Shimano CT-S510 Manual

Shimano Cykeltilbehør CT-S510

Læs gratis den danske manual til Shimano CT-S510 (1 sider) i kategorien Cykeltilbehør. Denne vejledning er vurderet som hjælpsom af 72 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 36.5 anmeldelser. Har du et spørgsmål om Shimano CT-S510, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Technical Service Instructions

General Safety Information

This product cannot be used with coaster brake-type products.

This product is for single front chainwheels only.

Periodically clean the chain tensioner and lubricate the pulley.

If there is a large amount of play in the pulley and an abnormal amount of

noise is generated while riding, replace the pulley unit.

Do not disassemble the pulley unit.

If the tension applied is too strong, noise may be generated while riding.

If the chain becomes elongated and excessive looseness occurs, readjust the

chain tension.

Parts are not guaranteed against natural wear or deterioration resulting from

normal use.

For any questions regarding methods of handling or maintenance, please

contact the place of purchase.

NOTE:

Chain Chain tool

Reinforced

connecting

9-speed super narrow

chain such as

CN-7701/ CN-HG93

8- /7-/ 6-speed narrow

chain such as

CN-HG50/ CN-IG51

Silver

6.5 mm

Black

TL-CN31/

TL-CN22

TL-CN31/

TL-CN22

and

TL-CN30/

TL-CN21

Sprocket

CS-S500

18T/20T

(t = 2.0 mm)

16T – 23T

(t = 2.3 mm)

End pin Link pin Reinforced connecting pin

Move

Upward

direction

Downward

direction

Use neutral detergent to clean the chain. Do not use alkali-based or acid-

based detergents such as rust cleaners, as they may result in damage

and/or failure of the chain.

Use the reinforced connecting pin only for connecting the narrow type of

chain.

There are two different types of reinforced connecting pins available. Be

sure to check the table below before selecting which pin to use.

If connecting pins other than reinforced connecting pins are used, or if a

reinforced connecting pin or tool which is not suitable for that type of

chain is used, sufficient connection force may not be obtained, which

could cause the chain to break or fall off.

If it is necessary to adjust the length of the chain due to a change in the

number of sprocket teeth, make the cut at some other place than the

place where the chain has been joined using a reinforced connecting pin

or an end pin.

The chain will be damaged if it is cut at a place where it has been joined

with a reinforced connecting pin or an end pin.

Check that the tension of the chain is correct and that the chain is not

damaged.

If the tension is too weak or the chain is damaged, the chain should be

replaced. If this is not done, the chain may break and cause serious

injury.

Obtain and read the service instructions carefully prior to installing

the parts. Loose, worn, or damaged parts may cause serious injury to

the rider.

We strongly recommend only using genuine Shimano replacement parts.

Read these Technical Service Instructions carefully, and keep them in a

safe place for later reference.

WARNING – To avoid serious injuries:

Be sure to read these service instructions in conjunction with the service

instructions for the internal 7-speed /8-speed hubs before use.

Chain length

One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003

Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222

3-77 Oimatsu-cho, Sakai-ku, Sakai, Osaka 590-8577, Japan

Jun. 2009 by Shimano Inc. PIT. SZK. Printed in Japan

Please note: Specifications are subject to change for improvement without notice. (English)

Mount the chain onto the chainring and the sprocket, and then adjust the length of the

chain by adding two links, or four links at a maximum.

Mount the chain onto the sprocket, and then set the hub axle into the dropouts.

Installation to the frame

Place the CT-S510 bracket onto the right side of the hub axle, and place the non-

turn washer onto the left side of the hub axle. At this time, turn the cassette joint so

that the projecting parts of the bracket and non-turn washer fit into the grooves of

the dropouts. If this is done, the cassette joint can be installed so that it is almost

parallel to the chainstay.

(Loosen the arm fixing bolt at this time so that the pulley does not interfere with

other parts such as the frame.)

Loosen the chain line adjustment screw.

Adjustment of the chain line

Mount the chain onto the pulley, and then turn the arm upward so that there is 15 –

25 mm of slackness in the chain when tension is being vertically applied to the chain.

(If tension cannot be applied to the chain

in the upward direction, apply the

tension in the downward direction

instead. If tension cannot be applied in

either the upward or downward direction,

add two links to the chain and apply the

tension in the downward direction.)

Adjustment of the chain tension

Move the pulley sideways until the sprocket and pulley

are in a straight line.

Tighten the chain line adjustment screw to secure the

pulley.

Tighten the arm fixing bolt to secure the

arm.

Turn the crank arm and check that the

wheel turns smoothly with no abnormal

noise.

Place the accessory 2 mm spacer onto the right side (outside of the chain

tensioner), and then secure the wheel to the frame with the cap nuts.

(Recommended tightening torque: 30 – 45 N·m {300 – 450 kgf·cm})

Adjust so that there is 15 – 25 mm

of slackness in the chain when a

force of about 100 g is applied.

SI-50F0A-002

7.1 mm

Applicable hubs

Applicable sprockets

Applicable dropout width

Applicable dropout shape

Internal 7-speed / 8-speed

16T – 23T

4 – 9 mm

Vertical

Non-turn washer

(8L)

Cassette joint

Groove of dropout

CT-S510 bracket

Spacer

(right side

only)

Arm fixing bolt

Chainstay

Chain line adjustment screw

Sprocket

Pulley

Arm fixing bolt

Tightening torque:

12 – 14 N·m

{120 – 140 }kgf·cm

Tightening torque:

1 – 2 N·m

{10 – 20 }kgf·cm

Adjust so that there is 15 – 25 mm

of slackness in the chain when a

force of about 100 g is applied.

* Service Instructions in further languages are available at:

http://techdocs.shimano.com

CT-S510 Chain Tensioner

SI-50F0A-002-00

Produkt Specifikationer

Mærke:	Shimano
Kategori:	Cykeltilbehør
Model:	CT-S510

Har du brug for hjælp?

Hvis du har brug for hjælp til Shimano CT-S510 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Cykeltilbehør Shimano Manualer

Shimano RD-F800-GS Manual

7 Maj 2024

Shimano PD-M424 Manual

9 April 2024

Shimano RD-4700-GS Manual

6 April 2024

Shimano FD-4603-B Manual

2 April 2024

Shimano FD-M7025-11-L Manual

30 Marts 2024

Shimano FD-M7025-11-E Manual

26 Marts 2024

Shimano PD-M520 Manual

22 Marts 2024

Shimano CT-S510 Manual

14 Marts 2024

Shimano SL-A050-LN Manual

7 Marts 2024

Shimano FD-M6020-E Manual

29 Februar 2024

Cykeltilbehør Manualer

Nyeste Cykeltilbehør Manualer

Lezyne ABS Pro Clik Chuck Manual

17 December 2025

Vevor TX-SS-03 Manual

1 December 2025

Vevor J900 Manual

23 November 2025

Alpcour APC-BTSMBK Manual

12 November 2025

Prophete 8046 Manual

5 Oktober 2025

Prophete 8166 Manual

4 Oktober 2025

Lazer Urbanize Manual

13 September 2025

Be Cool BC-PP2508 Manual

9 September 2025

Joovy Noodle Manual

9 September 2025

Topeak DEFENDER iGLOW Manual

23 August 2025