Shimano SL-3S35E Manual

Shimano Cykeltilbehør SL-3S35E

Læs gratis den danske manual til Shimano SL-3S35E (2 sider) i kategorien Cykeltilbehør. Denne vejledning er vurderet som hjælpsom af 39 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 20 anmeldelser. Har du et spørgsmål om Shimano SL-3S35E, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Shifting Lever

(Internal Geared Hub

3-Speed)

IMPORTANT NOTICE

•Contact the place of purchase or a distributor for information on installation,

adjustment, and replacement of the products which are not found in the user's

manual. A dealer's manual for professional and experienced bicycle mechanics is

available on our website (https://si.shimano.com).

For safety, be sure to read this “user's manual” thoroughly

before use, follow it for correct use, and store it so that it

can be referenced at any time.

The following instructions must be observed at all times in order to prevent

personal injury and physical damage to equipment and surroundings. The

instructions are classified according to the degree of danger or damage which may

occur if the product is used incorrectly.

DANGER Failure to follow the instructions will result in

death or serious injury.

WARNING Failure to follow the instructions could result in

death or serious injury.

CAUTION

Failure to follow the instructions could cause

personal injury or physical damage to equipment

and surroundings.

Important Safety Information

WARNING

•Do not disassemble or modify the product. This may cause the product to not

operate correctly, and you may suddenly fall and be seriously injured.

CAUTION

•Be sure to push in the shifting lever until you feel a click with a clicking sound to

shift one gear at a time. During shifting, reduce the force being applied to the

pedals. If you try to force operation of the shifting lever or perform multishifting

while the pedals are being turned strongly, your feet may come off the pedals

and the bicycle may topple over, which could result in serious injury. Operating

the shifting lever to multi-shift to a light gear may also cause the outer casing to

spring out of the shifting lever. This does not affect the capabilities of the shifting

lever because the outer casing returns to the original position after shifting.

•Never place your foot on the bell crank. Otherwise, gear shifting may not

function properly.

Notice

•Products are not guaranteed against natural wear and deterioration from normal

use and aging.

•For maximum performance we highly recommend Shimano lubricants and

maintenance products.

Regular Inspections Before Riding the Bicycle

Before riding the bicycle, check the following items. If any problems are found,

consult your place of purchase or a distributor.

•Is gear shifting carried out smoothly?

•Are the setting lines of the cassette joint in the correct position?

•Is the bell crank push rod in the correct position?

•Do any abnormal noises occur during operation?

Names of parts

The components differ according to the specifications of the internal geared hub.

Cassette joint

Bell crank

Shifting lever (RAPIDFIRE PLUS)

Shifting lever

(piano touch lever)

Shifting lever

(REVOSHIFT)

Inspection method for cable adjustment

For the cassette joint

Set the shifting lever to [2]. Check that the yellow setting lines on the cassette joint

bracket and pulley overlap. If the overlapping area falls short of two thirds of each

setting line, consult your place of purchase or a distributor. Riding the bicycle with

the setting lines misaligned may cause the gears to not engage properly during

pedaling, causing abnormal noise or free spinning of the pedals.

Set to [2] Set to [2] Set to [2]

Yellow setting line

Bracket Pulley

Should be aligned

When the bicycle is upright

The yellow setting lines on the cassette joint are located in two places;

above and below. Use the one that is easier to see.

The overlapping area falls short of two

thirds of each setting line

For the bell crank

Set the shifting lever to [2].

Set to [2] Set to [2] Set to [2]

Push rod

End of hub axle

Yellow line

Yellow part of link

Line on push rod

Note:

When checking, look at the two

yellow lines on the window directly

from above.

Make sure that the line on push rod is aligned with the end of the hub

axle.

If the line on push rod cannot be seen, conﬁrm that the yellow part of

the link is between the two yellow lines on the window.

Yellow line

UM-6P20A-002 User's manual

Produkt Specifikationer

Mærke:	Shimano
Kategori:	Cykeltilbehør
Model:	SL-3S35E

Har du brug for hjælp?

Hvis du har brug for hjælp til Shimano SL-3S35E stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Cykeltilbehør Shimano Manualer

Shimano RD-F800-GS Manual

7 Maj 2024

Shimano PD-M424 Manual

9 April 2024

Shimano RD-4700-GS Manual

6 April 2024

Shimano FD-4603-B Manual

2 April 2024

Shimano FD-M7025-11-L Manual

30 Marts 2024

Shimano FD-M7025-11-E Manual

26 Marts 2024

Shimano PD-M520 Manual

22 Marts 2024

Shimano CT-S510 Manual

14 Marts 2024

Shimano SL-A050-LN Manual

7 Marts 2024

Shimano FD-M6020-E Manual

29 Februar 2024

Cykeltilbehør Manualer

Nyeste Cykeltilbehør Manualer

Lezyne ABS Pro Clik Chuck Manual

17 December 2025

Vevor TX-SS-03 Manual

1 December 2025

Vevor J900 Manual

23 November 2025

Alpcour APC-BTSMBK Manual

12 November 2025

Prophete 8046 Manual

5 Oktober 2025

Prophete 8166 Manual

4 Oktober 2025

Lazer Urbanize Manual

13 September 2025

Be Cool BC-PP2508 Manual

9 September 2025

Joovy Noodle Manual

9 September 2025

Topeak DEFENDER iGLOW Manual

23 August 2025