Skan Holz Breda 2 Manual

Skan Holz Ikke kategoriseret Breda 2

Læs gratis den danske manual til Skan Holz Breda 2 (20 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om Skan Holz Breda 2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/20

Important information

We are pleased that you have chosen a product of SKAN HOLZ.

Please check the construction set for completeness using the position list in good time before starting con-

struction or commissioning your construction team. If individual parts are defective or missing, we will deliver

these as quickly as possible. However, we cannot refund the costs for any resulting construction delays to a

construction company.

Please understand that we cannot assume any guarantee for the following defects:

- incorrect storage before assembly

- incorrect anchoring with the ground or inadequate foundation (foundation according to statics)

- damage due to erection errors, e. g. the house is not level or not right-angled

- damage through a higher level of snow burden than statically envisaged. Recommendation: lad relief of

the roof by removing the snow layer

- storm damage (insurance cases) or violent destruction

- damage through any alteration to the design by the client

- natural formation of cracks, branch holes, twisting, decolouration or similar modification (natural

process; has no influence on the statics)

Storage information until construction:

- store pallet on a level and dry surface.

- ; wood can warp drastically in a looseProtect from exposure to sunlight and the influences of weather

condition!

Maintenance tips:

Please observe the attached information sheet “Care instructions/Colour treatment”.

General tips and refers to:

The packaging foil to keep moisture out of the house. It is laid according to the ground area of thecan be used

house under the main bearing.

As the house is exposed constantly to the weather, it is necessary to lay a further welding line. You have to make

it for your own.

A possibly desired installation of a rain gutter must be done by the building contractor; for this the roofing boards

must be cut to the right length.

Foundation according to the structural calculations (not included in the scope of delivery): concrete C25/30,

each 2 Ø 12 top and bottom, brace mat R188A (alternatively brace Ø 6/20cm). Anchoring of the floor beams

(in the building) on the strip foundation using bolts M12, e < 60cm. The base bearings in the storeroom of the

house must be entirely flush.

During the assembly of the planks that the planks are fixed with approx. it is essential to make sure 1mm

distance and the top planks have the same height all around.

Due to storage, the measurements of the planks may change over time and change the heigth of the wallplanks.

Please remember this during the installation of the planks, .otherwise it may result in different wall heights

If the door , this can be adjusted by .cannot be closed properly turning the hinges

The roofing boards are laid out up to the inner edge of the outer facing. The final roofing board must be adjusted

in width. The roofing boards must be cut out as necessary in the area near the fastening wood H16/58-00 (34cm).

It is planned to have the roofing paper go up the sides over the existing gap as high as the facing, and to attach it

there on the facing. The building contractor can also lay strips over the gap, or the roofing paper can be laid right

up to the upper edge of the facing; this will then be covered by the aluminium strip A100-220.

Breda 2 380 x 380cm

603527 (unbehandelt)

603527-13 (schiefergrau)

603527-15 (schwedenrot)

2 x H28/140-00

18cm

4 x 28-29-002

413cm

4 x H16/58-00

219cm

3 x H16/58-00

228cm

2 x H16/58-00

428,4cm

2 x H16/58-00

411,6cm

8 x

6 x H19/119-01

420cm

2 x H30/33-00

34cm

4 x H28/140-00

36,5cm

8 x H12/40-00

350cm

1 x H20/46-00

123,4cm

6 x H5

379

33 x H19/121-01

373,5cm

8 x H20/20-04

200cm

38 x H19/119-01

163,5cm

380 x 380cm

603

38 x H19/119-01

189,5cm

38 x H19/119-01

74cm

2 x H16/58-00

233cm

Produkt Specifikationer

Mærke:	Skan Holz
Kategori:	Ikke kategoriseret
Model:	Breda 2

Har du brug for hjælp?

Hvis du har brug for hjælp til Skan Holz Breda 2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Skan Holz Manualer

Skan Holz Varberg 1 Manual

31 Maj 2025

Skan Holz Alicante 2 Manual

31 Maj 2025

Skan Holz Knut Manual

30 Maj 2025

Skan Holz Almelo Manual

30 Maj 2025

Skan Holz Varberg 2 Manual

30 Maj 2025

Skan Holz Grunewald Manual

30 Maj 2025

Skan Holz Breda 2 Manual

30 Maj 2025

Skan Holz Basel 1 Manual

30 Maj 2025

Skan Holz Esbjerg 3 Manual

30 Maj 2025

Skan Holz Narvik Manual

30 Maj 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Salton MP1206 Manual

31 August 2025

TensCare Sports TENS 2 Manual

31 August 2025

Pardini K58 Manual

31 August 2025

Salton SCG-4 Manual

31 August 2025

Salton JK-1103 Manual

31 August 2025

Salton WC-2040 Manual

31 August 2025

Salton WC-2070 Manual

31 August 2025

Salton SP1963 Manual

31 August 2025

Gram EFI 8060-91 B Manual

31 August 2025

Analog Way Orchestra² Manual

31 August 2025