Sonneman Nebula 2067.25 Manual

Sonneman lampe Nebula 2067.25

Læs gratis den danske manual til Sonneman Nebula 2067.25 (9 sider) i kategorien lampe. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Sonneman Nebula 2067.25, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/9

June 16, 2020

1 of 8

LED Product Information and Warnings

Important

• Always disconnect the power before installing or replacing parts and before cleaning or other maintenance.

• Consult a qualied, licensed electrician to ensure correct branch circuit conductor.

• Please read all included assembly instructions and warnings carefully before installation. Contact

Customer Service if you have any questions or concerns. Before installation, please conrm that the xture

is compatible with your supply voltage and dimming system, if present.

• LEDs are highly sensitive electronic devices, and must be treated with care. Do not open any factory

sealed compartments, and avoid touching the LEDs with your hands or any object.

• Although all our xtures are equipped with protective devices, LED xtures are vulnerable to power surges

and supply variations. Do not install LED xtures on the same circuit as any motors, appliances, or HVAC

systems.

• Do not remove or bypass any LED Driver or Transformer that is provided with the xture, and do not

replace or substitute with another power supply.

• Remote LED Driver or Transformer installation must be done by a licensed electrician and in accordance

with local codes. Remote installations should be in an accessible location, as close to the xture as possible.

• Fixtures must be wired in parallel on independent leads; do not "daisy chain" multiple xtures together or

wire them in series.

• All factory-made splices and connections must remain intact. LED circuits are carefully designed and built,

and improper connections may damage the xture.

• The ends of coaxial pendant cords have been precisely stripped and split at the factory and must not be

eld cut. Excess cord or cable should be neatly coiled and reserved in the xture canopy.

• Any mounting hardware is provided for your convenience and should be used with discretion. Always use

the appropriate hardware for the mounting surface.

June 16, 2020

2 of 8

Assembly Instructions

INSTRUCTIONS D’INSTALLATION

Nebula Series - Zig Zag LED Pendant

Important

• Always disconnect the power before installing or replacing parts and before cleaning or other maintenance.

• Consult a qualied, licensed electrician to ensure correct branch circuit conductor.

Consulter un électricien qualié pour vous assurer que les conducteurs de la dérivation sont adéquats.

1. Shut o power to the outlet box (A).

2. Attach the mounting plate (B) to ceiling using slots and wood screws (C). CAUTION: Fixture must be supported

independent of outlet box. Customer is responsible for ensuring appropriate ceiling construction to support the

weight of the xture.

3. Assemble xture frame (T) according to the Frame Assembly instructions on Page 3.

4. Determine the height at which the xture (T) is to be hung. Install the mounting brackets (P) to the ceiling with

anchors (Q) and screws (R), then screw the posts (S) onto the mounting brackets. Insert cables (B) into posts and adjust to

level the xture: to shorten, push the cable up; to lengthen, push in the plunger while pulling down on the cable, release

the plunger to lock. Support frame using sawhorses (or equivalent) while mounting and leveling.Suggestion:

5. Insert two power cords (D) through corresponding holes in canopy (E).

6. Use the screwdriver (G) to loosen the slotted set screws (H) in the two

cord posts (J). Insert the cords and adjust to the desired length.

Note: Cords must not support xture weight.

Tighten the set screws to set. Reserve extra cord in canopy (E).

7. Make appropriate electrical connections using wire nuts (Appendix A):

a. Connect the two LED driver (U) live wires (black) to the

outlet box live wire.

b. Connect the two LED driver (U) neutral wires (white) to

the outlet box neutral wire.

c. Connect the ground wire (green or uncoated) to the

outlet box ground wire. If no ground is present in outlet

box, connect ground wire to

the mounting plate (B) using

the green screw (included).

d. For each cord, connect the

cord inner conductor to one

of the driver positive (+)

output wire and connect the

cord outer conductor to the

driver negative (-) output wire.

Repeat for the second cord

and second driver.

8. Attach canopy (E) to the

mounting plate (B),

secure with canopy nut (V).

9. Install Cluster Arms and attach

globes (K1, K2, K3) as shown

on pages 4-7.

10. Restore power to

the outlet box (A).

Note

• This xture is dimmable with Electronic Low Voltage (Trailing-Edge), Incandescent (Leading-Edge), and 0-10V type

dimmers only.

Care Instructions

• Dusting: Use a clean, dry cloth.

• Cleaning: To protect the nish, avoid any harsh abrasives or chemicals.

2067

Produkt Specifikationer

Mærke:	Sonneman
Kategori:	lampe
Model:	Nebula 2067.25

Har du brug for hjælp?

Hvis du har brug for hjælp til Sonneman Nebula 2067.25 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

lampe Sonneman Manualer

Sonneman Ray 2036 Manual

2 April 2025

Sonneman Nebula 2067.25 Manual

12 September 2024

Sonneman Stix 2789.16 Manual

12 September 2024

lampe Manualer

Nyeste lampe Manualer

NUVO Arabel 60/6967 Manual

4 April 2025

NUVO Gotham 60/191 Manual

4 April 2025

NUVO Cordello 60/7884 Manual

4 April 2025

NUVO Clarksville 60/8061 Manual

4 April 2025

NUVO Gotham 60/190 Manual

4 April 2025

Integral LED ILSTRGBWB028E Manual

4 April 2025

Trust Shyne 25483 Manual

3 April 2025

Trust Vybz GXT 904 Manual

3 April 2025

Schonbek Priscilla BC7106N-48PBZ Manual

2 April 2025

Bresser BR-7RGB Mini Tube Manual

2 April 2025