Sloan SS-3117 Manual

Sloan Køkkenvask SS-3117

Læs gratis den danske manual til Sloan SS-3117 (2 sider) i kategorien Køkkenvask. Denne vejledning er vurderet som hjælpsom af 38 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 19.5 anmeldelser. Har du et spørgsmål om Sloan SS-3117, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

[194]

[286]

11.25

[863]

FINISHED

FLOOR

[103]

MOUNTING

BRACKET

HOLES (4)

• Determine the desired height to the top of lavatory

sink rim. Mark level line on wall. This line is

centerline of holes for wall hanger bracket

mounting holes.

• Mark and drill holes in wall for mounting lavatory

BEFORE YOU START…

• Check all local plumbing and building codes.

• Check for any damage to the new lavatory sink

before installation.

WHAT YOU WILL NEED…

• Putty knife • 10” adjustable wrench

• Safety glasses • Phillips screwdriver

• Measuring tape • Flathead screwdriver

• Basin wrench • Drill

• Tube cutter • Plumbers putty

• Hacksaw • Silicone sealant

• Channel lock pliers

THE RIGHT CHOICE

We thank you for your purchase. Our products are

100% tested but should you have any questions,

please contact us by phone or at our web site.

Enameled Cast Iron Wall-Hung Lavatory Installation

Model

SS-3017 / SS-3117

The information contained in this document is subject to change

without notice.

SLOAN VALVE COMPANY

10500 Seymour Avenue

Franklin Park, IL 60131

Phone: 1-800-9-VALVE-9 (982-5839)

or 1-847-671-4300

Fax: 1-800-447-8329 or 1-847-671-4380

www.sloanvalve.com

Code No. 0816874 Rev. 1 (08/19)

RETROFIT INSTALLATIONS

1. REMOVE EXISTING LAVATORY

• Turn off the water supply.

• Disconnect the supply lines and waste pipes.

• Remove the existing lavatory.

• Scrape any old putty or sealant from wall surface.

• Remove old wall bracket and discard.

• Adequate structural support in or behind the wall

is required to withstand the weight of the lavatory

when lled with water.

2. CLEAN DRAIN

• Clean out waste pipe using hand or power cleaner

to be sure pipe is clear.

• Proceed to NEW INSTALLATIONS.

Wall Carrier rough-in information to be provided by wall carrier

manufacturer. Carrier and hardware not included with xture

SS-3017

NEW INSTALLATIONS

1. PRIOR TO NEW INSTALLATION

• Determine appropriate wall location for the lavatory.

Consider that hot and cold water supply lines with

supply stops or a tempered water supply line with

supply stop and a drain line will be required. A 120V

electrical source (receptacle) may also be required.

Compare the physical dimensions of the lavatory to

the space available for the installation.

2. UNPACK AND INSPECT LAVATORY

• Carefully remove sink from its protective carton so

as not to damage nish. Check for any damage to

lavatory before proceeding with the installation.

• Examine the carton for additional parts before

discarding packaging.

3. INSTALL DRAIN AND FAUCET

• Install the faucet and drain assembly (not included).

Follow faucet manufacturers instructions. Use

plumbers putty to ensure a water seal.

4. INSTALL NEW WALL HANGER BRACKET

Reinforced wall framing

Holes for Hanger Bracket

Note: Adequate reinforced wall framing is

required behind the wall for proper hanger

bracket support. Use of wall anchors or toggle

bolts is not recommended. For concrete walls

a properly sized wall anchor can be used.

• Mount and level wall hanger bracket using six (6)

screws and washers (not supplied)

5. INSTALL LAVATORY ON WALL BRACKET

Note: Check if lavatory is level. If not level,

remove lavatory and adjust wall bracket as

needed.

Install two (2) 5/16” anchor bolts (not supplied),

through the (2) 3/8” anchor holes, in the sink and into

the wall.

COMPLETING THE INSTALLATION

• Connect all supply lines and waste pipes.

• Turn on water. Check to see that the faucet

and drain are operating properly and there

are no leaks.

• Caulk around lavatory perimeter where lavatory

meets the wall.

• Record lavatory model number for reference.

CARE AND CLEANING OF SLOAN FIXTURES

LIMITED WARRANTY

Sloan Valve Company warrants its products to be made

of rst class materials, free from defects of material

or workmanship under normal use and to perform the

service for which they are intended in a thoroughly

reliable and efcient manner when properly installed

and serviced, for a period of three years from date of

purchase. During this period, Sloan Valve Company

will, at its option, repair or replace any part or parts

which prove to be thus defective if returned to Sloan

Valve Company, at customer’s cost, and this shall

be the sole remedy available under this warranty. No

claims will be allowed for labor, transportation or other

incidental costs. This warranty extends only to persons

or organizations who purchase Sloan Valve Company’s

products directly from Sloan Valve Company for

purpose of resale.

THERE ARE NO WARRANTIES WHICH EXTEND

BEYOND THE DESCRIPTION ON THE FACE

HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY

RESPONSIBLE FOR ANY CONSEQUENTIAL

DAMAGES OF ANY MEASURE WHATSOEVER.

NOTE: IN NO EVENT SHALL THE SLOAN VALVE

COMPANY BE LIABLE FOR INCIDENTAL DAMAGES,

RESULTING FROM IMPROPER INSTALLATION, OR

FOR DAMAGES CAUSED BY NEGLECT, ABUSE OR

ALTERATION.

All dimensions shown in these drawings are nominal and not to

scale. Dimensions can vary within the tolerances established in

the governing ASME A112.19.1-2008. It is important to consider

this when planning rough-in and plumbing layouts.

Clean lavatory with a cleaner safe for enameled cast

iron. Spray and wipe clean using soft cloth. Soft

abrasive cleaners may be used to remove stains.

Produkt Specifikationer

Mærke:	Sloan
Kategori:	Køkkenvask
Model:	SS-3117

Har du brug for hjælp?

Hvis du har brug for hjælp til Sloan SS-3117 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Køkkenvask Sloan Manualer

20 Juni 2025

16 Juni 2025

16 Juni 2025

15 Juni 2025

15 Juni 2025

Køkkenvask Manualer

Nyeste Køkkenvask Manualer

Sterling B153 Manual

15 December 2025

Sterling B155 Manual

10 December 2025

Berg ALLON BRA Manual

6 December 2025

IMC/Teddy CMSC-R Manual

30 November 2025

Klarstein TitanSteel Manual

29 November 2025

Signature Hardware Linwald 484626 Manual

13 November 2025

Signature Hardware Calverton SHCAUCA16R Manual

11 November 2025

Signature Hardware Totten SHGR1B3320ABL Manual

11 November 2025

Royal Catering RCGS-2B180D7 Manual

3 November 2025

Royal Catering RCGS-2B1800D6 Manual

3 November 2025