RC4WD VVV-S0009 Manual

RC4WD Radiostyret legetøj VVV-S0009

Læs gratis den danske manual til RC4WD VVV-S0009 (5 sider) i kategorien Radiostyret legetøj. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 13 anmeldelser. Har du et spørgsmål om RC4WD VVV-S0009, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

Speed Controller Programming Instructions

20A/30A/40A/45A/60A/70A/80A/100A/125A/200A

Phrases 1 Enter programming Mode

1. Connect your motor and receiver to the speed controller, but do not connect the

battery yet.

2. Turn on your transmitter and move the throttle stick to the full throttle position (full

up). Please Note: Most Futaba transmitters have the throttle channel reversed by

default.

3. Connect your battery and the controller will initialize with a musical tone.

Phrases 2 Programming

After 3 seconds, the controller will start beeping a sequence of tones – a musical tone

followed by one or more beeps. Each sequence represents a parameter that you can program

and is repeated 3 times. The parameters are:

— Tone + 1 Beep Cell Type and No. of Cells

— . — Tone + 2 Beeps Throttle Setting

— . — . — Tone + 3 Beeps Brake Setting /Throttle type (for Heli)

— — — — Tone + 4 Beeps Direction and Cutoff Type

— — — — — Tone + 5 Beeps Timing Mode

— — — — — — Tone + 6 Beeps Pulse Width Modulation (PWM)

Step 1. Starting. When you hear the sequence for the parameter you wish to program, move the

throttle stick to the .center position

The controller will then of short and long beeps start beeping a Morse code sequence

representing the possible options you may choose for the selected parameter. See table 2 for

a list of all programmable options. Each option sequence is repeated 3 times.

Step 2. Select and save move the throttle stick back to the full up , the select the option,

position., When you hear the sequence for the option you wish to select. The controller will

then save the selected option, and It then goes back sound a long beep as a confirmation.

to the beginning of the programming sequence (phrases 2 step 1).

Step 3. Complete programming and save options. Setup all the parameters you need to change.

When complete, move the throttle stick to the lowest (down) position. The controller will

save all options and re-initialize in normal running mode so you can start your motor.

The table below summarizes the various programming options for each parameter:

A- Aircraft

B- Helicopter

A: Options for Aircraft

1.1 For (2S-7S)-ESC--Cell Type and Number

of Cells

• — 1 Short + 1 Long NiMh/NiCD Auto Cell Count - 0.8V/Cell

Cutoff Voltage

• — — • 1 Short + 2 Long + 1 Short 7S Li-Po (25.9V) – 21V Cutoff Voltage

• — • — 1 Short + 1 Long + 1 Short + 1 Long 6S Li-Po (22.2V) –18V Cutoff Voltage

• — • • 1 Short + 1 Long + 2 Short 5S Li-Po (18.5V) – 15V Cutoff Voltage

• • — — 2 Short + 2 Long 4S Li-Po (14.8V) – 12V Cutoff Voltage

• • — • 2 Short + 1 Long + 1 Short 3S Li-Po (11.1V) – 9V Cutoff Voltage

2S Li-Po (7.4V) – 8V Cutoff Voltage

1.2 For (4S-8S) ESC--Cell Type and Number

of Cells

• — 1 Short + 1 Long NiMh/NiCD Auto Cell Count - 0.8V/Cell

Cutoff Voltage

• — — • 1 Short + 2 Long + 1 Short 8S Li-Po (29.6V) – 24V Cutoff Voltage

• — • — 1 Short + 1 Long + 1 Short + 1 Long 7S Li-Po (25.9V) – 21V Cutoff Voltage

• — • • 1 Short + 1 Long + 2 Short 6S Li-Po (22.2V) – 18V Cutoff Voltage

• • — — 2 Short + 2 Long 5S Li-Po (18.5V) – 15V Cutoff Voltage

• • — • 2 Short + 1 Long + 1 Short 4S Li-Po (14.8V) – 12V Cutoff Voltage

1.3 For (6S-10s) ESC --Cell Type and

Number of Cells

• — 1 Short + 1 Long NiMh/NiCD Auto Cell Count - 0.8V/Cell

Cutoff Voltage

• — — • 1 Short + 2 Long + 1 Short 10S Li-Po (37V) – 30V Cutoff Voltage

• — • — 1 Short + 1 Long + 1 Short + 1 Long 9S Li-Po (33.3V) – 27V Cutoff Voltage

• — • • 1 Short + 1 Long + 2 Short 8S Li-Po (29.6V) – 24V Cutoff Voltage

• • — — 2 Short + 2 Long 7S Li-Po (25.9V) – 21V Cutoff Voltage

• • — • 2 Short + 1 Long + 1 Short 6S Li-Po (22.2V) – 18V Cutoff Voltage

2. Throttle Setting

•• — 2 Short + 1 Long Auto Throttle Range *

•• — — 2 Short + 2 Long 1.1ms to 1.8ms

•• — — — 2 Short + 3 Long Hard start*

•• — — — — 2 Short + 4 Long Soft start

3. Brake Setting

••• — 3 Short + 1 Long No Brake

••• — — 3 Short + 2 Long Soft Brake*

••• — — — 3 Short + 3 Long Medium Brake

••• — — — — 3 Short + 4 Long Hard Brake

4. Direction and Cutoff Type

Produkt Specifikationer

Mærke:	RC4WD
Kategori:	Radiostyret legetøj
Model:	VVV-S0009

Har du brug for hjælp?

Hvis du har brug for hjælp til RC4WD VVV-S0009 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Radiostyret legetøj RC4WD Manualer

RC4WD Z-S1027 Manual

31 August 2024

RC4WD Z-R0006 Manual

31 August 2024

RC4WD Z-B0058 Manual

31 August 2024

RC4WD VVV-S0074 Manual

31 August 2024

RC4WD Dakar Rally Scale Manual

31 August 2024

RC4WD Z-E0098 Manual

31 August 2024

RC4WD Z-S1028 Manual

31 August 2024

RC4WD VV-JD00071 Manual

31 August 2024

RC4WD Z-X0041 Manual

31 August 2024

RC4WD Z-K0057 Manual

31 August 2024

Radiostyret legetøj Manualer

Nyeste Radiostyret legetøj Manualer

FMS 1500mm Cessna 182 Manual

12 August 2025

ARRMA Granite Grom Mega 380 Manual

3 August 2025

Carson Linde H 40 D Manual

3 August 2025

Spektrum NX20 Manual

1 August 2025

Spektrum Avian 2813-1750Kv Manual

1 August 2025

Spektrum S120 Manual

1 August 2025

Spektrum S6295 Manual

1 August 2025

Spektrum Avian 60 Manual

1 August 2025

Spektrum S1200 Manual

1 August 2025

Spektrum iX20SE Manual

1 August 2025