Siemens RDG160T Manual

Siemens Termostat RDG160T

Læs gratis den danske manual til Siemens RDG160T (2 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om Siemens RDG160T, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Operating Instructions

RDG100T

RDG160T

RDG100T / RDG160T – the electronic room thermostat that allows you to set the ideal room

temperature you want. The thermostat provides Comfort, Economy and Protection mode and, in

addition, an Auto Timer mode with 8 programmable timers. The fan operates either in Automatic

mode or at the selected speed when using Manual mode. You can either rely on the factory settings

or make adjustments that suit your individual needs.

Main display Operating mode

Room temperature Heating mode

Room temperature in degrees

Celsius Electric heater on

Room temperature in degrees

Fahrenheit Cooling

Button lock active Comfort mode

Alert indicator Economy mode

Condensation in the room Auto timer

Temporary timer function

active

Protection mode:

Protection against

frost

Indicator for selecting

mode

Weekday 1 = Monday

7 = Sunday

Operating mode button

Setting time and weekday

Setting the auto timers

Fan mode

Program mode button Current time of day Automatic

T Fan mode button Escape (Cancel) Manual

Low Medium High

Rotary knob Confirmation (OK)

Changing the room temperature





The room temperature setpoint can be adjusted with the rotary knob when

Comfort mode is active or with



 Turn the rotary knob clockwise (+) to increase, or counterclockwise (-) to de

crease

the current room temperature setpoint for Comfort mode

The setting range is from 5...40 °C, unless limited by parameters P09 and P10 (for parameter settings,

see reverse side).

Adjusting the fan speed

Low Medium High



 Press the fan mode button until the desired fan mode is reached



 In Automatic mode

, the fan speed is automatically selected by the thermostat

depending on the setpoint and the actual room temperature.

When the room temperature reaches the setpoint, the fan stops (fac

tory setting) or

keeps running at low speed (P15).





In Manual mode, the fan operates independently and always runs at the same

speed: Low / medium / high

Note:

If desired, you can change the fan mode selector option via P03: Manually only, or manually

including Protection mode. Use P15 to set the fan speed in dead zone.

Changing from heating to cooling mode





Depending on the type of plant, the changeover from heating to cooling (or vice

versa) is made either automatically by a changeover sen

sor or a remote changeover

switch, or manually by pressing the operating mode button (see parameter P01)



 To select cooling or heating manually (P01=2), press the operating mode button

until the desired mode appears



 With automatic changeover or continuous heating / cooling, symbols /

indicate that the system currently operates in heating or cooling mode



 With manual changeover, symbol

appears, indicating that the system currently

operates in heating or cooling mode

Changing the operating mode

Press the operating mode button until symbol

appears, indicating that Protection /

Comfort / Auto Timer / Economy mode is selected.

1. Protection mode





In protection mode, the plant stops operating. If the room temperature falls below

8 °C, heating is switched on however to protect the room against frost

The setpoints for Protection mode can be changed by your HVAC installer if desired:

Changes made by installer: Frost protection: _________ C Heat protection: __________ C  

2. Comfort mode





In Comfort mode, the thermostat maintains the setpoint which can be readjusted

with the rotary knob

3. Auto Timer mode



 In Auto Timer mode

, the controller automatically switches over between Comfort

and Economy according to the 8 preprogrammed timers

4. Economy mode



 When selecting Economy mode, make sure that parameter P02 is set to 2



 In Economy mode, the room temperature is maintaine

d at a lower or higher

setpoint, thus saving energy and money! You can change the preselected

setpoint

by adjusting parameters P11 and P12 (for parameter settings, see reverse side)

Important: The setpoint for Economy can be set to OFF. This means that the thermostat is

deactivated! Risk of frost, i.e. no protective heating or cooling function is provided!

Setting the time of day and the weekday

1. Press the program mode button for programming.

2. Press button (OK) to enter the setting mode for the time of day.

The time digits start blinking. Turn the rotary knob clockwise or counterclockwise to set the time

of day.

If the current time of day is in 24-hour format and you wish to change it to the 12-hour format, turn

the knob clockwise passed 23:59 or counterclockwise passed 00:00. Vice versa back to the 24-hour

format.

4. Confirm the time of day by pressing button and the weekday indicator starts blinking.

5. Turn the rotary knob clockwise or counterclockwise to set the current weekday.

6. Confirm the current weekday by pressing button (OK).

7. Press button (Esc) to leave the program mode.

Note:

After a power failure, the time of day starts blinking to indicate power was lost. However, the auto timer continues to

run with the time before the power failure occurred. Select the setting mode to readjust the time if needed.

Setting the programmable timers

The RDG100T

provides 8 programmable timers A1…A8 each of which can be assigned to one or several

days. To set an auto timer, proceed as follows:

1. Press the program mode button twice to select auto timer setting .

2. Turn the rotary knob to the desired timer A1…A8 that you wish to set and press button (OK).

3. Turn the rotary knob to set the Comfort mode start time and confirm by pressing button (OK)

4. Turn the rotary knob to set the Comfort end time

or Economy start time and confirm by pressing

button (OK).

5. Weekday , and blink. Press button (OK) to select or

(Esc) to deselect each day and

advance to the next day.

After the 7th day is set, all selected weekdays blink. Confirm setting for actual timer by pressing

button

(OK) and advance to the next timer. To set the next timer, repeat steps 3 through 6, or

press (Esc) to leave the setting mode.

Notes:

- To save your settings, remember to press OK in step 6 above before pressing Esc to leave the setting mode.

- The timer function can be disabled by setting P02 = 3 or P02 = 4 (only RDG160T)

Viewing the settings

1. Press the program mode button twice to select auto timer setting .

2. Turn the rotary knob to review the 8 auto timers.

3. Press button (Esc) to return to normal operation.

Temporary timer for extended presence or absence

The Comfort and Economy modes can be temporarily extended from 0.5 to 9.5 hours using

the

temporary timer.

1. To set the temporary timer, press and hold the operating mode button for maximum 3 seconds.

While holding the button, turn the rotary knob clockwise or counterclockwise as required.

a) Turn the rotary knob clockwise to extend Comfort mode.

Display: 0....+9:30

b) Turn the rotary knob counterclockwise to extend Economy mode.

Display: 0....-9:30

After the temporary timer has elapsed, the thermostat will resume operation in Auto Timer mode.

Reloading the default timer settings

1. Press the program mode button twice to select auto timer setting .

2. Press button (OK) to enter the timer setting mode.

3. Press the program mode button for at least 3 seconds; then “rES” is displayed.

4. Press button (OK) to confirm reloading the default timer settings, or

(Esc) to leave without

change.

Default

settings

Weekdays Time of day when thermostat is in Comfort mode

Mon(1)- Fri(5) 06:30 – 08:30 (A1) 17:30 – 22:30 (A2)

Sat (6) 08:00-23:00 (A3)

Sun (7) 08:00-22:30(A4)

For the remaining time, the thermostat is in Economy mode.

Timers A5 - A8 are free with no default settings.

Button lock



 To lock or unlock the buttons manually, press and hold

the fan mode button for 3

seconds. The buttons are locked or unlocked in this manner if P14 is set to 2



 If P14 is set to 1, the thermostat automatically locks the button 10 seconds

after the

last adjustment

Control parameters

If you want to change control parameters, proceed as follows:

1. Press left and right buttons simultaneously for at least 4 seconds.

2. Release them and, within 2 seconds, press the right button again until “P01” is displayed.

3. Select the required parameter by turning the rotary knob.

4. Press button (OK). The current value of the selected parameter starts blinking and

can be changed

by turning the rotary knob.

5. Press button (OK) to confirm the adjusted value, or (Esc) to cancel the change.

If you wish to adjust additional parameters, repeat steps 3 through 5, or press

(Esc) to leave the

parameter setting mode.

No.

Parameter name Default value

Setting range Adj.

P01

Control sequence 2-pipe / 2-stage:

1 = cooling only

4-pipe:

4 = H and C

0 = heating only

1 = cooling only

2 = H/C changeover, manually

3 = H/C changeover, auto

4 = heating and cooling

P02 Mode selection via operating mode button 1

RDG100T: 1, 2

RDG160T: 1…4

1 = Auto / Comfort /

Protection mode

2 = Auto / Comfort / Economy /

Protection mode

3 = Comfort / Protection mode

4 = Comfort / Economy /

Protection mode

P03 Mode selection via fan mode button 0 0 = Auto / Manually

1 = Manually

2 = Auto / Manually /

Protection mode

P04 Selection of °C or °F 0 0 = °C

1 = °F

P05 Sensor calibration 0.0 K – 3 ... 3 K

P06 Standard temperature display 0 0 = Room temperature

1 = Setpoint

P08 Comfort basic setpoint 21 °C 5 ... 40 °C

P09 Minimum setpoint limitation in Comfort mode 5 °C 5 ... 40 °C

P10 Maximum setpoint limitation in Comfort mode 35 °C 5 ... 40 °C

P11 Setpoint for heating in Economy mode

(WheatEco)

15 °C OFF, 5 °C…WcoolEco

P12 Setpoint for cooling in Economy mode

(WcoolEco)

30 °C OFF, WheatEco…40 °C

P13 Electric heater in cooling mode ON OFF = Disabled

ON = Enabled

P14 Button lock 0 0 = Disabled

1 = Automatically

2 = Manually

P15 Fan speed in dead zone

(Comfort mode)

0 0 = Disabled

1 = Stage 1 (H or C)

2 = Stage 1 (Cooling only)

The control parameters displayed depend on the DIP switch settings made

Siemens Switzerland Ltd

Subject to change

B3181.5en

18.09.2013

Produkt Specifikationer

Mærke:	Siemens
Kategori:	Termostat
Model:	RDG160T

Har du brug for hjælp?

Hvis du har brug for hjælp til Siemens RDG160T stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Termostat Siemens Manualer

Siemens QAF64 Manual

28 December 2024

Siemens RDG100T Manual

15 Oktober 2024

Siemens DESIGO RXA Manual

5 Oktober 2024

Siemens REV33 Manual

3 Oktober 2024

Siemens RAA31 Manual

16 September 2024

Siemens REV100 Manual

2 September 2024

Siemens Landis & Staefa REV22RF Manual

1 September 2024

Siemens RDG160T Manual

1 September 2024

Siemens RDF600KN Manual

30 August 2024

Siemens REV23M Manual

30 August 2024

Termostat Manualer

Nyeste Termostat Manualer

Fantini Cosmi C900R Manual

13 August 2025

GE RAK190V Manual

12 August 2025

Honeywell CT50K1028/E Manual

12 August 2025

Honeywell RET97B5D1002/U Manual

12 August 2025

Honeywell RCHT9510WFW2001/W Manual

12 August 2025

Honeywell CT87K1004/E1 Manual

12 August 2025

Honeywell YCT87N1006 Manual

12 August 2025

Honeywell RTH7500D1049/A Manual

12 August 2025

Honeywell YCT50K1006 Manual

12 August 2025

Honeywell RTH2510B1000/U Manual

12 August 2025