Rockford Fosgate Punch PEQ Manual

Rockford Fosgate Fjernbetjening Punch PEQ

Læs gratis den danske manual til Rockford Fosgate Punch PEQ (1 sider) i kategorien Fjernbetjening. Denne vejledning er vurderet som hjælpsom af 31 personer og har en gennemsnitlig bedømmelse på 4.2 stjerner ud af 16 anmeldelser. Har du et spørgsmål om Rockford Fosgate Punch PEQ, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Punch EQ Remote Install

The remote can be mounted in a variety of ways. Use the following instructions to mount the remote that suits your application.

1. Find a location that gives easy access to the remote.

2. Route the cable for the remote and connect to the amplifier, figure 1.

Outside Panel Install

3. Using the screws supplied, install the mounting clip.

NOTE: The housing can be installed with the mounting tab up or down.

See step 1 in figure 2, use a small flat-blade screwdriver in the slot

at the top of the remote and pry the remote assembly from the

housing. Reinstall housing as desired.

4. Slip the remote onto the mounting clip until it snaps into place.

5. Connect the cable to the back of the remote.

Panel Install-Disassembly

NOTE: The maximum panel thickness is 3/16” (0.1875” or 4.75mm) for this type of installation.

Disassemble the remote as shown in figure 2 as follows;

1. Use a small flat-blade screwdriver in the slot at the top of the remote and pry the remote assembly

from the housing.

2. Pull the control knob straight off to remove.

3. Use a paper clip or the flat side of a small drill bit from the back side through the hole to push the

cover plate off the housing cover.

NOTE: If the clear plastic LED extender is attached to the cover plate, remove it.

4. Remove the nut and washer and remove the remote assembly from the housing cover.

Panel Install-Standard

Ensure there is enough room within the panel area for connection and placement.

1. Use the plate with the LED hole as a template for hole positions.

2. Drill a 9/32” hole (0.281” or 7.14mm) for the knob shaft and a 3/32” hole (0.094” or 2.39mm)

for the LED through hole.

3. Install the remote from the back side of the panel, aligning the knob shaft and LED with the

drilled holes.

4. Install the cover plate washer and nut. Do not over-tighten the nut, just tighten until firm and secure.

5. Turn the knob shaft counter-clockwise to it’s lowest setting. Position and install the knob.

6. Connect the cable to the back of the remote.

Panel Install-Separated LED Placement

CAUTION: We suggest the following be done only by an experienced installer. Use

of a grommet and/or double-sided tape (both not included) may be needed

for a proper fit of the LED. Rockford Fosgate will in no way be held

responsible for damage incurred by improper or novice installation.

Ensure there is enough room within the panel area for connection and placement.

1. Remove the LED from the remote assembly by pulling straight up, figure 3

2. Connect the supplied cord to the LED.

3. Connect the cord from the LED into the 2-pin connector behind the knob shaft housing.

4. Drill a 9/32” hole (0.281” or 7.14mm) for the knob shaft.

5. Install the remote from the back side of the panel, aligning the knob shaft with the drilled hole.

6. Install the cover plate without LED hole, washer and nut. Do not over-tighten the nut, just tighten

until firm and secure.

7. Turn the knob shaft counter-clockwise to it’s lowest setting. Position and install the knob.

8. Locate the position of the LED hole where the cord is not being over-extended.

9. Depending on the method of mounting, either a grommet and/or double-sided tape, drill the hole for

a snug fit. Install the LED.

10. Connect the cable to the back of the remote.

Operation

CAUTION:Overexcursion and subsequent damage may occur at high levels of boost

Use the Installation and Operation manual that came with your amplifier for proper operation of the remote.

+20

-2

-0

+10

+12

+14

+16

+18

20 20k50 100 200 500 1k 2k 5k 10k

Bass Treble

Figure 3

Figure 2

Figure 1

12/06 B.M. 1230-53761-01Printed in China

Produkt Specifikationer

Mærke:	Rockford Fosgate
Kategori:	Fjernbetjening
Model:	Punch PEQ

Har du brug for hjælp?

Hvis du har brug for hjælp til Rockford Fosgate Punch PEQ stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Fjernbetjening Rockford Fosgate Manualer

Rockford Fosgate Punch PEQ Manual

1 Juni 2025

Rockford Fosgate Punch PMX-BTUR Manual

27 August 2024

Rockford Fosgate Punch PLC2 Manual

27 August 2024

Rockford Fosgate Punch PMX-1R Manual

27 August 2024

Rockford Fosgate Punch PMX-0R Manual

27 August 2024

Rockford Fosgate Punch PLC-U Manual

27 August 2024

Fjernbetjening Manualer

Nyeste Fjernbetjening Manualer

KICKY RIDE KR-RS-FL8 Manual

3 December 2025

Vivanco UR 12 N Manual

14 November 2025

Danfoss MPCAN Manual

10 November 2025

Vivanco RC-21966 Manual

9 November 2025

SmallRig Wireless Remote Controller 3902 Manual

3 November 2025

Abus Comfion FUBE80000 Manual

31 Oktober 2025

Abus Smartvest Pro FUBE45010 Manual

30 Oktober 2025

Philips SRU3030/10 Manual

28 Oktober 2025

Rotel RKP-200 Manual

15 Oktober 2025

One For All URC 4916 Manual

8 Oktober 2025