Shimano FD-4600-F Manual

Shimano Cykeltilbehør FD-4600-F

Læs gratis den danske manual til Shimano FD-4600-F (1 sider) i kategorien Cykeltilbehør. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Shimano FD-4600-F, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

(3) After trimming, use the outer casing

adjustment barrel to adjust the

clearance between the chain and

chain guide to the minimum (0 - 0.5

mm).

Adjustment is possible at the dual

control lever (with cable adjuster).

For details on the adjustment

method, refer to the Service

Instructions for the ST-4600.

General Safety Information

• Obtain and read the service instructions carefully prior to installing the parts.

Loose, worn or damaged parts may cause the bicycle to fall over and serious injury

may occur as a result. We strongly recommend only using genuine Shimano

replacement parts.

• Obtain and read the service instructions carefully prior to installing the parts.

If adjustments are not carried out correctly, the chain may come off and this may

cause you to fall off the bicycle which could result in serious injury.

• Be careful not to let the cuffs of your clothes get caught in the chain while riding,

otherwise you may fall off the bicycle.

• Read these Technical Service Instructions carefully, and keep them in a safe place for

later reference.

Note

• If gear shifting operations cannot be carried out smoothly, clean the derailleur and

lubricate all moving parts.

• If the amount of looseness in the links is so great that adjustment is not possible, you

should replace the derailleur.

• When the chain is in the position shown in the illustration,

the chain may contact the front chainrings or front derailleur

and generate noise. If the noise is a problem, shift the chain

onto the next-larger rear sprocket or the one after.

• For smooth operation, use the specified outer casing and

the bottom bracket cable guide.

• Grease the inner cable and the inside of the outer casing

before use to ensure that they slide properly.

• Parts are not guaranteed against natural wear or deterioration resulting from normal

use.

• For maximum performance we highly recommend Shimano lubricants and

maintenance products.

• For any questions regarding methods of installation, adjustment, maintenance or

operation, please contact a professional bicycle dealer.

WARNING

Front

chainrings

Rear

sprockets

2. The level section of the chain guide outer plate should be

directly above and parallel to the largest chainring.

3. Secure using a 5mm Allen key.

Chainwheel

(largest chainring)

Chain guide

Tightening torque:

5 - 7 N·m

{44 - 60 in. lbs.}

Tighten the top adjustment screw clockwise

(about 1/4 turn).

Loosen the top adjustment screw

counterclockwise (about 1/8 turn).

Loosen the low adjustment screw

counterclockwise (about 1/8 turn).

Tighten the low adjustment screw clockwise

(about 1/8 turn).

Turn the outer casing adjustment barrel

clockwise (1/8 of a turn at a time) until

shifting to the small chainring becomes

smooth. Be careful not to turn the outer

casing adjustment barrel too far at this time,

otherwise shifting to the large chainring will

become more difficult.

1. Adjust so that the clearance between the chain guide outer

plate and the large gear is 1 - 3 mm before installing.

Technical Service Instructions SI-5MW0A-002

SIS adjustment

1. Low adjustment

Set so that the clearance between the chain guide inner

plate and the chain is 0 - 0.5 mm.

Largest

sprocket Inner chainring

Be sure to read these service instructions in conjunction with the service instructions for the

ST-4600 / ST-5700 / ST-6700 / SL-4600 before use.

4. Top adjustment

Set so that the clearance between the chain guide outer

plate and the chain is 0 - 0.5 mm.

2. Connection and securing of cable

While pulling the inner cable, tighten the wire fixing

bolt with a 5 mm allen key to secure the cable.

While turning the crank arm, gently operate lever (b) and check that the front derailleur

moves slightly toward the small chainring. If the front derailleur moves by a large

amount and the chain is set onto the small chainring at this time, loosen the top

adjustment bolt by 1/8th of a turn. Then, after returning the chain to its original position,

adjust and check the trimming mechanism.

Smallest

sprocket Outer chainring

Low adjustment

screw

Chain guide

inner plate

Chain

Pull

Tightening torque:

6 - 7 N·m {52 - 60 in. lbs.}

After taking up the initial slack in

the cable, re-secure to the front

derailleur as shown in the

illustration.

3. Adjustment of the cable tension

(1) When making the cable

adjustment, place the chain on

the largest sprocket at the rear;

and at the front, shift the chain to

the inner chainring and then set

it back onto the outer chainring.

Note:

There are two derailleur positions for the outer chainring. Make sure the derailleur is in

the inner side of the two positions.

Shift the derailleur from the inner chainring (L)

to the outer chainring (T), then gently press

the small lever (b) until a small click is felt.

(trim function).

(2) Perform the trimming.

(ST-4600 / ST-5700 / ST-6700)

Top adjustment

screw

Chain guide

outer plate

Chain

■Trimming (noise-prevention mechanism)

Gently press the lever [

(A “click” sound will be heard.)

Chain guide

inner plate

Chain

FD-CX70

FD-4600

FD-4600 FD-CX70

Clearance:

0 - 0.5mm

Outer casing

adjustment barrel

Largest

sprocket Outer chainring

Largest

sprocket Outer chainring

Front shifting

Lever [

From large chainring

to small chainring

Lever [

From small chainring

to large chainring

Adjustment point

Lever [

Type Band type / Brazed on type

Front derailleur installation band diameter S (28.6mm), M (31.8mm), L (34.9mm)

Chainstay angle (C) FD-4600 (61° - 66°), FD-CX70 (63° - 66°)

Front chainwheel tooth difference 16 teeth or less

Chain line 43.5mm

Installation of the front derailleur

Clearance: 1 - 3 mm

Chain guide outer plate

Specifications

5. Troubleshooting chart

After completion of steps 1 - 4, move the shifting lever to check the shifting.

(This also applies if shifting becomes difficult during use.)

If the chain falls to the crank side

If shifting is difficult from the small chainring to the

large chainring

If shifting is difficult from the large chainring to the

small chainring

If the chain falls to the bottom bracket side.

If the gear shifting to the small chainring is stiff and

difficult to carry out after trimming.

SI-5MW0A-002-00

One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003

Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222 3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan

* Service Instructions in further languages are available at : http://techdocs.shimano.com

Please note: specifications are subject to change for improvement without notice. (English)

FD-4600

FD-CX70 Front derailleur

In order to realize the best performance, we recommend that the following

combination be used.

Series

Dual control lever

Shifting lever

Brake lever

Outer casing

Gears

Front derailleur

Front chainwheel

Rear derailleur

Freehub

Cassette sprocket

Chain

Bottom bracket cable guide

TIAGRA

ST-4600

SL-4600

BL-4600

OT-SP41

FD-4600

FC-4600 / FC-4650

RD-4600-SS

FH-4600

CS-4600

CN-4601

SM-SP17

Non series (Cyclo-cross)

ST-6700 / ST-5700

–

OT-SP41

FD-CX70

FC-CX70 / FC-CX50

RD-6700 / RD-5700

FH-6700 / FH-5700

CS-6700 / CS-5700

CN-6701 / CN-5701

SM-SP17

Produkt Specifikationer

Mærke:	Shimano
Kategori:	Cykeltilbehør
Model:	FD-4600-F

Har du brug for hjælp?

Hvis du har brug for hjælp til Shimano FD-4600-F stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Cykeltilbehør Shimano Manualer

Shimano RD-F800-GS Manual

7 Maj 2024

Shimano PD-M424 Manual

9 April 2024

Shimano RD-4700-GS Manual

6 April 2024

Shimano FD-4603-B Manual

2 April 2024

Shimano FD-M7025-11-L Manual

30 Marts 2024

Shimano FD-M7025-11-E Manual

26 Marts 2024

Shimano PD-M520 Manual

22 Marts 2024

Shimano CT-S510 Manual

14 Marts 2024

Shimano SL-A050-LN Manual

7 Marts 2024

Shimano FD-M6020-E Manual

29 Februar 2024

Cykeltilbehør Manualer

Nyeste Cykeltilbehør Manualer

Nils Extreme MTW291 Manual

9 Juni 2025

Abus PowerDome Manual

9 Juni 2025

Racktime Mia Manual

30 Marts 2025

Racktime 13035 Manual

29 Marts 2025

Racktime 13012 Manual

29 Marts 2025

Racktime 13014 Manual

29 Marts 2025

Racktime 13008 Manual

29 Marts 2025

Racktime 13007 Manual

29 Marts 2025

Racktime Lightit Manual

29 Marts 2025

Racktime Foldit Manual

29 Marts 2025