Rockford Fosgate Punch Marine PM1000X1BD Manual

Rockford Fosgate Modtager Punch Marine PM1000X1BD

Læs gratis den danske manual til Rockford Fosgate Punch Marine PM1000X1BD (1 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Rockford Fosgate Punch Marine PM1000X1BD, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

The remote can be mounted in a variety of ways. Use the following instructions to mount the remote that suits your application.

1. Find a location that gives easy access to the remote.

2. Route the cable for the remote and connect to the ampliﬁer, .ﬁgure 1

Outside Panel Install

3. Using the screws supplied, install the mounting clip.

NOTE: The housing can be installed with the mounting tab up or down. See step 1 in ,use a ﬁgure 2

small ﬂat-blade screwdriver in the slot at the top of the remote and pry the remote assembly from

the housing. Reinstall housing as desired.

4. Slip the remote onto the mounting clip until it snaps into place.

5. Connect the cable to the back of the remote.

Panel Install-With Front Housing

The maximum panel thickness is 1/8” (0.125” or 3.18mm) for this type of installation.

Disassemble the remote as shown in as follows;ﬁgure 2

Ensure there is enough room within the panel area for connection and placement.

1. Use a small ﬂat-blade screwdriver in the slot at the top of the remote and pry the remote assembly from the

housing.

2. Cut a hole into the panel using the Hole Cut Template at the bottom of the page.

3. Run the cable to the hole,connect to the remote assembly and snap into place.

Panel Install-Without Housing-Disassembly

NOTE: The maximum panel thickness is 3/16” (0.1875” or 4.75mm) for this type of installation.

Disassemble the remote as shown in as follows;ﬁgure 2

1. Use a small ﬂat-blade screwdriver in the slot at the top of the remote and pry the remote assembly from the

housing.

2. Pull the control knob straight off to remove.

3. Use a paper clip or the ﬂat side of a small drill bit from the back side through the hole to push the cover plate

off the housing cover.

NOTE: If the clear plastic LED extender is attached to the cover plate, remove it.

4. Remove the nut and washer and remove the remote assembly from the housing cover.

Panel Install-Standard

Ensure there is enough room within the panel area for connection and placement.

1. Use either plate with the LED hole as a template for hole positions.

2. Drill a 9/32” hole (0.281” or 7.14mm) for the knob shaft and a 3/32” hole (0.094” or 2.39mm) for the LED through hole.

3. Install the remote from the back side of the panel,aligning the knob shaft and LED with the drilled holes.

4. Install the cover plate washer and nut. Do not over-tighten the nut,just tighten until ﬁrm and secure.

5. Turn the knob shaft counter-clockwise to it’s lowest setting. Position and install the knob.

6. Connect the cable to the back of the remote.

Panel Install-Separated LED Placement

We suggest the following be done only by an experienced installer. Use of a grommet and/or double-sided

tape (both not included) may be needed for a proper ﬁt of the LED. Rockford Fosgate will in no way be held

responsible for damage incurred by improper or novice installation.

Ensure there is enough room within the panel area for connection and placement.

1. Remove the LED from the remote assembly by pulling straight up, .ﬁgure 3

2. Connect the cord with the LED attached into the 2-pin connector behind the knob shaft housing.

3. Drill a 9/32” hole (0.281” or 7.14mm) for the knob shaft.

4. Install the remote from the back side of the panel, aligning the knob shaft with the drilled hole.

5. Install the smaller cover plate, washer and nut. Do not over-tighten the nut, just tighten until ﬁrm and secure.

6. Turn the knob shaft counter-clockwise to it’s lowest setting. Position and install the knob.

7. Locate the position of the LED hole where the cord is not being over-extended.

8. Depending on the method of mounting,either a grommet and/or double-sided tape, drill the hole for a snug ﬁt. Install the LED.

9. Connect the cable to the back of the remote.

Operation

Over excursion and subsequent damage may occur at high levels of boost

Use the Installation and Operation manual that came with your ampliﬁer for proper operation of the remote.

Hole Cut

Template

1-5/16˝ 1/8˝

1˝

9/32˝

PUNCH Level Control Remote Mounting Install

Figure 1

Figure 2

Figure 3

Printed in China11/12 1230-58154-01

Produkt Specifikationer

Mærke:	Rockford Fosgate
Kategori:	Modtager
Model:	Punch Marine PM1000X1BD

Har du brug for hjælp?

Hvis du har brug for hjælp til Rockford Fosgate Punch Marine PM1000X1BD stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Modtager Rockford Fosgate Manualer

Rockford Fosgate P4004 Manual

27 August 2024

Rockford Fosgate Punch P300-2 Manual

27 August 2024

Rockford Fosgate Power T1000-1bdCP Manual

27 August 2024

Rockford Fosgate Marine M1200-1D Manual

27 August 2024

Rockford Fosgate Punch P500X1bd Manual

27 August 2024

Rockford Fosgate Punch P1000X1bd Manual

27 August 2024

Rockford Fosgate Punch P450.2 Manual

27 August 2024

Rockford Fosgate Punch PBR400X4D Manual

27 August 2024

Rockford Fosgate Power T1500-1bdCP Manual

27 August 2024

Rockford Fosgate Punch P325.1 Manual

27 August 2024

Modtager Manualer

Nyeste Modtager Manualer

Advance A10 APEX Manual

24 December 2025

Chord Ultima Integrated Manual

24 December 2025

Phoenix Gold ZXM400.4ISO Manual

23 December 2025

Rega Solis Manual

23 December 2025

Rega Mercury Manual

23 December 2025

Extron DTP3 R 201 D Manual

15 December 2025

Pure Acoustics Maestra AVD5023 Manual

11 December 2025

Atoll AM400 Evolution Manual

8 December 2025

Atoll MA100 Manual

8 December 2025

Fostex AP25 Manual

7 December 2025