Sevenoak SK-LM7 Manual

Sevenoak Ikke kategoriseret SK-LM7

Læs gratis den danske manual til Sevenoak SK-LM7 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Sevenoak SK-LM7, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

SK-LM7

7”On-camera monitor

Before using the product,please read this manual carefully.

Keep this manual safety in case you need to check during your usage.

Operate this product on base of your full understand of this manual.

Speciﬁcations subject to change without notice.

For more information,please visit www.sevenoak.biz

Standard shoe adapter *1

US standard Battery charger

7” monitor

HDMI cable

Sun shade

Manual

Attach the shoe adapter to the 1/4” screw hole

at the bottom of the monitor and lock it by rotating

the adapter clockwise.

Screw A: Shoe adapter and monitor locking screw, rotate it clockwise

to lock the shoe adapter and monitor.

Screw B: Angle adjusting screw, rotate it clockwise to lock, anti-

clockwise to loose.

Screw C: Shoe adapter locking screw, rotate it anti-clockwise to lock

and clock wise to loose.

Compatible battery: Sony NP-F550, NP-F570, NP-F330, NP-F530.

Push the batttery gently as the direction shown in the picture, slide it down till the

click, the battery is ﬁxed into place.To release the battery, slide the battery out.

Slider down to install

the battery

Battery installed

properly

Insert the sun shade to the left and right

buckle kit, make sure the sun shade is ﬁxed

properly.

After attaching the shoe adapter to the monitor, mount the shoe adapter to the camera hot shoe,

then lock the shoe adapter by rotating the shoe adapter locking screw C.

Loosen angle adjusting screw B, users

can adjust the monitor to a desired

position,then lock the angle adjusting

screw.

Power supply:

1. Compatible Sony battery

2. DC power supply, supports US standard adapter and Europe

standard adapter.

Battery charge:

1. Use Sony battery charger

2. Use the power adapter to supplement the battery charge

① Power indicator:

Green: working state

Red: standby

② Power on/o

Press it turn on the monitor,

Press it again to turn o the monitor

③ Input selection switch

HDMI/video1/video2/YPbPr

④ Left button: Press it to move left a menu page

⑤ Up button: Press it to move up a menu item

⑥ Menu/Enter button: Press it to show menu, or conﬁrm

a menu item

⑦ Down button: Press it to move down a menu item

⑧ Right button: Press it to move right a menu page

⑨ Component Y jack

⑩ Component Pb jack

⑪ Component Pr jack

⑫ HDMI jack

⑬ Video 1 input

⑭ Video 2 input

① ② ③ ④⑤

⑥

⑦ ⑧

⑨

⑩

⑪

⑫

⑬

⑭

■　Please read and follow these instructions, and keep this

manual in a safe place.

■　Handle the unit with care.

■　Clean the unit with a soft, dry cloth.

■　Use only parts provided by the manufacturer.

■　Make sure everything is secure before proceeding.

■　Make sure the item is intact and that there are no

missing parts.

■　All photos are for illustrative purposes only.

Sevenoak provides a limited warranty that this product is free

from defects in materials and workmanship to the original

purchaser under normal use for a period of one (1) year from

the original purchase date or thirty (30) days after replacement

(the “Warranty Period”), whichever occurs later. Our responsibility

with respect to this limited warranty shall be limited solely to

repair or replacement, at its option, of any product which fails

during normal consumer use.

To obtain warranty coverage during the Warranty period,

contact your place of purchase (”Seller”) to obtain a return

merchandise authorization (”RMA”) number, and return to

Seller the defective product along with proof of purchase and

the RMA number.

This warranty does not extend to damage or failure which results

from misuse, neglect, accident, alternation, abuse, improper

installation or maintenance. EXCEPT AS PROVIDED HEREIN,

SEVENOAK MAKES NEITHER ANY EXPRESS WARRANTIES

NOR ANY IMPLIED WARRANTIES, INCLUDING BUT NOT

LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY

OR FITNESS FOR A PARTICULAR PURPOSE. This warranty

provides you with speciﬁc legal rights, and you may also have

additional rights which vary from state to state.

Install the battery/DC power supply, the LED indicator turns to Red,

Press button, the monitor is power-on, the LED indicator turns

to green. Press the the power switch for 2 seconds , the LED

indicator turns to Red, the monitor is power-o.

When the monitor is on, press the input signal selection button, enter

into the input signal selection menu: YPbPr, HDMI, Video 1 or Video 2.

Press up/down button to select the input signal, then press button

to conﬁrm.

Before setting the menu functions, please make sure the device is

connected correctly. Turn the power (lower right corner of the unit)

dial to ON position.The monitor enters into working state. After

enter into working state, press the button on the unit, according

to select input video signal to switch “YPbPr, HDMI,Video 1,Video 2”

(under NO menu state, using the shortcut button on the panel to

operate). Press button on the unit, then enter into OSD menu

operation. Press or to move left or right a menu page (Picture/

Sound/Time/Options).

After selecting a menu page, press or to select menu

item, presss to enter into submenu, using or to Change the

value of the selected menu item, then press M to conﬁrm. If you need

to exit OSD menu, press button again.

Picture

1.Picture Mode: Standard (default), Mild, User, Dynamic

2.Color Temperature: Medium (default), Warm, User, Cool

3.Aspect Ratio: Auto (default), 4:3, 16:9, Zoom1, Zoom2, Just scan

(Panorama)

4.Noise Reduction: O, low, Middle, High, Default (default)

5.Back light: 0-100

Sound

Not applicable

Time

1. Clock: Date, Month, Year, Hour, Minute

2. O time: O (default), Once, Every day, Monday to Friday, Monday

to Saturday, Saturday to Sunday, Sunday

3. On time: O (default), Once, Every day, Monday to Friday, Monday t

o Saturday, Saturday to Sunday, Sunday

4. Sleep time: O (default), 10min, 20min, 30min, 60min, 90min,120min,

180min,240min

5. Auto sleep: On, O (default)

Option

1. OSD language: Multi-language is optional, Default is English

2. Color range: 0-255 (Default), 16-235

3. Blending low: O, Low, Middle,, High (default)

4. OSD duration: O, 5sec, 10sec, 15sec

Other options are not aplicable in this product.

Model No. SK-LM7 Power supply

Screen 7” IPS TFT-

LCD Language

Aspect ratio 16:9/4:3/etc Input power

voltage range

Resolution

(WVGA) 800*480 Total current 250mA

Brightness 400cd/ m Power

consumption 3W

Viewing

Angle 50/70/70/70 Input signal HDMI YPbPr、、

Video1 Video2、

Weight 400g

Size (LWH) 192mm*150mm

*25mm

DV 9V

Multilanguage

Lithium battery

or DC adapter

2016 Sevenoak lnc.Visit us on the

web at www.sevenoak.biz

Components Install the shoe adapter

Attaching to the camera Power supply

Identifying the parts

Install the battery Install the sun shade

Limited One-year Warranty Warnings

On/o

Select input signal

Menu operating instruction

Menu operating instruction Menu operating instruction Speciﬁcations

Produkt Specifikationer

Mærke:	Sevenoak
Kategori:	Ikke kategoriseret
Model:	SK-LM7
Bredde:	192 mm
Dybde:	25 mm
Højde:	150 mm
Vægt:	400 g
Produktfarve:	Sort
Strøm:	0.25 A
Skærm diagonal:	7 "
Skærmopløsning:	800 x 400 pixel
Berøringsskærm:	Ingen
Skærmteknologi:	LCD
Skærmens lysstyrke:	400 cd/m²
Antal HDMI-porte:	1
Strømforsyningstype:	Batteri/DC
Strømforbrug (maks.):	3 W
Indgangsspænding:	9 V
Billedformat:	4:3, 16:9