Schlage WCW100 Manual

Schlage Overvågningskamera WCW100

Læs gratis den danske manual til Schlage WCW100 (5 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 11 anmeldelser. Har du et spørgsmål om Schlage WCW100, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/5
Camera User Guide
There are two cameras available for use with the Schlage
LiNK system.
WCW100
The WCW100 is a wireless camera that communicates
with the Schlage LiNK system through your existing
wireless router.
WCE100
The WCE100 is a wired camera that communicates with
the Schlage LiNK system through your existing router.
POWER
NETWORK
WCW100 Wireless Camera
POWER
NETWORK
WCE100 Wired Camera
DO NOT connect Ethernet or power before
enrolling the camera.
For indoor use ONLY!
!
Plastic
Nut
Plastic
Washer
Threaded
Post
Attaching the Camera to the Stand
Attaching the Antenna
Wireless Antenna (WCW100 Only)
Rotate the wireless antenna onto the threaded post to ensure clear wireless
communication. Antenna can be adjusted to obtain a better signal. Best results
are usually obtained by positioning the antenna vertically.
Camera Stand
Install the camera stand to provide a steady base for the camera.
1. Loosen the plastic nut on the back of the camera.
2. Rotate the threaded post upwards.
3. Rotate the camera onto the threaded post until it stops.
4. Tighten plastic washer against camera to secure.
Privacy Button
The privacy button can be used to temporarily suspend video transmission.
Enable Privacy
Press the privacy button. Button will light green when activated.
Disable Privacy
Press the privacy button. Green light will go out when video transmission
resumes.
POWER
NETWORK
Privacy
Button
Privacy Button
Reset Button
ÎUsing the reset button is not recommended.
To change camera setup, follow the steps under Moving the Camera to a
Different Account.
ÎPressing the reset button will restore factory default camera settings.
In most cases, this WILL NOT correct issues with connecting or
viewing the camera.
1. Connect power to camera.
2. Using a small pin, press and hold the reset button for 15 seconds. Then
release the button.
3. LEDs will turn off and then on.
NETWORK
POWER
Do Not
Use
Reset Button
Power, Ethernet and MAC ID
DO NOT connect power and Ethernet until instructed to do so by the web
site, during the enrollment process.
MAC ID is located on the label on the back of the camera.
WPS
POWER
LAN
Speaker
OUT
5V/1A
IC ID: 7954A
WCW100
XXXXXXXXXX
XXXXXXXXXX
Power and Ethernet
WPS Button
DO NOT use the WPS button. Pushing this button may prevent the camera from
enrolling to the LiNK system properly.
If the button is accidentally pushed, power must be disconnected and then
reconnected to the camera before enrolling the camera.
Do Not
Use
IC ID: 7954A
WCW100
XXXXXXXXXX
XXXXXXXXXX
WPS
POWER
LAN
Speaker
OUT
5V/1A
WPS Button

Produkt Specifikationer

Mærke: Schlage
Kategori: Overvågningskamera
Model: WCW100

Har du brug for hjælp?

Hvis du har brug for hjælp til Schlage WCW100 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Overvågningskamera Schlage Manualer

Schlage

Schlage WCO100 Manual

7 April 2025
Schlage

Schlage WCW100 Manual

7 April 2025

Overvågningskamera Manualer

Nyeste Overvågningskamera Manualer

xmartO

xmartO EPS8084 Manual

15 Juni 2025
Tracer

Tracer Guard 4 Manual

15 Juni 2025
Marshall

Marshall CV730-WH Manual

15 Juni 2025
xmartO

xmartO WYS3084 Manual

15 Juni 2025
Sony

Sony SNC-XM632 Manual

15 Juni 2025
Tracer

Tracer Focus 3 Manual

15 Juni 2025
Marshall

Marshall CV605-BK Manual

15 Juni 2025
IDIS

IDIS DC-S6281FX Manual

15 Juni 2025
Marshall

Marshall CV630-NDIW Manual

15 Juni 2025
Marshall

Marshall CV730-ND3W Manual

15 Juni 2025