Rockford Fosgate Punch PLC2 Manual

Rockford Fosgate Fjernbetjening Punch PLC2

Læs gratis den danske manual til Rockford Fosgate Punch PLC2 (1 sider) i kategorien Fjernbetjening. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Rockford Fosgate Punch PLC2, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/1
The remote can be mounted in a variety of ways. Use the following instructions to mount the remote that suits your application.
1. Find a location that gives easy access to the remote.
2. Route the cable for the remote and connect to the amplifier, .figure 1
Outside Panel Install
3. Using the screws supplied, install the mounting clip.
NOTE: The housing can be installed with the mounting tab up or down. See step 1 in ,use a figure 2
small flat-blade screwdriver in the slot at the top of the remote and pry the remote assembly from
the housing. Reinstall housing as desired.
4. Slip the remote onto the mounting clip until it snaps into place.
5. Connect the cable to the back of the remote.
The maximum panel thickness is 1/8” (0.125” or 3.18mm) for this type of installation.
Disassemble the remote as shown in as follows;figure 2
Ensure there is enough room within the panel area for connection and placement.
1. Use a small flat-blade screwdriver in the slot at the top of the remote and pry the remote assembly from the
housing.
2. Cut a hole into the panel using the Hole Cut Template at the bottom of the page.
3. Run the cable to the hole,connect to the remote assembly and snap into place.
Panel Install-Without Housing-Disassembly
NOTE: The maximum panel thickness is 3/16” (0.1875” or 4.75mm) for this type of installation.
Disassemble the remote as shown in as follows;figure 2
1. Use a small flat-blade screwdriver in the slot at the top of the remote and pry the remote assembly from the
housing.
2. Pull the control knob straight off to remove.
3. Use a paper clip or the flat side of a small drill bit from the back side through the hole to push the cover plate
off the housing cover.
NOTE: If the clear plastic LED extender is attached to the cover plate, remove it.
4. Remove the nut and washer and remove the remote assembly from the housing cover.
Panel Install-Standard
Ensure there is enough room within the panel area for connection and placement.
1. Use either plate with the LED hole as a template for hole positions.
2. Drill a 9/32” hole (0.281” or 7.14mm) for the knob shaft and a 3/32” hole (0.094” or 2.39mm) for the LED through hole.
3. Install the remote from the back side of the panel,aligning the knob shaft and LED with the drilled holes.
4. Install the cover plate washer and nut. Do not over-tighten the nut,just tighten until firm and secure.
5. Turn the knob shaft counter-clockwise to it’s lowest setting. Position and install the knob.
6. Connect the cable to the back of the remote.
Panel Install-Separated LED Placement
We suggest the following be done only by an experienced installer. Use of a grommet and/or double-sided
tape (both not included) may be needed for a proper fit of the LED. Rockford Fosgate will in no way be held
responsible for damage incurred by improper or novice installation.
Ensure there is enough room within the panel area for connection and placement.
1. Remove the LED from the remote assembly by pulling straight up, .figure 3
2. Connect the cord with the LED attached into the 2-pin connector behind the knob shaft housing.
3. Drill a 9/32” hole (0.281” or 7.14mm) for the knob shaft.
4. Install the remote from the back side of the panel, aligning the knob shaft with the drilled hole.
5. Install the smaller cover plate, washer and nut. Do not over-tighten the nut, just tighten until firm and secure.
6. Turn the knob shaft counter-clockwise to it’s lowest setting. Position and install the knob.
7. Locate the position of the LED hole where the cord is not being over-extended.
8. Depending on the method of mounting,either a grommet and/or double-sided tape, drill the hole for a snug fit. Install the LED.
9. Connect the cable to the back of the remote.
Operation
Over excursion and subsequent damage may occur at high levels of boost
Use the Installation and Operation manual that came with your amplifier for proper operation of the remote.
Hole Cut
Template
1
2
3
4
1-5/16˝
1/8˝
1˝
2
1
9/32˝
PUNCH Level Control Remote Mounting Install
Figure 1
Figure 2
Figure 3
Printed in China11/12 1230-58154-01

Produkt Specifikationer

Mærke: Rockford Fosgate
Kategori: Fjernbetjening
Model: Punch PLC2

Har du brug for hjælp?

Hvis du har brug for hjælp til Rockford Fosgate Punch PLC2 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Fjernbetjening Rockford Fosgate Manualer

Rockford Fosgate

Rockford Fosgate Punch PEQ Manual

1 Juni 2025
Rockford Fosgate

Rockford Fosgate Punch PMX-BTUR Manual

27 August 2024
Rockford Fosgate

Rockford Fosgate Punch PLC2 Manual

27 August 2024
Rockford Fosgate

Rockford Fosgate Punch PMX-1R Manual

27 August 2024
Rockford Fosgate

Rockford Fosgate Punch PMX-0R Manual

27 August 2024
Rockford Fosgate

Rockford Fosgate Punch PLC-U Manual

27 August 2024

Fjernbetjening Manualer

Nyeste Fjernbetjening Manualer

KICKY RIDE

KICKY RIDE KR-RS-FL8 Manual

3 December 2025
Vivanco

Vivanco UR 12 N Manual

14 November 2025
Danfoss

Danfoss MPCAN Manual

10 November 2025
Vivanco

Vivanco RC-21966 Manual

9 November 2025
SmallRig

SmallRig Wireless Remote Controller 3902 Manual

3 November 2025
Abus

Abus Comfion FUBE80000 Manual

31 Oktober 2025
Abus

Abus Smartvest Pro FUBE45010 Manual

30 Oktober 2025
Philips

Philips SRU3030/10 Manual

28 Oktober 2025
Rotel

Rotel RKP-200 Manual

15 Oktober 2025
One For All

One For All URC 4916 Manual

8 Oktober 2025