Ridgid LR-60B Manual

Ridgid Ikke kategoriseret LR-60B

Læs gratis den danske manual til Ridgid LR-60B (32 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 8 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 4.5 anmeldelser. Har du et spørgsmål om Ridgid LR-60B, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/32

Max. Cable Size 300 mm................... 2185 mm2

600 MCM 350 MCM

Go to RIDGID.com/CrimpDies for the RIDGID Crimp Die/Electrical

Connector Compatibility Charts.

Tool Input Force 60 kN (6-ton) (13,500 lbs.)...................

QCS Coupling Type 6T QCS and 60kN QCS.............

Interchangeable Head

Weight 3.4 lbs. (1.6 kg) 3.4 lbs. (1.6 kg)..................................

Do not use LR-60B/LS-60B Crimp Heads with RIDGID

RE 53 Electrical Crimp Tools. This may cause incomplete crimps.

Inspection/Maintenance

Inspect the Latching Crimp Head before each use for issues that could

affect safe use.

1. Remove battery from electrical tool.

2 . Clean any oil, grease or dirt from the tool and head, including han-

dles and controls. This aids inspection and helps prevent the ma-

chine from slipping from your grip.

3 . Inspect the head for:

• Proper assembly and completeness.

• Wear, corrosion or other damage. Make sure that the latch works

properly and securely closes.

• Presence and readability of head markings.

•See electrical tool manual for inspection and maintenance of the

QCS coupling

If any issues are found, do not use the tool until corrected.

4. Inspect the electrical tool and any other equipment being used as

directed in their instructions. Confirm that the crimp dies are a clean,

undamaged matched set.

5. Lubricate the head pivot points with a light weight general purpose

lubricating oil. Wipe off any excess oil.

Set Up/Operation

1. Prepare the connection to be crimped per the connector manufac-

turer’s instructions.

2. Choose the appropriate crimp dies and equipment for the applica-

tion per their specifications. Make sure all equipment is inspected

and set up per its instructions.

3. Remove battery from electrical tool. Open the Latching Crimp Head

by pressing the latch release. Insert matching dies into the head.

Dies should fit snugly and securely, and the crimping profiles should

align. Do not force dies into head. If there are any issues with die fit,

do not use the tool. Do not operate tool without dies installed.

Do not use with 12 ton or 130 kN dies. This could cause improper

crimp connections.

Figure 2 – Installing Dies in Crimp Head

4. Changing Heads with QCS Coupling – See electrical tool manual.

5. With dry hands install the tool battery.

6. If needed, open the head by pressing the latch release and close

the head around the connector to be crimped. Make sure that the

latch is fully closed – do not operate the tool with the latch open or

partially open.

7. Follow all compression connector manufacturers’ instructions for

crimp location. Some wire sizes may require more than one crimp

per connection.

Center the connector squarely against the crimp profile in the sta-

tionary die. Improper placement can make an incorrect crimp or

damage the equipment.

WARNING

Read and understand

these instructions, the

electrical tool instruc-

tions, the instructions

for the dies to be used,

the instructions for the

connector to be crimped and the warnings and instructions for all

equipment and material being used before operating this tool to

reduce the risk of serious personal injury.

SAVE THESE INSTRUCTIONS!

•Keep your fingers and hands away from the crimp head during

the crimping cycle. Your fingers or hands can be crushed, fractured

or amputated if they are caught between the dies or the components

and any other object.

•Do not use on energized electrical lines to reduce the risk of elec-

trical shock, severe injury and death. Tool is not insulated Use

appropriate work procedures and personal protective equipment when

working near energized electrical lines.

•Large forces are generated during product use that can break or

throw parts and cause injury. Stand clear during use and wear ap-

propriate protective equipment, including eye protection.

•Never repair a damaged head. A head that has been welded, ground,

drilled or modified in any manner can break during use. Never replace

individual components. Discard damaged heads to reduce the risk of

injury.

•Use proper tool, die, connector and cable combination. Improper

combinations can result in an incomplete or improper crimp which in-

creases the risk of fire, severe injury or death.

Selection of appropriate materials and joining methods is the

responsibility of the system designer and/or installer. Before any installa-

tion is attempted, careful evaluation of the specific re quire ments should be

completed. Consult connector manufacturer for selection information.

If you have any questions concerning this RIDGID®product:

• Contact your local RIDGID distributor.

• Visit RIDGID.com to find your local RIDGID contact point.

• Contact Ridge Tool Technical Service Department at rtctechservic -

es@emerson.com, or in the U.S. and Canada call (800) 519-3456.

Description

RIDGID®LR-60B/LS-60B Latching Crimp Head Tools are designed to

crimp electrical compression connectors to their respective wire when

used with appropriate dies.

The tool is available either as an interchangeable head (For RIDGID®

RE 6/RE 60 or Ilsco Electrical Tool) or as part of a dedicated tool (RIDGID ®

RE-600 series tools).

Figure 1 – Round Crimp Head Square Crimp Head

(Interchangeable versions)

Specification

LR-60B LS-60B

Dies Used Commercially Commercially............................

Available Round Available Square

60 kN & 6 Ton 60 kN

Conforming to DIN

48083 Type 6M

RIDGID Die Series RDD-60, RDK-60 SDD-60...............

LR-60B/LS-60 Latching Crimp Heads Instructions

NOTICE

Round

Dies Latch Square

Dies

QCS

Coupling

Latch

Release

WARNING

Printed 2/17

999-999-472.09

EC42593 REV. D

The Emerson logo and RIDGID logo are registered trademarks of Emerson Electric Co. or RIDGID, Inc. in the U.S. and other countries.

All other trademarks belong to their respective holders.

Produkt Specifikationer

Mærke:	Ridgid
Kategori:	Ikke kategoriseret
Model:	LR-60B

Har du brug for hjælp?

Hvis du har brug for hjælp til Ridgid LR-60B stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Ridgid Manualer

28 November 2025

28 November 2025

28 November 2025

27 November 2025

25 November 2025

25 November 2025

25 November 2025

Ridgid SeeSnake RM200A Manual

25 August 2025

Ridgid SeeSnake Compact C40 DSL Manual

21 August 2025

Ridgid RB-FXP Manual

19 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vevor FX-3.5-24-8 Manual

30 November 2025

Vevor CLDMFGMS01 Manual

30 November 2025

Vevor SS-door2-NA-6 Manual

30 November 2025

Vevor HNT-4in-10 Manual

30 November 2025

MDT BE-GT04W.01 Manual

30 November 2025

Blustream HDBaseT HEX11WPW-TX Manual

30 November 2025

MuxLab 500860 Manual

30 November 2025

Vevor TP2A Manual

30 November 2025

Philips BRR484 Manual

30 November 2025

Vevor CLDMFGBS02 Manual

30 November 2025