Senseair eSENSE Ind Disp Manual

Senseair CO2 Sensor eSENSE Ind Disp

Læs gratis den danske manual til Senseair eSENSE Ind Disp (4 sider) i kategorien CO2 Sensor. Denne vejledning er vurderet som hjælpsom af 5 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 3 anmeldelser. Har du et spørgsmål om Senseair eSENSE Ind Disp, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Document

IMA0119

Rev

Page

1 (4)

CO2 transmitter

eSENSE Ind

General

The IAQ-sensor product eSENSE Ind for wall mounting in industrial application are

designed to measure carbon dioxide (CO2). Option -Disp displays the measured CO2

value in ppm (parts-per-million) on the LCD.

The units are designed for connecting to Direct Digital Control (DDC) with 0-10V or

2-10V signal inputs. The two parallel signal outputs Out(1) (0-10V) and Out(2) (2-

10V) give linear signal voltages corresponding to the measuring range.

The 2-10V output also indicates the status by setting the output voltage to 1V or 2

mA when the sensor self-diagnostics detects any error.

Gas and Air Sensors

eSENSE Ind (Disp)

Installation Manual

1 Wall plate

2 PCB (Factory supplied

mounted in box)

3 Hole for wall plate hooks

4 Snap-in lid

5 Locking screw of the lid

(not shown)

6 Air holes

Document

IMA0119

Rev

Page

2 (4)

7 Lidlocking screw

8 Wall plate

9 Screw to hold the wall plate

10 Drill marking for cable entry bushings

Dismounting the wall plate

The sensor is delivered with the wall

plate mounted. The wall plate has to

be removed before the sensor is

mounted onto the wall. Unscrew the

screw on the side of the box.

Wall Mounting Instruction

1) Electrical cable entry: The box has a factory mounted cable entry bushing in

dimension PG9. Never feed more than one cable through each cable entry bushing,

or else gas might leak through!

2) Screw the wall plate onto the wall: The wall plate has holes for three screws.

Drill holes for 3,5mm screws and put dowel into them. Dowels and screws 3,5 x

25mm are included in a plastic bag

3) Attaching the sensor box to the wall plate is done by a snap-in fitting. The wall

plate has three hooks that fit in holes in the sensor box. Fasten the screw on the side

of the box.

4) The lid can be locked with the screw at the bottom of the sensor box.

If for some reason the PCB must be removed it must be handed carefully

and protected from electrostatic discharge! Normally, removing the PCB is

not required.

10 8910

38,5 (1,5) 10 (0,39)

85 (3,35)

141,8 (5,58)

9,5 (0,37)

82(3,23)

66(2,60)

41(1,61)

17,5(0,69)

40,5(1,59)

63(2,48)

Ø5(0,20)

42(1,65)

39,9(1,57)

Produkt Specifikationer

Mærke:	Senseair
Kategori:	CO2 Sensor
Model:	eSENSE Ind Disp

Har du brug for hjælp?

Hvis du har brug for hjælp til Senseair eSENSE Ind Disp stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

CO2 Sensor Senseair Manualer

Senseair eSENSE Ind Disp Manual

24 August 2024

Senseair tSENSE VAV Disp Manual

22 August 2024

Senseair tSENSE Disp Manual

21 August 2024

Senseair aSENSE Duct Manual

18 August 2024

Senseair Explora PM2.5 Manual

10 August 2024

Senseair aSENSE VAV Manual

9 August 2024

Senseair eSENSE Disp Manual

7 August 2024

Senseair aSENSE GH Manual

4 August 2024

Senseair aSENSE M III Manual

3 August 2024

Senseair eSENSE II Manual

2 August 2024

CO2 Sensor Manualer

Nyeste CO2 Sensor Manualer

Zehnder CO2-Sensor CO2 Sensor Manual

2 September 2024

Brink Climate CO2- sensor Manual

25 August 2024

Duco CO2-sensor Z-wave Manual

25 August 2024

EnviSense CO2 Monitor Manual

24 August 2024

Duco RH sensor Z-wave Manual

24 August 2024

Duco Comfort System - Plus Wired Manual

24 August 2024

Duco RF-C bedieningsschakelaar Manual

23 August 2024

Bresser 7004040 CO2 Air Quality Monitor Manual

21 August 2024

Orcon CO2 ruimtesensor 15RF Manual

18 August 2024

TechGrow T-1 Manual

10 August 2024