Sensative SENE1110 Manual

Sensative Dør / vindue sensor SENE1110

Læs gratis den danske manual til Sensative SENE1110 (1 sider) i kategorien Dør / vindue sensor. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 5 anmeldelser. Har du et spørgsmål om Sensative SENE1110, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Strips are Z-Wave magnet sensors that can be added to any

certified Z-Wave system and operate with any Z-Wave device.

Z-Wave is an international standard for wireless communication

in smart homes and buildings enabling you to monitor and

control your home remotely.

Please follow the three steps in this guide to get started.

1. Add 2. Plan 3. Place

A B

For good communication

Strips uses low power radio signals to communicate with your

Z-Wave controller. For best results, please consider the following:

• Strips are designed to fit invisibly in between most wood,

aluminum, and plastic door and window frames.

• Strips should not be mounted directly on magnetic surfaces

or within a metal structure as the range will be reduced.

• Strips range is up to 40 meters.

• Any non-battery Z-Wave device will act as a repeater to

increase network reliability and range. Usage of repeaters will

reduce Strips’ battery life.

For good functionality in the door or window

• To place Strips invisibly, you need a gap with a minimum

height of 3.5 mm.

• Strips may be mounted on the frame (recommended)

and the magnet on the door/window, or vice versa.

• Check that magnet (A) can be placed so that it is less

than 10 mm from Strips’ flat end when the window is closed.

When the window is open, the magnet should be at least

30 mm away from Strips.

• Open the door/window fully to check that the placement of

Strips and the magnet does not interfere with hinges or

locking mechanisms.

To correctly mount Strips, please follow the steps below:

1. Make sure the surface is clean, dry and at least +10°C(+50°F)

Use the included cloth to clean and prepare the surfaces.

2. Remove the short protective film from the small Strips

test adhesive. The small adhesive is used before the final

placement so it is easy to move Strips if needed.

3. Place Strips where you want it mounted. Check the position

by carefully closing the door/window and then opening it

completely again.

4. Measure and identify where the magnet (A) should be

placed. Remove the protective film and place the magnet.

Close and open again to validate that your Z-Wave

controller detected the changes. Re-mount if needed.

5. When you are satisfied, mark the exact position for Strips.

Remove it from its position, ensure that the surface is still

clean, remove the long film protecting the adhesive backing

and place Strips exactly as you marked. The long adhesive is

used to make the final placement of Strips.

6. Check that the door/window can be fully closed and opened

and that your Z-Wave controller detects the changes.

7. Keep the round magnet (B); since it can be used to wake up,

remove or reset Strips in the future.

More guidance including instructional videos:

www.sensative.com/guard

Strips Guard ENGLISH

ADDPLANPLACE

Wake up

To wake up Strips manually for Z-Wave communication, first place the

round magnet (B) at the rounded edge. When the LED blinks, move the

magnet away. Repeat a total of 3 times within 10 seconds.

Add/remove

Set your controller in add or remove mode (see your controller’s manual).

Follow the instruction above for Wake up. A long LED blink indicates that the

add/remove was successful.

Reset

You may need to reset Strips if your Z-Wave controller is missing or not responding.

Follow the instructions for “Wake up” above, but on the 3rd repetition, leave the

magnet at the rounded edge for 10 seconds. A long LED signal indicates success.

1 short

blink

• User feedback during commands

• Specific event detected (e.g. door opened)*

2 short If Strips is not added

1 long User command successfully executed

5 short Error. e.g. communication with controller failed

No Description Values Default

Notification

type (1 byte)

0: Binary Sensor report

1 : Notification report

2: Basic report

LED indication

(1 byte)

0: Specific event

indication (*) Off

1 : On

Strips are delivered in auto-add mode.

Follow the process below to add Strips to your network.

1. Start the add mode on your Z-Wave controller.

See your controller’s manual.

2. Keep Strips close to its intended location during the add

process. Remove both magnets. 1 long blink confirms the

addition.

3. Your Z-Wave controller application should now be able to

monitor your Strips sensor status.

4. Move the squared magnet (A) away from the squared end.

Check that your Z-Wave system indicates the status

correctly.

5. If your Z-Wave system doesn’t respond, you may need to

change Strips’ notification type from the controller.

Association

Strips supports association group 1 (lifeline), max 1 node,

normally used to send Strips’ status to the Z-Wave controller.

Tamper

Strips will send a tamper alert if it detects that someone tries to wake up or

manipulate Strips.

GBS/INS 11 01 010 R3

A) LED LIGHT SIGNALS

B) CONFIGURATION

C) USER COMMANDSD) OTHER

PARAMETERS

Produkt Specifikationer

Mærke:	Sensative
Kategori:	Dør / vindue sensor
Model:	SENE1110
Bredde:	15 mm
Dybde:	195 mm
Højde:	2.98 mm
Produktfarve:	Hvid
Forbindelsesteknologi:	Trådløs
Batteritype:	LiMnO2
Grænseflade:	Z-Wave
Driftsfrekvens:	868.4 MHz
Antal produkter inkluderet:	1 stk
Omgivelsestemperatur (min):	-20 °C
Omgivelsestemperatur (maks):	60 °C