Sanus NFC18 Manual

Sanus højttalerstøtte NFC18

Læs gratis den danske manual til Sanus NFC18 (2 sider) i kategorien højttalerstøtte. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Sanus NFC18, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

1] Remove all parts from package. Damaged

or missing parts can be quickly obtained

by contacting Sanus Customer Service

at (800) 359-5520 or www.sanus.com.

2] Group the top plate and base with the pil-

lars. The speaker cable hole in the base

and the bolt mounting hole in the top plate

should be to the rear of the pillar.

3] Using the 2.25” base screws, align

countersunk holes in the base plate with

corresponding holes in either end of each

pillar. Tighten screws with a large tipped

Phillips screw driver. A little hand soap on

the threads may make the screws easier

to turn. Using the 1.25” top plate screws,

align countersunk holes in the top plate

with corresponding holes in each pillar

and tighten. Make sure that each screw

is following the pilot hole. To avoid strip-

ping the screw holes, donʼt use a power

screwdriver.

4] Two forms of speaker mounts are pro-

vided, adjustable speaker studs and

rubber pads. If you do not wish to angle

the speaker upwaerd, twist a rubber pad

into each corner of the top plate. To angle

the speaker use the adjustable speaker

studs in the front corners of the top plate

and rubber pads in the rear corners. When

the required angle is achieved, lock the

stud in place by threading a nut against

the bottom of the top plate. Place a cap

over each stud.

Page 2 Page 3 * PLEASE READ THE NOTE ON PAGE 4 OF THIS MANUAL!

Top Plate & Pillars

a] Adjustable Front

Studs

b] Lock Nuts

c] Top Plate

d] Rear Rubber Pads

e] Pillars

Front View NFC18c

a] Plastic Feet

b] Base

c] Pillar

d] Top Plate

Parts List

NFC18

Adjustable Speaker Stud Cap -a 2

5/8” Pan Head 1/4-20 Bolts -b 4

Lock Nuts -c 6

Adjustable Speaker Stud -d 2

1.25” Base Screws -e 4

2.25” Base Screws -f 4

Rubber Pads (wheel of 8) -g 2

Adjustable Spiked Feet -h 4

Plastic Isolation Feet (set of 4) -c 1

Steel Top Plate 1

Wood Base Plate 1

Pillars 2

13.5” Wire Cover 2

Produkt Specifikationer

Mærke:	Sanus
Kategori:	højttalerstøtte
Model:	NFC18

Har du brug for hjælp?

Hvis du har brug for hjælp til Sanus NFC18 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

højttalerstøtte Sanus Manualer

Sanus HTB3 Manual

28 December 2024

Sanus EF24 Manual

28 December 2024

Sanus BSWM3IWP Manual

6 September 2024

Sanus WSWM3IWP Manual

6 September 2024

1 September 2024

1 September 2024

1 September 2024

1 September 2024

1 September 2024

1 September 2024

højttalerstøtte Manualer

Nyeste højttalerstøtte Manualer

Sonorous SP 600 Manual

27 Februar 2025

Axis TC1601 Manual

20 Februar 2025

SoundTube SM1290 Manual

20 Februar 2025

Nubert BS-652 Manual

5 Februar 2025

NeoMounts NS-SHELF100 Manual

14 Januar 2025

Sonos Arc Ultra Wall Mount Manual

14 Januar 2025

Omnitronic STS-1 Manual

31 December 2025

Omnitronic EUMO-2 Manual

31 December 2025

Konig & Meyer 24496 Manual

30 December 2025

Bowers Wilkins FS-700 S3 Manual

30 December 2025