Rane TTM 54 Manual

Rane Ikke kategoriseret TTM 54

Læs gratis den danske manual til Rane TTM 54 (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 5 anmeldelser. Har du et spørgsmål om Rane TTM 54, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

Manual-1

TTM 54

PERFORMANCE

MIXER

OPERATORS MANUAL

Quick Start

Congratulations! You are now the proud owner of the

best Performance Mixer available. For experienced

turntablists, ninety percent of the operation of the

TTM 54 Performance Mixer is obvious —

however, the TTM 54 also has many unique

features. These new features will be mas-

tered more quickly if you read the entire

manual. Right! We know some of you can’t

resist jumping right in, so please read at least

this portion of the manual. It will help you get

a good start.

• GAIN TRIM: These controls are intended to set

the signal level before the Crossfader. Always set the

GAIN TRIM controls to indicate an average signal level

of +4 on the meter with the Program Faders set to maximum.

Never use the GAIN TRIM controls to set the output level. Always

use the MASTER LEVEL control to set the output level. This is a very

simple thing, yet makes a huge difference in the performance of your mixer.

• EFFECTS: The assignable effects loop allows insertion of a stereo effects processor into:

• Pre-Program Fader PGM 1 ....... Engage PGM 1 EFFECTS only.

• Pre-Program Fader PGM 2 ....... Engage PGM 2 EFFECTS only.

• Post-Crossfader MASTER ....... Engage both PGM 1 and PGM 2 EFFECTS switches.

• Read sections 햵 and 헆 for more information.

• PHONES: The headphone output of the TTM 54 is a high power output stage (unlike most you have used before). There

are some notable differences…

• The headphone output of the TTM 54 delivers very high volume into your headphones.

• To avoid pain, never put headphones on your head and then plug them in.

• Always start with the PHONES LEVEL turned down and then turn it up to the desired level.

• Because of the high current and low output impedance, never short one side to ground or short left and right

together as is possible with mono cup headphones. Note: Low power headphone stages typically use large

resistors on their outputs, which allow shorting, but prevent high power. The TTM 54 gives you high power but

does not allow shorting.

• MIC LEVEL: For best performance, keep this control at 0 when not in use.

• For instructions on rotating Phono/Line switches to the desired location, see page Manual-6.

• Do not spray cleaner or lubricant into the front of the Program Faders or Crossfader. The fluid will just run out the

bottom of the unit. Never use unapproved cleaner or lubricants such as skateboard wheel lube, as corrosive damage may

result, voiding the warranty. See page Manual-6 for cleaning and replacement instructions and cleaner recommendations.

• Never connect anything except an RS 1 or other approved Rane AC power supply to the thing that looks like a telephone

jack on the rear. This is an 18 VAC center-tapped power unit. Consult the Rane factory for replacement or substitution.

• WEAR PARTS: This product contains the following wear parts subject to the ninety (90) day warranty period described on

page Service-1: FT 45 Active Crossfader & Channel Fader Assembly(3); ST 1 Phono/Line Switch Assembly (2).

Manual-2

햲 햹 PGM 1 and PGM 2 input GAIN TRIM controls are used to adjust input level. With the Program Faders (see ) at

maximum, set controls to give a peak reading of +4 on the meter. Set the Master Level to minimum while adjusting). It is

always best to run the input level at +4 to +7. Use the MASTER LEVEL (see 헃) control to adjust the volume at the

MASTER OUT (see 헅).

햳 BASS and and TREBLE controls provide deep cut, Accelerated Slope™ EQ for PGM 1 PGM 2. This unique EQ design

makes it possible to eliminate “high end” or “bass beat” without changing the sound of the vocals. The graph shown in

Figure 1 indicates the response of the filters.

햴 BALANCE controls are used for LEFT/RIGHT balance of PGM 1 and PGM 2 or for LEFT/RIGHT Pan effect. Push the

control to the left and sound moves to the left channel. Push the control to the right and sound moves to the right channel.

햵 EFFECTS engage switches are provided for PGM 1 and PGM 2. These two switches determine the location of a single,

assignable, stereo EFFECTS LOOP.

‘ With PGM 1 and PGM 2 EFFECTS switches both out, the EFFECTS LOOP is not engaged.

‘ Push PGM 1 EFFECTS switch only, and the EFFECTS LOOP is inserted pre-Program Fader PGM 1.

‘ Push PGM 2 EFFECTS switch only, and the EFFECTS LOOP is inserted pre-Program Fader PGM 2.

‘ Push both PGM 1 and PGM 2 EFFECTS switches, and the EFFECTS LOOP is inserted post-Crossfader Master.

Figure 1. Bass & Treble Controls

Front and Rear Panel Descriptions

Produkt Specifikationer

Mærke:	Rane
Kategori:	Ikke kategoriseret
Model:	TTM 54

Har du brug for hjælp?

Hvis du har brug for hjælp til Rane TTM 54 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Rane Manualer

22 Juni 2025

22 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

20 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

BSS Audio FCS-926 Manual

14 September 2025

Brandson 303842 Manual

14 September 2025

AMX DGX-O-DXF-MMS Manual

14 September 2025

Brandson 304024 Manual

14 September 2025

JILONG JL097109NPF Manual

14 September 2025

Brandson 303403 Manual

14 September 2025

AMX DVX-2250HD Manual

14 September 2025

AMX Vision² Manual

14 September 2025

AMX NMX-ENC-1100 Manual

14 September 2025

AMX UPC20+ Manual

14 September 2025