appear. If it doesn’t, choose Select from the Device menu. Click on

Poll… and the Devices Found: displays the units found. Click the Stop button to stop Polling. Select the unit from the

Device Selection window and click OK. If no unit was found, please refer to the TROUBLESHOOTING section at the

end of this manual or in the software’s Help system.

Several clues indicate communication between the computer and the RPM 26v. The yellow COM (communications)

indicator on the front of the unit flashes or stays on. The Memory numbers (1-16) near the top of the computer screen will

be black rather than gray. The Active indicator at the bottom left of the computer screen will be green.

Important Note: The RPM 26v contains many insightful, preprogrammed DSP Programs. Each “fixed” DSP Program

can be thought of as a unique “system setup,” i.e., 2-way crossover system, 3-way system, 2 x 6 splitter, etc. Each of the 16

Memories can contain a different DSP Program. Before connecting the RPM 26v to the other audio components in your

system, it is wise to choose and store the appropriate DSP Program for your system in all 16 Memories. This avoids the

problem of accidentally recalling a Memory that restores an undesired DSP Program, such as the case where you recall

from a 3-way DSP Program to a splitter: this sends full-range audio to all Outputs!

Once the proper DSP Program is stored in the RPM’s Memories, audio connections can be made. Turn the amplifier(s)

off until all connections are complete. Connect balanced audio INPUTS and OUTPUTS to the Euroblocks on the rear.

Note: If you have previously

installed an older version of RaneWare

and you just received a new RPM 26v

unit, you must reinstall the new version

of RaneWare that was shipped with

your unit. Use of an old version will

not work.

WEAR PARTS: This product contains no wear parts.

Produkt Specifikationer

Mærke:	Rane
Kategori:	Ikke kategoriseret
Model:	RPM 26v

Har du brug for hjælp?

Hvis du har brug for hjælp til Rane RPM 26v stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Rane Manualer

22 Juni 2025

22 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

20 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

PAG Mini link 6002 Manual

4 November 2025

Wamsler K128 Manual

4 November 2025

Sonifex Redbox RB-DSD8 Manual

4 November 2025

Zotac ZBOX MI561 nano Manual

4 November 2025

MuxLab 500800-RX Manual

4 November 2025

Hawke Laser/LED Foregrip Manual

4 November 2025

Wooden Camera 213900 Manual

4 November 2025

Chauvet Freedom Flex Stick Battery Manual

4 November 2025

DS18 VOC8LD-PK Manual

4 November 2025

Sony XDCAM PXW-Z90 Manual

4 November 2025