Siemens Landis & Staefa REV11 Manual

Siemens Termostat Landis & Staefa REV11

Læs gratis den danske manual til Siemens Landis & Staefa REV11 (2 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om Siemens Landis & Staefa REV11, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Operating instructions

Landis & Staefa REV11…

REV11… - the temperature controller that allows you to set the ideal room temperature at the

time you want. There are two switching patterns available that can be set to suit your specific

needs. You can either rely on the factory settings or make settings tailored to your personal

needs.

Setting slider

Changing the setting values

Display

Settin

Time of day

Room temperature

(measured)

Time of day

Remote operation active

(if connected)

Standby

Normal temperature

Heating on

Economy temperature

Replace batteries

°C

1.5V 'AA'

Operation

Continuous

normal temperature

Continuous

economy temperature

Standby

with frost protection

Operating mode

selector

Change

between normal and

economy mode up to the

next switching point

Warmer/colder setting

valid up to the next

switching point

(increments of 0.2 ºC,

± 4 ºC max.)

24-hour mode A

with 2 heating periods

Auto

Run

A1 A2 A3 A4

B1 B 2

Operating

position

Auto

Run

Economy

temperature

Normal

temperature

Switching times

B1...B2

Switching times

A1...A4

A2 A3 A4

2222Z11E

24-hour mode B

with 1 heating period

Commissioning with quick startup

The controller is supplied with factory-set switching patterns, switching times and

temperatures. To commission it, proceed as follows:

1.5V 'AA'

Remove the black transit tabs from the two batteries. Check to see if the battery

holder is in its correct position. The controller switches itself on.

Move the setting slider to the time position.

Press buttons to set the correct time of day.

Auto

Run

Move the setting slider back to position on the right, because only that position

allows you to close the cover.

Select the required operating mode with the operating mode selector (e.g.

Fold up the operating instructions again, place them back into the cover and close the cover

again.

Do you want to use automatic

operation?

If that is the case, set the operating

mode selector to one of the

following positions:

You use the 24-hour setting

with

two

heating periods.

You use the 24-hour setting

with

one

heating period.

Do you require continuous normal

temperature?

Move the operating mode selector

to «Normal temperature». This

ensures continuous heating to the

normal temperature. The display

shows

Do you require continuous economy

temperature?

Move the operating mode selector

to «Economy temperature». This

ensures continuous heating to the

economy temperature. The display

shows

Do you require continuous standby

with frost protection?

Move the operating mode selector

to «Standby». In that case, heating

is provided only when the room

temperature falls below the preset

frost protection limit (5 °C). The

display shows

Do you feel too warm or too cold?

°C

By pressing these buttons, you

increase or decrease the actual

room temperature in increments of

0.2 °C by a maximum of ± 4°C. The

display first shows the newly

selected temperature and then the

actual value again.

These

changes are valid only up to the

next switching point.

If, as a

result of the factory settings, you

always feel either too warm or too

cold, you should readjust the

temperature

or to suit your

needs

CE1B2222E / 27.01.1999 Subject to alteration Siemens Building Technologies / Landis & Staefa Division

Do you want to change the

temperature level or will you be

absent for a short period of time?

When pressing this button, you

change from the current

temperature level to the other. The

display shows either

, when the

change was made from the

economy temperature, or

, when

it was made from the normal

temperature. This means you can

select the economy temperature

during the time you are absent.

These changes are valid only up

to the next switching point.

Do you want to enter your own

temperatures and heating periods?

The controller has two different switching

patterns (A/B).

Proceed as follows:

Move the setting slider to the

switching position (e.g. A1) and

press

to enter the required

switching time.

All the other

switching positions (A2…A4 and

B1…B2) are set the same way.

Select «Normal temperature» and

press

to set the required value.

Select «Economy temperature»

and press

to set the required

value.

Auto

Run

Move the setting slider back to this

position and close the cover.

Table for entering selected values

Enter the values set by you in the following

table. The numbers already contained in the

table represent factory settings.

Temp.Switchin

times

A1 A2

A4 B1 B2

6.00 9.00 17.00 22.00 7.00 23.00 20° C 16° C

2222Z12E

Do you need to change the time of

day?

Move the setting slider to the time

of day position and press

set the correct time of day.

Auto

Run

Move the setting slider back to this

position and close the cover.

Do you wish to return to the factory

settings?

°C

By pressing these three buttons

simultaneously, a complete reset is

made, which means that the

switching times and temperatures

will be reset to their default values.

Caution: all individual settings

will be lost!

At the same time, a

display check is made, which looks

as follows:

2222Z13

Does the symbol appear in the

display?

If this symbol appears, you need to replace

the batteries within the next three months.

Do you want to change the batteries?

•

Get two new alcaline batteries type AA,

1.5 V.

•

Remove the battery holder, then the

batteries, insert the new batteries and

replace the battery holder.

Caution: The

setting data are maintained fora

maximum of one minute only!

•

Make certain the old batteries are

disposed of properly, in compliance with

environmental requirements.

Energy saving tips without sacrificing

comfort

•

Never allow room temperatures to exceed

21 °C.

•

Press

to change to economy

temperature, even if you are absent for

short periods of time only.

•

Air out the rooms for short periods of time

only, but properly, with the windows wide

open.

Auxiliary functions

Your room temperature controller provides a

number of auxiliary functions, but these

should only be set by your heating engineer.

Produkt Specifikationer

Mærke:	Siemens
Kategori:	Termostat
Model:	Landis & Staefa REV11

Har du brug for hjælp?

Hvis du har brug for hjælp til Siemens Landis & Staefa REV11 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Termostat Siemens Manualer

Siemens QAF64 Manual

28 December 2024

Siemens RDG100T Manual

15 Oktober 2024

Siemens DESIGO RXA Manual

5 Oktober 2024

Siemens REV33 Manual

3 Oktober 2024

Siemens RAA31 Manual

16 September 2024

Siemens REV100 Manual

2 September 2024

Siemens Landis & Staefa REV22RF Manual

1 September 2024

Siemens RDG160T Manual

1 September 2024

Siemens RDF600KN Manual

30 August 2024

Siemens REV23M Manual

30 August 2024

Termostat Manualer

Nyeste Termostat Manualer

14 September 2025

7 September 2025

7 September 2025

7 September 2025

7 September 2025

7 September 2025

7 September 2025

Bearware 303583 Manual

6 September 2025

MKC MKTI-1014 Manual

2 September 2025

MKC MKTI-1020 Manual

2 September 2025