Satco S11969 Manual

Satco overvåge S11969

Læs gratis den danske manual til Satco S11969 (6 sider) i kategorien overvåge. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om Satco S11969, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

Satco Products, Inc.

CCT SELECTABLE LED

LINEAR T8 TYPE B LAMPS

Models: S11919, S11929, S11969

INSTALLATION AND SAFETY INSTRUCTIONS

IMPORTANT: Read before installing xture. Retain for future reference.

WARNING:

• DANGER: Risk of shock-disconnect power before

installation.

• WARNING: Risk of re or electric shock. LED

Retrot Kit installation requires knowledge of luminaire

electrical systems. If not qualied, do not attempt

installation. Contact a qualied electrician.

• WARNING: Product must be installed in accordance

with the national electrical code or your local electrical

code. If you are not familiar with these codes and

requirements, contact a qualied electrician.

• WARNING: Install this kit only in luminaries that have

the construction features and dimensions shown in the

photographs and/or drawing and where the input rating

of the retrot kit does not exceed the input rating of

the luminaire.

• WARNING: To prevent wiring damage or abrasion,

do not expose wiring to edges of sheet metal or other

sharp objects.

• WARNING: NOTE: Shunted lamp holders are found

only in uorescent luminaries with instant-start

ballasts. Instant-start ballasts can be identied by the

words “Instant Start” or “I.S.” marked on the ballast.

This designation may be in the form of a statement

pertaining to the ballast itself, or may be combined

with the marking for the lamps with which the ballast

is intended to be used, for example F40T 12/IS, for

more information contact the LED luminaire retrot kit

manufacturer.

Do not make or alter any open holes in an enclosure of

wiring or electrical components during kit installation.

Installers should not disconnect the existing wire from

lampholder terminals to make new connections at

lampholder terminals. Instead installers should cut

existing lampholder leads away from the lampholder

and make new electrical connections to lampholder

lead wires by employing applicable connectors.

• WARNING: Luminaire wiring and electrical parts

may be damages when installing retrot kit hardware.

Check for enclosed wiring and components.

• WARNING: Check the existing wiring for damage

before installing upgrade kit. Do not install if existing

wires are damaged.

This retrot kit is accepted as a component of a

luminaire where the suitability of the combination shall

be determined by authorities having jurisdiction.

THIS RETROFIT KIT INCLUDES, LED TUBE,

OPERATING INSTRUCTIONS, AND FIXTURE LABEL

FOR THE DOUBLE OR SINGLE ENDED APPLICATION.

• “This luminaire has been modied and can no longer

operate the originally intended lamp,” shall be marked

on the retrot luminaire where readily visible by the user

during normal maintenance including lamping.

• Do not use with dimmers.

• Suitable for damp locations.

• Suitable for use in enclosed luminaries, not vapor tight.

• Suitable for use with the following emergency

equipment; SATCO Products, Inc., model S8000,

S8002; 5Watt or 10 Watt Emergency LED Driver.

• This device complies with Part 15 of the FCC rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference,

and (2) This device must accept any interference

received, including interference that may cause

undesired operation.

Item

Number

Description

CCT Watts Hours Lumens

Minimum Lamp

Compartment Dimensions

(Length x Width x Height)

Lamp-to-Lamp

Spacing

S11919 12.5T8/LED/48/840-850-865/BP/2PK

40-50-65K

12.5W 50,000 1800

47 7/8 x 23 7/8 x 4 inches

(121.5 x 60.5 x 10 cm)

4 3/8 inches

(11cm)

S11929 12.5T8/LED/48/840-850-865/BP

S11969 12.5T8/LED/48/830-835-840/BP 30-35-40K

The units covered by this report were intended to retrot surface mount, Type IC or non-IC recessed mount Listed uorescent

luminaires that use maximum 4 tubular lamps, the minimum lamp compartment dimensions are tabulated below.

Satco Products, Inc.

FEATURES

• c-UL-us classied and recognized

• Full glass housing: No aging, yellowing, bending

APPLICATIONS

Widely used in residential buildings, ofces, shopping malls, supermarkets, hospitals, assembly lines, warehouses, etc.

for energy saving illumination.

Single Ended Double Ended

Typical Shunted LampholdersTypical Non-Shunted Lampholder

SINGLE-ENDED WIRING INSTALLATION

Removing Existing Fluorescent System

1. Disconnect power from xture.

2. Remove uorescent lamp(s).

3. Remove lens and wiring compartment, if applicable.

4. Cut all wires connected to the ballast as shown below and remove ballast.

5. Identify what type of lampholders are in xture. Single-Ended wiring installation of SATCO tubes requires

non-shunted G13 lampholders.

6. If applicable, replace lampholders with non-shunted lampholders.

CAUTION: Use only non-shunted lamp holders for Single-Ended wiring installations.

Do not perform Single-Ended wiring installation of product in a xture with shunted lampholders (found in all xtures using

instant start ballasts, Figure 2). If the existing lampholders are shunted, and Single-Ended wiring is desired, remove and

replace them with non-shunted lampholders (or remove the external shunt if applicable). make new connections directly to

lampholder terminals as shown in Figure 1 below.

Typical Ballast Congurations (NOTE: [

] Indicates where to cut existing wiring.)

A B C

Figure 1 Figure 2

Produkt Specifikationer

Mærke:	Satco
Kategori:	overvåge
Model:	S11969

Har du brug for hjælp?

Hvis du har brug for hjælp til Satco S11969 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

overvåge Satco Manualer

30 Marts 2025

30 Marts 2025

30 Marts 2025

30 Marts 2025

30 Marts 2025

30 Marts 2025

30 Marts 2025

30 Marts 2025

30 Marts 2025

30 Marts 2025

overvåge Manualer

Nyeste overvåge Manualer

BenQ DesignVue PD2730S Manual

8 April 2025

Asus VA279QGS Manual

8 April 2025

Acer EV227Q Manual

8 April 2025

BenQ PD3226G Manual

7 April 2025

Philips 221V8LB Manual

4 April 2025

PureTools PT-SCREEN-100 Manual

1 April 2025

Cooler Master GM27QPA Manual

28 Marts 2025

Philips 230V8 Manual

5 Marts 2025

ProDVX UW-24 Manual

5 Marts 2025

Asus ZenScreen MB166CR Manual

27 Februar 2025