Raymarine Cam50 Manual

Raymarine Marine Cam50

Læs gratis den danske manual til Raymarine Cam50 (2 sider) i kategorien Marine. Denne vejledning er vurderet som hjælpsom af 42 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 21.5 anmeldelser. Har du et spørgsmål om Raymarine Cam50, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Installation

Introduction

Your Raymarine CAM

50 CCTV camera is a

good quality color

camera available in two

models:

•E03016 - NTSC

format.

•E03017 - PAL format.

It is waterproof to IP63 standard and suitable

for use in indoor locations such as the wheel

house, salon or engine room.

Safety notices

What’s in the box?

What tools are required?

What accessories are

available?

To enable you to complete the cabling to instal

your camera the following are available:

• E06017 - 5 m extension cable.

• E06018 - 15 m extension cable

The cables can be joined in any combination to

achieve the required cable length.

Cable runs

You need to consider the following points

before installing your camera cables:

• You need to connect the camera to a

display unit and power supply.

• All cables should be adequately clamped

and protected from physical damage and

exposure to heat - avoid running cables

through bilges or doorways, or close to

moving or hot objects.

• Acute bends must be avoided.

• Where a cable passes through an exposed

bulkhead or deckhead, a watertight gland

or swan neck tube should be used.

• CCTV camera cables cannot be cut and

rejoined.

Installation

Having selected a suitable installation site:

1.Remove the

camera dome by

gently turning it

counter- clockwise

to release the

bayonet fixing.

2.Remove the

camera cover by

gently pulling it

away from the

dome baseplate.

3.Hold the base-

plate in the

required position

and using a

pencil mark the

fixing holes.

4. Using a suitable

drill bit make pilot

holes for the fixing

screws.

5.Fix the camera

and baseplate into

position using the

two screws

provided.

6.Make sure that

the cable is

placed in the

cable slot of the camera baseplate to

ensure that it is not pinched when the

baseplate is secured in position.

With the camera installed you can now adjust

the field of vision .

You cabn adjust both the pan and the tilt of the

camera.

To adjust the pan of the camera:

1. Loosen screw A.

2. Gently turn the camera assembly until the

lens is pointing in the required direction.

3. Gently pinch screw A to secure the camera

in position.

To adjust the tilt of the camera:

1. Loosen screw B.

2. Holding the edges of the camera plate

gently tilt the camera up or down into the

required position.

3. Gently pinch screw B to secure the camera

in position.

You should now connect the camera to your

display and check that the required image is

being shown.

Either adjust the image by changing the pan

and tilt as detailed above, or, replace the

camera dome and cover to complete the

installation.

Cable connections

The extension cables from

the camera to the display

unit are joined using the

male/female twist

connectors.

The adapter cable should

be used to connect the display and the power

supply to the camera. The adapter cable

connections are shown below.

CAUTION: Power supply

The CAM 50 CCTV camera is suit-

able for use on a 12 V DC power

supply only.

CAUTION: Power supply

A 0.5 A quick-blow fuse should be

fitted to the positive (red) lead of the

camera.

CAUTION: Installation

This product IS NOT suitable for

installation underwater.

This product contains no user

serviceable parts.

12V DC

ONLY

Drill

Drill bit Phillips

screwdriver

Camera

Dome

Cover

Female

Male

81294_1.fm Page 1 Friday, September 15, 2006 9:29 AM

CAM 50

User Guide

Technical SupportTechnical SpecificationMaintenance

If you do not have a breaker in the power

circuit, an in-line 0.5 A quick blow fuse should

be fitted to the positive (red) lead of the cable.

Maintenance and

Troubleshooting

Your Raymarine CAM 100 does not contain

user-serviceable parts. They should be

serviced only by authorized Raymarine service

technicians at a Raymarine factory facility.

Routine Maintenance

Routine maintenance should be carried out on

a regular basis:

• Examine all cables for signs of damage

such as chafing, cuts or nicks.

• Check that all cables are securely

connected.

• Spray the camera and lens with fresh water

and wipe with a soft lint-free cloth to

remove debris or salt deposits.

Troubleshooting

Waste Electrical and Electronic

Equipment (WEEE) Directive

Raymarine fully complies with the

WEEE directive and as part of its envi-

ronmental policy asks you to be aware

of how you should dispose of this

product properly. The crossed out wheelie bin,

illustrated on the left, and found on our prod-

ucts signifies that this product should not be

disposed of in general waste or landfill. Please

contact your local dealer, national distributor or

Raymarine Technical Services for information

on product disposal.

Restriction of the use of certain

Hazardous Substances

This product uses components

that comply with the requirements

of the Restriction of the use of

certain Hazardous Substances

(RoHS) Directive 2002/95/EC.

Warranty

To register your new Raymarine product,

please take a few minutes to visit our website

www.raymarine.com. It is important that

you register to receive full warranty benefits.

Technical support

Complete product information and interactive

help is available at:

www.raymarine.com

Problem Solution

Camera does not

function

1. Make sure that the cable is

sound and that all connec-

tions are tight and free from

corrosion.

2. Check system fuses.

3. Check that the display is set up

correctly to receive the

images.

Refer to the relevant display

handbook for full details.

Red +12 V

Black - 0 V

Video connector

D8537_1

Format NTSC 512 x 492 pixels

PAL 500x 582 pixels

Imager 1/3 Sony DSP Color CCD

Horizontal resolution 380TVL

Scanning system NTSC 525 lines 2:1 interlaced

PAL 625 lines

Video output Composite 75 Ohms

Shutter speed NTSC 1/60 - 1/100.000sec

PAL - 1/50 - 1/100.000 sec

Minimum illumina-

tion

0.3 Lux at F2

Waterproof IP63

Power connection 12 V tinned leads

Video connections Female BNC

Operating tempera-

tures -10oC to +50o C (-14o F to 122o F)

Power consumption 80 mA with regulated power

input.

Lens 3.6 mm

Best focus - 1.5 m

Viewable distance - 3.5 m

Document No:81294_1 Date: December 2006

RoHS

COMPLIANT

81294_1.fm Page 2 Friday, September 15, 2006 9:29 AM

Produkt Specifikationer

Mærke:	Raymarine
Kategori:	Marine
Model:	Cam50

Har du brug for hjælp?

Hvis du har brug for hjælp til Raymarine Cam50 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Marine Raymarine Manualer

Raymarine ES75 Manual

24 August 2024

Raymarine LightHouse II - 16 Manual

24 August 2024

Raymarine A75 Manual

24 August 2024

Raymarine GS195 Manual

24 August 2024

Raymarine A50D Manual

24 August 2024

Raymarine Cam100 Manual

23 August 2024

Raymarine i50 Manual

23 August 2024

Raymarine ES78 Manual

23 August 2024

Raymarine E165 Manual

23 August 2024

Raymarine i70 Manual

23 August 2024

Marine Manualer

Nyeste Marine Manualer

President PM 2010 WP Manual

15 Januar 2025

Rockford Fosgate PMX-8BB Manual

5 Oktober 2024

Simrad NSS Chartplotter Manual

23 September 2024

Rockford Fosgate PMX-2 Manual

21 September 2024

Rockford Fosgate T500X1br Manual

20 September 2024

Simrad NSS Manual

18 September 2024

Plastimo Echofish 300 Manual

27 August 2024

Silva S15 Manual

27 August 2024

Silva S15-N Navtex Manual

27 August 2024

IVT 8A Solar Manual

26 August 2024