Soundskins SSK-RAP4DRV2 Manual

Soundskins Ikke kategoriseret SSK-RAP4DRV2

Læs gratis den danske manual til Soundskins SSK-RAP4DRV2 (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 27 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 14 anmeldelser. Har du et spørgsmål om Soundskins SSK-RAP4DRV2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

Truck Door Kit Instructions

1. Start by locating the fastening hardware on the door

panel, take the appropriate screw driver and remove.

2. Once all the screws are removed you can take off the

door panel using a panel tool. Be sure to not break any

of the clips or mounting hardware. Pull panel away slowly

and unplug any electrical connections.

3. Now you are ready to prep the metal surface

using a microfiber cloth, Acetone (use a breathing mask),

and wipe away any moisture, oil, debris or etc. Then let air

dry for an appropriate time. The point is to get the surface

clean to ensure material glue contact.

• Screw driver

• Panel tool

• Microber cloth

• Acetone or cleaning solution

• Razor blade

• Roller

Tools needed for installation:

Soundskins USA

13452 Alondra Blvd, Cerritos, Ca 90703

Phone: 877.211.5597

Email: team@soundskinsglobal.com

www.SoundSkinsGlobal.com

4. When the surface is dry and clean, locate the

piece of the kit with the label on the back that coincides

with the door you’re working on. Make sure it lines up

correctly before you pull the backing off. After you confirm

the right piece, pull off the backing paper and apply the

material at the top and working your way down with a roller.

Make sure the material is pushed down completey and that

no air is trapped. Use a razor blade point or household

needle to release air. Repeat these steps for all door panels.

6. Now you are ready to place the door panel back on your

door. All necessary openings will be available after you

have applied the SoundSkins material. Secure door panel

with all screws and you are now ready to hit the road!

5. Press down firmly onto the area where your car speaker

hole is, and feel for the speaker wire. Use a razor blade to

cut around the speaker hole, being careful to not cut the

wire harness. Take the piece you just cut out and stick it

behind the speaker hole on the outer door skin to act as a

backwave. Score the area where the wire harness is with

your blade and tuck the harness between the two flaps.

Plug in your speaker.

Produkt Specifikationer

Mærke:	Soundskins
Kategori:	Ikke kategoriseret
Model:	SSK-RAP4DRV2

Har du brug for hjælp?

Hvis du har brug for hjælp til Soundskins SSK-RAP4DRV2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Soundskins Manualer

Soundskins SSK-STRIP Manual

12 Marts 2025

Soundskins SSK-WAVYPLUS Manual

12 Marts 2025

Soundskins SSK-GLDTR4DR Manual

1 September 2024

Soundskins SSK-RDGLD14 Manual

1 September 2024

Soundskins Rings v3 SSK-RINGS Manual

1 September 2024

Soundskins SSK-STGLD14 Manual

1 September 2024

Soundskins SSK-SEK Manual

1 September 2024

Soundskins SSK-F2504DR Manual

1 September 2024

Soundskins SSK-RAP4DR Manual

1 September 2024

Soundskins SSK-BRONCO Manual

1 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vulcan 1024W Manual

15 Juni 2025

Backyard Pro 554PL2030 Manual

15 Juni 2025

Haier 1U18TE2HDA Manual

15 Juni 2025

AEG EWKEXT1 Manual

15 Juni 2025

Planet XGPN-400AXV Manual

15 Juni 2025

Cadac 3 Cook Turbo Manual

15 Juni 2025

Bobrick B-3944 Manual

15 Juni 2025

Sony SZC-4008 Manual

15 Juni 2025

Watts ETX-15 Manual

15 Juni 2025

Sigma REMOTE ONE Manual

15 Juni 2025