Sanwa MX-3 Manual

Sanwa Radio MX-3

Læs gratis den danske manual til Sanwa MX-3 (2 sider) i kategorien Radio. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Sanwa MX-3, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

MX-3

Get The Advantage

3 Channel Computer

Radio System

MODEL

BATT

REV

ARC

SUB-T

MODEL

EPAD/R

L R

DSC

Super Micro

3 CH. Receiver

92836 75 FM

Mhz

#1 #2 #3

Steering

Throttle

AUX

B/DSC

Switch

AA Dry Cell Battery Holder

Mechanical Speed Controller

DSC

Super Micro

3 CH. Receiver

92836 75 FM

Mhz

Electronic Speed Controller

ESC

TRANSMITTER BATTERY INSTALLATION

RECEIVER AND SERVO CONNECTIONS

Your MX-3 Computer R/C system receiver is NOT

equipped with BEC circuitry. DO NOT use more

than 6.0 volts to power the receiver. Anything higher

than 6.0 volts will burn-up or destroy your receiver.

Only use a 4.8~6.0 volt battery pack or a speed

controller that is designed to lower the voltage to

the receiver. The following diagram shows a typical

connection for the servos and receiver.

Note that the receiver antenna should be located at

least 2” (50mm) away from any servo leads and

switches. In electric cars, we recommend that it be

at least 4” (100mm) from the electric motor.

Extend the receiver antenna to the full length. Failure

to do so will cause loss of control. Do not cut or bend the

receiver antenna.

Insulate the connectors with tape or use tie wraps to

avoid contact with metal car chassis.

Please follow the model manufactures recommendations

for the correct installation of your radio system in your

car or boat.

Switch

To Battery

To Motor

CAUTION

When installing your MX-3 radio

system in your model, always

make sure to set your model on

a stand so the wheels are free

from any traction before turning

on your radio and or connecting

your motor for the first time.

TRIGGER POSITION ADJUSTMENT

Throttle Trigger Set

Screw

Throttle Trigger Position Gauge

Throttle Trigger Adjustment screw

NOTE:

Trigger Set Screw must be

loosened before adjusting

The Throttle Trigger can be adjusted to

give you a more natural feel of the throttle.

To Adjust:

1. Loosen the Throttle Trigger set screw

by turning counter clock-wise.

2. Turning the adjustment screw clock-wise

will move the trigger out or in the (A)

direction.

3. Turning the adjustment screw counter

clock-wise will move the trigger in or

towards the (B) direction.

4. After adjustment is made, re-tighten

the Trigger Set Screw.

5. Total adjustment for the trigger is 10mm.

Do Not over tighten adjustment screw,

it may damage the adjuster and or

the threads.

TROUBLESHOOTING GUIDE and WARNINGS

If your radio system does not operate properly, please

check the following items:

1. Make sure the batteries are properly installed and

fully charged. With alkaline batteries, make certain

the batteries are installed in the correct direction.

2. Check that both the transmitter and receiver power

switches are in the ON position.

3. Check the battery voltage by turning on the transmitter

and pushing both menu bottons at the same time

and releasing.

4. Make sure that the proper frequency crystals are

installed in both the transmitter and receiver.

5. Make sure all the receiver and servo connections

are tight.

WARNINGS:

DO NOT OPERATE YOUR SYSTEM IF SOMEONE

ELSE IS ON YOUR FREQUENCE AT THE SAME TIME.

YOUR MODEL CAN CAUSE SERIOUS DAMAGE OR

INJURY SO PLEASE USE CAUTION AND COURTESY

AT ALL TIMES.

DO NOT EXPOSE THE RADIO SYSTEM TO WATER

OR EXCESSIVE MOISTURE.

PLEASE WATER PROOF THE RECEIVER AND SERVOS

BY PLACING THEM IN A WATER TIGHT RADIO BOX

WHEN OPERATING R/C BOAT MODELS.

IF YOU HAVE LITTLE OR NO EXPERIENCE OPERATING

R/C MODELS, WE STRONGLY RECOMMEND YOU SEEK

THE ASSISTANCE OF EXPERIENCED MODELERS OR

YOUR LOCAL HOBBY SHOP FOR GUIDANCE.

To Open slide Cover Install Batteries To Close slide cover

Press down on the battery cover and slide

in the direction of the arrow to remove.

Install 8 pieces “AA” size alkaline batteries as

indicated on the battery tray. Make sure to match

the polarity (+ and -) as shown in the battery

compartment or the transmitter will not function.

Install the battery cover in place and slide to close.

WARNING: Improper installation of transmitter batteries

can cause serious damage to your system.

To Battery

To Motor

DIGITAL CONTROL SYSTEM

INC / DEC

ESC

REGISTRATION NUMBER

The abbreviation, IC, before the registration number signifies that registration was performed based on a

Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not

imply that Industry Canada approved the equipment.

Produkt Specifikationer

Mærke:	Sanwa
Kategori:	Radio
Model:	MX-3

Har du brug for hjælp?

Hvis du har brug for hjælp til Sanwa MX-3 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Radio Sanwa Manualer

7 December 2024

28 August 2024

28 August 2024

28 August 2024

Sanwa Blazer Sport Manual

28 August 2024

Sanwa MX3S Manual

23 August 2024

Radio Manualer

Nyeste Radio Manualer

Sencor SRD 7790B Manual

15 December 2025

Energy Sistem Home Speaker 7 Micro Manual

15 December 2025

Energy Sistem Fabric Box 3+ Manual

15 December 2025

Pinell Compact Manual

10 December 2025

Energy Sistem Urban 2 Manual

10 December 2025

TechniSat DigitRadio 425 Manual

9 December 2025

Sencor SRD 7760 Manual

8 December 2025

Sencor SRD 216 Manual

7 December 2025

Raddy RF320 Manual

5 December 2025

Ozito PDRS-018 Manual

4 December 2025