Sharp DT-400 Manual

Sharp videoprojektorer DT-400

Læs gratis den danske manual til Sharp DT-400 (68 sider) i kategorien videoprojektorer. Denne vejledning er vurderet som hjælpsom af 30 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 15.5 anmeldelser. Har du et spørgsmål om Sharp DT-400, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/68

-1

ENGLISH

Before using the projector, please read this operation manual carefully.

WARNING: High brightness light source. Do not stare into the beam of light, or view directly. Be especially

careful that children do not stare directly into the beam of light.

WARNING: To reduce the risk of fire or electric shock, do not expose this product to

rain or moisture.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER.

NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient magnitude

to constitute a risk or electric shock to

persons.

The exclamation point within a triangle is

intended to alert the user to the presence of

important operating and maintenance

(servicing) instructions in the literature

accompanying the product.

Introduction

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT REMOVE SCREWS

EXCEPT SPECIFIED USER

SERVICE SCREW.

See bottom of projector.

IMPORTANT

For your assistance in reporting the loss or theft of your

Projector, please record the Serial Number located on

the bottom of the projector and retain this information.

Before recycling the packaging, please ensure that you

have checked the contents of the carton thoroughly

against the list of “Supplied accessories” on page 5.

Model No.: DT-400

Serial No.:

There are two important reasons for prompt warranty registration of your new SHARP Projector, using

the REGISTRATION CARD packed with the projector.

1. WARRANTY

This is to assure that you immediately receive the full benefit of the parts, service and labor

warranty applicable to your purchase.

2. CONSUMER PRODUCT SAFETY ACT

To ensure that you will promptly receive any safety notification of inspection, modification, or

recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE

READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE. U.S.A. ONLY

WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not

expressly approved by the manufacturer could void the user’s authority to operate this equip-

ment. U.S.A. ONLY

INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the operation manual, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help. U.S.A. ONLY

-2

Caution Concerning Lamp Replacement

See “Replacing the Lamp” on page 56.

LAMP REPLACEMENT WARNING :

TURN OFF THE LAMP AND DISCONNECT

POWER CORD BEFORE OPENING THIS

COVER. HOT SURFACE INSIDE.

ALLOW 1 HOUR TO COOL BEFORE REPLACING THE LAMP.

REPLACE WITH SAME SHARP LAMP UNIT MODEL

AN-K2LP ONLY.

HIGH PRESSURE LAMP :

RISK OF EXPLOSION.

POTENTIAL HAZARD OF GLASS PARTICLES IF LAMP HAS

RUPTURED. HANDLE WITH CARE. SEE OPERATION MANUAL.

SERVICEMAN-WARNING :

USE RADIATION EYE AND

SKIN PROTECTION DURING SERVICING.

AVERTISSEMENT CONCERNANT LE

REMPLACEMENT DE LA LAMPE :

ETEINDRE LA LAMPE ET DEBRANCHER LE CORDON

D’ALIMENTATION AVANT D’OUVRIR LE COUVERCLE.

L’INTERIEUR DU BOITIER ETANT EXTREMEMENT CHAUD,

ATTENDRE 1 HEURE AVANT DE PROCEDER AU

REMPLACEMENT DE LA LAMPE. NE REMPLACER QUE

PAR UNE LAMPE SHARP DE MODÈLE AN-K2LP.

LAMPE A HAUTE PRESSION :

RISQUE

D’EXPLOSION. DANGER POTENTIEL DE PARTICULES DE

VERRE EN CAS D’ECLATEMENT DE LA LAMPE.

A MANIPULER AVEC PRECAUTION.

SE REPORTER AU MODE D’EMPLOI.

AVERTISSEMENT – REPARATEUR :

SE PROTEGER LES

YEUX ET LA PEAU DES RADIATIONS LORS DES REPARATIONS.

PRODUCT DISPOSAL

This projector utilises tin-lead solder, and a pressurised lamp containing a small amount of mercury. Disposal of

these materials may be regulated due to environmental considerations. For disposal or recycling information,

please contact your local authorities or, if you are located in the United States of America, the Electronic Industries

Alliance: www.eiae.org .

Declaration of Conformity

SHARP PROJECTOR, MODEL DT-400

This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device

may not cause harmful interference, and (2) this device must accept any interference received, including interference

that may cause undesired operation.

Responsible Party:

SHARP ELECTRONICS CORPORATION

Sharp Plaza, Mahwah, New Jersey 07430

TEL: 1-800-BE-SHARP (1-800-237-4277) U.S.A. ONLY

WARNING:

The cooling fan in this projector continues to run for about 90 seconds after the projector enters the standby mode.

During normal operation, when putting the projector into standby mode always use the STANDBY button on the

projector or on the remote control. Ensure the cooling fan has stopped before disconnecting the power cord.

DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD.

FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.

Produkt Specifikationer

Mærke:	Sharp
Kategori:	videoprojektorer
Model:	DT-400

Har du brug for hjælp?

Hvis du har brug for hjælp til Sharp DT-400 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

videoprojektorer Sharp Manualer

Sharp X171Q-W Manual

27 Januar 2025

Sharp X171Q-B Manual

27 Januar 2025

Sharp P721Q Manual

18 Oktober 2024

Sharp XG-PH80XN Manual

28 Marts 2024

Sharp PG-D3050W Manual

6 Marts 2024

Sharp XG-NV4SE Manual

2 Marts 2024

Sharp XG-NV3XE Manual

28 Februar 2024

Sharp PGD50X3D Manual

19 Januar 2024

Sharp XG-P610X Manual

8 Januar 2024

Sharp XG-C330X Manual

24 December 2023

videoprojektorer Manualer

Nyeste videoprojektorer Manualer

Acer DX227 Manual

30 Juli 2025

Acer LU-P500UT Manual

30 Juli 2025

30 Juli 2025

30 Juli 2025

30 Juli 2025

30 Juli 2025

30 Juli 2025

30 Juli 2025

30 Juli 2025

30 Juli 2025