Skan Holz Basel 2 Manual

Skan Holz Ikke kategoriseret Basel 2

Læs gratis den danske manual til Skan Holz Basel 2 (10 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Skan Holz Basel 2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/10

Basel 2 420 x 380cm

Important information for your wood panel cabin

Please check the construction set for completeness using the position list in good time before starting con-

struction or commissioning your construction team. If individual parts are defective or missing, we will deliver

these as quickly as possible. However, we cannot refund the costs for any resulting construction delays to a

construction company.

Please understand that we cannot assume any guarantee fort he following defects:

- incorrect storage before assembly

- incorrect anchoring with the ground or inadequate foundation (foundation according to statics)

- damage due to erection errors, e. g. the house is not level or not right-angled

- damage through a higher level of snow burden than statically envisaged. Recommendation: lad relief of

the roof by removing the snow layer

- storm damage (insurance cases) or violent destruction

- damage through any alteration to the design by the client

- natural formation of cracks, branch holes, twisting, decolouration or similar modification (natural process;

has no influence on the statics)

Storage tips before assembly:

- store pallet on a level and dry surface.

- protect against sunshine and dampness; wood can warp drastically in a loose condition!

Maintenance tips:

Please observe the attached information sheet “Care instructions/Colour treatment”.

610891 (unbehandelt)

610891-13 (schiefergrau)

General tips and refers to:

As the house is exposed constantly to the weather, it is necessary to lay a further welding line. You have to make

it for your own.

A possibly desired installation of a rain gutter must be done by the building contractor; for this the roofing boards

must be cut to the right length.

Foundation according (to the structural calculations, not included in the scope of delivery): concrete C25/30,

strip foundation: Bottom panel: w/h = 30/90cm, each 2 Ø 12 top and bottom, bow Ø 6, e < 20cm.

t=14cm,Q188A, top and bottom throughout. Anchoring of the floor beams on the strip foundation using bolts M12,

e < 60cm (by customer).

During the assembly of the planks that the planks are fixed with approx. it is essential to make sure 1mm

distance and the top planks have the same height all around.

Due to storage, the measurements of the planks may change over time and change the heigth of the wallplanks.

Please remember this during the installation of the planks, .otherwise it may result in different wall heights

If the door , this can be adjusted by .cannot be closed properly turning the hinges

The roofing boards are laid out up to the inner edge of the outer facing. The final roofing board must be adjusted

in width. The roofing boards must be cut out as necessary in the area near the fastening wood H58/58-00 (34cm).

It is planned to have the roofing paper go up the sides over the existing gap as high as the facing, and to attach it

there on the facing. The building contractor can also lay strips over the gap, or the roofing paper can be laid right

up to the upper edge of the facing; this will then be covered by the aluminium strip A100-220.

420 x 380cm

3 x H28/140-00

18cm

2 x H58/58-03

419cm

33 x H19/121-01

410,5cm

42 x H19/119-01

163,5cm

4 x 45-29-001

453cm

29 x H16/58-00

34cm

2 x H16/101-00

205,5cm

2 x H16/101-00

228cm

2 x H16/101-00

245cm

4 x H16/58-00

214,2cm

4 x H16/58-00

225,8cm

9 x A100-220

220cm

6 x H19/119-00

436,2cm

6 x H19/119-00

460cm

2 x H33/30-00

34cm

2 x H58/58-00

242cm

5 x H28/140-00

36,5cm

10 x H12/40-00

350cm

42 x H19/119-01

191cm

1 x 45p-D

6 x H19/58-02

300cm

42 x H19/119-01

74,5cm

9 x H58/58-03

367,4cm

2 x H16/101-00

219cm

1 x H19/120-00

26cm

1 x H16/58-00

16cm

1 x H19/120-00

29cm

1 x H16/58-00

12cm

2 x H19/120-00

23cm

2 x H16/58-00

32cm

1 x H16/101-00

228cm

9 x H12/25-00

130cm

610891

Produkt Specifikationer

Mærke:	Skan Holz
Kategori:	Ikke kategoriseret
Model:	Basel 2

Har du brug for hjælp?

Hvis du har brug for hjælp til Skan Holz Basel 2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Skan Holz Manualer

Skan Holz Varberg 1 Manual

31 Maj 2025

Skan Holz Alicante 2 Manual

31 Maj 2025

Skan Holz Knut Manual

30 Maj 2025

Skan Holz Almelo Manual

30 Maj 2025

Skan Holz Varberg 2 Manual

30 Maj 2025

Skan Holz Grunewald Manual

30 Maj 2025

Skan Holz Breda 2 Manual

30 Maj 2025

Skan Holz Basel 1 Manual

30 Maj 2025

Skan Holz Esbjerg 3 Manual

30 Maj 2025

Skan Holz Narvik Manual

30 Maj 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

AXIL AN0268G5 Manual

16 Juli 2025

CYP EL-21PIP Manual

16 Juli 2025

Rockville MAC360W Manual

16 Juli 2025

Zeiss Conquest V4 4-16x44 Manual

16 Juli 2025

DS18 MRX300D Manual

16 Juli 2025

Daewoo DJNS08S Manual

16 Juli 2025

DS18 SLG-FKP6LD Manual

16 Juli 2025

Märklin 72211 Manual

16 Juli 2025

Rockville RockZR Manual

16 Juli 2025

ENDORFY Broadcast Low Profile Boom Arm Manual

16 Juli 2025