Schneider MTN630719 Manual

Schneider Bevægelsesdetektor MTN630719

Læs gratis den danske manual til Schneider MTN630719 (10 sider) i kategorien Bevægelsesdetektor. Denne vejledning er vurderet som hjælpsom af 72 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 36.5 anmeldelser. Har du et spørgsmål om Schneider MTN630719, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/10

V6307-561-00 02/08

KNX ARGUS Presence Basic

Operating instructions

Art. no. MTN6307..

– Surface-mounted housing for ARGUS Presence (Art.

no. MTN550619)

¼DANGER

Risk of fatal injury from electrical current.

All work carried out on the unit may only be per-

formed by skilled electricians. Observe the regu-

lations valid in the country of use, as well as the

valid KNX guidelines.

The KNX ARGUS Presence Basic (called ARGUS in the

following) is a KNX presence detector for interior ceiling

mounting.

It detects smaller movements within a circumference of

360° and a radius of 7 m (at a mounting height of 2.5 m).

|The specified ranges refer to average conditions

for the recommended mounting height and are

therefore guide values. The range and sensitivity

can vary greatly when the temperature fluctuates.

When movement is detected, a data telegram defined by

the programming is transmitted and then evaluated to

control the lighting, blinds, or heating, for example.

The ARGUS presence function continuously adjusts for

brightness in the room. If sufficient natural light is avai-

lable, the device will switch the artificial light off even if a

person is present. The overshoot time can be adjusted

using the ETS. The integrated light sensor continually

measures the brightness level and processes this infor-

mation in the application. In addition, it is possible to

measure the brightness with an external light sensor and

have it evaluated.

The device is designed for use in offices, schools, public

buildings or at home, for example. It is intended for cei-

ling mounting in a No. 60 mounting box, and can also be

mounted on the ceiling in the surface-mounted housing

for ARGUS Presence. The ARGUS has an integrated

bus coupler and its power is supplied via KNX.

Accessories

For your safety

ARGUS introduction

|Movement/presence detectors are not suitable

for use as components of an alarm system.

|Movement/presence detectors can trigger false

alarms if the installation site has been chosen un-

favourably.

Movement/presence detectors switch on as soon as

they detect a moving heat source. This can be a person,

but also animals, trees, cars or differences in temperatu-

re in windows. In order to avoid false alarms, the chosen

installation site should be such that undesired heat sour-

ces cannot be detected (see section „Selecting the in-

stallation site“).

AProgramming button

BProgramming LED

CBus connecting terminal

When selecting a suitable installation site, you should

take a number of factors into account so that the ARGUS

operates optimally.

• The shorter the distance between the detected person

and the ARGUS, the better smaller movements are

detected.

• When a person is walking, a larger area of detection is

available. The reference level for the detection is the

floor.

• The mounting height has a direct effect on the range

and sensitivity of the ARGUS. The optimal mounting

height is 2.5 m.

The following diagram shows the ranges of the ARGUS.

They are based on average temperature conditions at a

mounting height of 2.5 m. The range of a movement de-

tector can fluctuate considerably at variable temperatu-

res.

Using ARGUS with alarm systems

Connections, displays and operating

elements

Selecting the installation site

Mounting height Area of detection

2.0 m 11 m

2.5 m 14 m

3.0 m 17 m

14,0 m

2,5 m

• The position of the ARGUS in regard to the direction of

movement also affects detection. If possible, install the

movement detector sideways to the direction of move-

ment.

• If you wish to attach several presence detectors, install

them so that the detection areas of the individual de-

vices intersect each other.

• The ARGUS is designed for permanent installation on-

ly. Mount the ARGUS on a fixed base only to avoid

faulty operation caused by the movement of the detec-

tor.

• To prevent undesired load switching, do not mount the

switched luminaire directly in the detection area of the

ARGUS.

• Avoid mounting the device above a luminaire (e.g.

standard lamp). The heat radiation of the luminaire

can influence the function of the ARGUS. Brightness

can no longer be measured when there is direct light

incidence. If luminaires are mounted in the ARGUS

detection area, a distance of at least 3 m must be com-

plied with when the connection load is high.

1The ARGUS is connected via a bus connecting ter-

minal and snapped onto the retaining ring.

AFlush-mounted installation

BSurface-mounted installation

For flush-mounted installation, the retaining ring inclu-

ded with supply is fixed with two screws to a size 60 in-

stallation box. For surface mounting, the retaining ring is

mounted in the surface-mounted housing which is avai-

lable as an accessory.

1Press the programming button.

The programming LED lights up.

2Load the physical address and application into the

device from the ETS.

The programming LED goes out.

The application has been loaded successfully, the de-

vice is ready for operation.

ARGUS installation

Putting ARGUS into operation

OK OK

A B

V6307-561-00 02/08

If you have technical questions, please contact the Cus-

tomer Care Center in your country.

www.schneider-electric.com

This product must be installed, connected and used in

compliance with prevailing standards and/or installation

regulations. As standards, specifications and designs

develop from time to time, always ask for confirmation of

the information given in this publication.

Technical data

Nominal voltage: DC 24 V (+6 V / -4 V)

KNX connection: Bus connecting terminal

Current consumption: max. 8 mA

Angle of detection: 360°

Number of levels: 6

Number of zones: 136 with 544 switching seg-

ments

Number of

movement sensors: 4

Recommended

mounting height: 2 m - 5 m, optimum 2.50 m

Light sensor: infinitely adjustable in ETS bet-

ween approx. 10 and 2000 lux In

general, the values measured by

the sensor deviate from the ligh-

ting conditions at the main place

of usage (e.g. work surface). The

extent of the deviation is depen-

dent on the installation site of the

sensor, the properties of the

room (reflection of the lumin-

aires, type of paint on the walls

and the surfaces) and the lumin-

aires used.

Range: Radius of approx. 7 m; can be

set in ETS

Overshoot time: from 1 s to 255 hours; can be set

in the ETS

Display elements: 1 red programming LED

Operating elements: 1 programming button

Ambient temperature

Operation: -5 °C to +45 °C

(at temperatures > 30 °C, move-

ment detection is limited)

Storage: -25 °C to +45 °C

Transport: -25 °C to +70 °C

EC guidelines: EMC guideline 89/336/EEC

Initialisation: Due to the limitation of the tele-

gram rate, a telegram cannot be

generated until 20 seconds after

initialisation at the earliest.

Type of protection: IP 20

Schneider Electric Industries SAS

Produkt Specifikationer

Mærke:	Schneider
Kategori:	Bevægelsesdetektor
Model:	MTN630719

Har du brug for hjælp?

Hvis du har brug for hjælp til Schneider MTN630719 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Bevægelsesdetektor Schneider Manualer

Schneider WDE002375 Manual

7 September 2024

Schneider WDE002367 Manual

2 September 2024

Schneider MTN6304-0019 Manual

13 August 2024

Schneider CCT592011 Manual

27 Juli 2024

Schneider CCT591011 Manual

25 Juli 2024

Schneider MTN630719 Manual

25 Juli 2024

Schneider WDE002374 Manual

23 Juli 2024

Schneider CCT595011 Manual

23 Juli 2024

Schneider WDE002959 Manual

8 Juli 2023

Schneider MTN6904-0001 Manual

13 November 2022

Bevægelsesdetektor Manualer

Nyeste Bevægelsesdetektor Manualer

Hikvision DS-TDSB00-EKH Manual

28 Juli 2025

Blaupunkt IR-S1 Manual

28 Juli 2025

Panasonic ST4 Manual

25 Juli 2025

Steinel L 331 S Manual

25 Juli 2025

Steinel MD-8 ECO COM1 Manual

25 Juli 2025

Steinel PD-24 ECO COM1 Manual

25 Juli 2025

Steinel IS 3360 COM1 Manual

25 Juli 2025

Steinel PD-8 ECO COM1 Manual

25 Juli 2025

Steinel IS 3180 COM1 Manual

25 Juli 2025

Vimar 19485.M Manual

24 Juli 2025