Scosche GM1482R Manual

Scosche Ikke kategoriseret GM1482R

Læs gratis den danske manual til Scosche GM1482R (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 4 anmeldelser. Har du et spørgsmål om Scosche GM1482R, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

SHAFT

RADIO

SNAP

SHAFT

TABS

MOUNTING

PANEL

IN-DASH INSTALLATION KIT FOR

1988-94 GENERAL MOTORS

1500 SERIES FULL SIZE TRUCKS

TECH HELP 1-800-621-3695x3

LIABILITY DISCLAIMER

This instruction booklet is based on carefully documented data and research of automobile dash disassembly, wire harness/

codes and information pertaining to installation of this kit (GM1482) in 1988-94 GM Vehicles. Scosche Industries, Inc. can not

be held responsible for discrepancies/inconsistencies that may occur due to the automobile manufacturing changes or

options, or damage that may occur in the automobile during the installation of components while using this booklet.

Vehicle Applications:

CHEVROLET / GMC

1992-94 BLAZER - FULL SIZE

1992-94 CREW CAB DOOLEY PICKUP

1988-94 PICKUP - FULL SIZE

1992-94 SUBURBAN

1992-94 YUKON

GM1482

If you have any further questions, call

NOTE: Scosche MDA-1 antenna adapter

and GM02 factory connector (sold

separately) are needed to

complete the installation.

ILLUSTRATION A

CAUTION:

Disconnect your vehicle's negative battery terminal before the installation to help prevent electrical

Damage. We recommend the use of a volt/ohm meter over a test light to check wiring. A test light or

grounded wire probe can cause damage to the vehicle's computer and/or diagnostic systems. Avoid all

factory air bag wiring - air bags can accidentally deploy causing serious injury or death.

NOTES:

See your vehicle's instructions for any special tools your installation might require. Read all instructions

accompanying your car stereo/cassette player for proper wiring and mounting instructions.

INTRODUCTION/PRELIMINARYINTRODUCTION/PRELIMINARY

INTRODUCTION/PRELIMINARY

FACTORY WIRE CODES

For Factory Wiring Codes go to: www.scosche-cars.com

MOUNTING

SLEEVE

DIN

RADIO

RADIO'S

SUPPLIED

TRIMPLATE

MOUNTING

PANEL

TAPE PLAYER/EQUALIZER REMOVAL

AND CAVITY PREPARATION:

1. Carefully remove the factory bezel by prying out along the bottom to release fastening clips. Then

carefully pull down on the bezel to release the fasteners securing the top and remove the bezel.

2. Extract the two (2) screws securing the factory tape player/equalizer (when equipped).

3. Remove the dash panel under the steering column by extracting the two (2) screws securing it to

the dash.

4. Locate and remove the radio tuner pack under the dash above the acceleator pedal by extracting

the three (3) screws securing it to the dash.

5. Unplug all the connectors going into the radio tuner pack and remove it from the vehicle.

6. Pull the tape player/equalizer from the dash, carefully pull the plug harness through the dash from

the radio tuner pack location and remove the tape player/equalizer from the dash.

7. Locate the antenna plug and the three plugs that were connected to the top of the radio tuner pack.

Route them into the tape player/equalizer cavity. These are the factory power, speaker and antenna

plugs that will be used for the aftermarket radio hook-ups.

DIRECTIONS

ILLUSTRATION C

REAR

VIEW

OF KIT

ILLUSTRATION B

METAL

FASTENING

CLIP

GM1482 KIT PREPARATION:

1. Remove the metal fastening clips from the

bottom of the factory dash bezel and attach

them to the same location on the GM1482

kit. (See Illustration B)

2. Remove the A/C vents from the factory dash

bezel by releasing the spring fastening clips

securing them into the bezel.

3. Mount the vents into the kit by inserting the

inner edge of the vent into the center

alignment slot then insert the outer edge of

the vent into the outer alignment slot. Using

the same spring clips and mounting

procedures that were used to mount the

vents to the factory dash bezel, mount the

vents to the kit.

STEREO INSTALLATION:

1. Install the GM1482 kit into the dash by

inserting the top mounting clips into the slots

in the dash and pushing up to snap them in.

Then press the bottom clips into the slots at

the bottom of the dash to secure the kit to the

dash.

2. Connect the stereo to the factory plugs

(see Wire Codes) as directed in the

stereo installation manual.

3. Mount the stereo into the GM1482 kit as

shown in Illustration C for DIN or

llustration A for shaft.

Produkt Specifikationer

Mærke:	Scosche
Kategori:	Ikke kategoriseret
Model:	GM1482R

Har du brug for hjælp?

Hvis du har brug for hjælp til Scosche GM1482R stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Scosche Manualer

Scosche SUH12V Manual

6 Juni 2025

Scosche Strikeline CR Manual

21 Februar 2025

Scosche ITCFD05AB Manual

21 August 2024

Scosche FT4275B Manual

21 August 2024

Scosche PSM21000 Manual

21 August 2024

Scosche SU2029B Manual

21 August 2024

Scosche IPD2CFBK Manual

21 August 2024

Scosche EFX PA10BX Manual

21 August 2024

Scosche SI-2227B Manual

21 August 2024

Scosche PBJ300 Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vulcan 1024W Manual

15 Juni 2025

Backyard Pro 554PL2030 Manual

15 Juni 2025

Haier 1U18TE2HDA Manual

15 Juni 2025

AEG EWKEXT1 Manual

15 Juni 2025

Planet XGPN-400AXV Manual

15 Juni 2025

Cadac 3 Cook Turbo Manual

15 Juni 2025

Bobrick B-3944 Manual

15 Juni 2025

Sony SZC-4008 Manual

15 Juni 2025

Watts ETX-15 Manual

15 Juni 2025

Sigma REMOTE ONE Manual

15 Juni 2025