Roland Texart RT-640 Manual

Roland Printer Texart RT-640

Læs gratis den danske manual til Roland Texart RT-640 (42 sider) i kategorien Printer. Denne vejledning er vurderet som hjælpsom af 42 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 21.5 anmeldelser. Har du et spørgsmål om Roland Texart RT-640, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/42

www.tefbrandbeveiliging.nl Tel: 0180 - 554555

FIRE ALARM DETECTOR

TECHNICAL SPECIFICATIONS

INSTALLATION

INSTALLING THE BASE

To ensure proper fit of the detector head to the base, all wires should be properly dressed at installation by positioning all wires flat

against terminals and fastening the wires away from connector terminals. The detector base can be mounted directly onto most standard

electrical junction boxes.

INSTALLING THE HEAD

Align detector components using provided alignment marks on both the head and base. Align detector mark and short alignment mark on

base. Fit the detector head onto the base and twist clockwise to secure it. After all detectors are installed, apply power to the control unit .

Test the detectors as described below.

TESTING

All remote signalling systems, releasing devices and extinguishing systems should be disconnected during the test period and

reconnected at the conclusion of testing. After powering the detector, check to see the indicator LED flashing every 5 seconds. If the LED

fails to flash, it indicates the non-functioning of the detector or fault wiring. Re-check the wiring or replace the detector if necessary.

SMOKE: Allow smoke from a cotton wick or test smoke aerosol to enter the detector’s smoke chamber for at least 10 seconds. When

sufficient smoke has entered, the detector will signal an alarm. This will be indicated by the illumination of the 2 Red LEDs provided. Make

sure to clear smoke out of the chamber before resetting in order to keep the detector at its current sensitivity setting.

HEAT: The detector to be tested should be subject to a flow of warm air at a temperature of between 65°C and 80°C. This requirement can

be met by some domestic hair dryers. Switch on the warm airflow and check that the temperature is correct and stable. From a distance of

several cms, direct the airflow at the guard protecting the thermistor. The detector should alarm within 60 seconds. Upon alarm

immediately remove the heat source and check that the Red LEDs of the detector are illuminated. If a detector fails to activate within 60

seconds, confirm connections and programming. If necessary replace unit. Note: After testing, check that the system is returned to

normal operation. Notify the appropriate authorities that the testing procedure has been completed and the system is active again.

MAINTENANCE

The recommended minimum requirement for detector maintenance consists of annual cleaning of dust from the detector head using a

low power vacuum cleaner. >> DO NOT ATTEMPT TO DISASSEMBLE THE DETECTOR

Detector Head

Detector Base

Alignment Marks

ZEOS-C

ma_zeosc_01_010001_en_180716

MADE IN PORTUGAL - EU

10 V to 30 V DC

Heat: 7 uA / Smoke: 33 uA / Smoke & Heat: 35 uA

24 mA - Alarm LEDs

According to EN54-5 or/and EN54-7

0.5-2.5 mm²

20 seconds max.

White / ABS

95% RH Non-Condensing

0°C to 50°C / -10°C to 85°C

100 mm (D) x 50 mm (H) inc. base / 144 g inc. base

ORION, ORION MINI, ORION EX, ORION-PLUS, QUAD ZMU and ZMU

SUPPLY VOLTAGE

CURRENT - QUIESCENT

CURRENT - DEVICE IN ALARM

SENSITIVITY

CABLE SIZE

RESET/START-UP TIMES

COLOUR / CASE MATERIAL

MAX. HUMIDITY

NORMAL / TRANSIENT OPER. TEMPERATURE

DIMENSIONS / WEIGHT

COMPATIBILITY

ORDER CODE DESCRIPTION

ZEOS-C-S

ZEOS-C-H

ZEOS-C-SH

| CERTIFICATE |

PHOTOELECTRIC SMOKE DETECTOR

RATE OF RISE/FIXED TEMP HEAT DETECTOR

MULTISENSOR SMOKE & HEAT DETECTOR

1328-CPR-0705

1328-CPR-0706

1328-CPR-0704

MECHANICAL SPECIFICATION

Produkt Specifikationer

Mærke:	Roland
Kategori:	Printer
Model:	Texart RT-640

Har du brug for hjælp?

Hvis du har brug for hjælp til Roland Texart RT-640 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Printer Roland Manualer

Roland VP-300 Manual

26 August 2024

Roland GX-24 Manual

16 August 2024

Roland SP-540V Manual

4 August 2024

Roland VP-540 Manual

3 August 2024

Roland SC-545EX Manual

2 August 2024

27 Juli 2024

25 Juli 2024

18 Juli 2024

15 Februar 2023

Roland Texart XT-640 Manual

26 December 2022

Printer Manualer

Nyeste Printer Manualer

Canon imageRUNNER ADVANCE DX C5840i Manual

4 November 2025

Xiaomi Instant Photo Printer 1S Set Manual

2 November 2025

Canon imageCLASS LBP246dw II Manual

1 November 2025

Canon imageCLASS MF665Cdw Manual

1 November 2025

Canon imageCLASS LBP247dw II Manual

31 Oktober 2025

Canon imageCLASS MF751Cdw II Manual

31 Oktober 2025

Canon imageCLASS MF753Cdw II Manual

31 Oktober 2025

Canon imageFORCE 1440P Manual

30 Oktober 2025

Canon PIXMA TS4320 Manual

30 Oktober 2025

Canon imageCLASS MF663Cdw Manual

30 Oktober 2025