SpeakerCraft DT6 Zero Manual

SpeakerCraft Højttaler DT6 Zero

Læs gratis den danske manual til SpeakerCraft DT6 Zero (4 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 36 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 18.5 anmeldelser. Har du et spørgsmål om SpeakerCraft DT6 Zero, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
OWNER’S MANUAL
SPEAKER PLACEMENT
Before installing your speaker, you should consider the placement carefully, taking into account the location of
electrical, plumbing and other fixtures. Contact your dealer for assistance if you are not sure of the best loca-
tion in your particular room environment.
Ceiling Placement: When placing your speaker into the ceiling, it should ideally be located above the pri-
mary listening area. The DT is intended to be used as a single stereo speaker in small listening environments,
walk-in closets, laundry rooms, bath rooms etc. In a large area, it may be necessary to place additional speak-
ers throughout the room to get the optimal effect.
MOUNTING SURFACE PREPARATION
New Construction - Unfinished Ceilings
A New Construction Bracket, SpeakerCraft part number BKT90611 (available from your dealer), may be
installed prior to drywall application across joists (up to 24" on-center) where a speaker will be located.
Insulation material should be in place prior to installing drywall. After the hole is cut and the drywall is
installed, the speaker can then be easily installed following the instructions for mounting under “Finished
Ceilings” below.
Finished Ceilings
Prior to the actual installation of the speaker, it will be necessary to run cables to the speaker location. See
your dealer for more information on cable installation. After the cable has been properly installed, you are
ready to mount the speaker. Following the simple steps listed below will result in a professional looking instal-
lation:
1. Determine the best area to mount your speaker. This area of the ceiling should be free of obstructions such
as electrical conduit, HVAC ducts, or water lines. This can best be determined by noting the placement of
fixtures and gaining access to an attic or crawl space for further analysis of the location of such obstacles.
2. Find the joists nearest the desired speaker mounting location. We highly recommend using a good stud-
finder tool for this procedure. If you are lining up the speaker to some other object or molding in the
room, make sure you consider the size of the baffle flange which extends beyond the mounting hole.
3. Mark the hole. A punch out template for setting the hole is provided in the box. Position the template in
the desired position and pencil an outline on the ceiling.
4. CAUTION:Cutting the hole. This is the most important part
of the entire installation. If you are not certain whether any
obstructions exist behind the desired mounting area, you
should start by cutting a small hole in the center of your
penciled mounting hole with a drywall saw, cutting at a 45º
angle towards the inside of the hole. (See Diagram 1)
Cutting the small hole at this angle will make drywall repair
much easier, using the piece cut out. Once you have deter-
mined that there aren’t any obstructions in your desired
mounting location, start cutting the finished hole at a 90º
angle to the ceiling’s surface.
DT6 Zero
Single Stereo Speakers
Diagram 1
Page 2 Eazy6 Owner’s Manual Page 2 DT6 Zero Owner’s Manual
5. Add insulation. If the area in the ceiling is not already insulated, add an
adequate amount insulation material to loosely cover the back of the
speaker. If the insulation material used is faced with foil or paper, position
the foil or paper away from the speaker.
SPEAKER INSTALLATION
The unique integral four foot mounting system incorporated into your AIM DT
speaker allows for a quick installation by following these easy steps.
1. Remove the grille. It may be necessary to push one or two of the mount-
ing screws, and its attached foot, towards the baffle and against the inside
surface of the grille to force the grille out of its retaining groove.
2. Attach the speaker cable (observing the proper polarity with your amplifier,
+ to + and - to -). Either channel may be attached to either terminal set,
however, be sure that polarity (+ and -) is correct on each channel or the
performance of the speaker will be seriously affected, as one channel will
cancel out the other. (See Diagram 2)
3. Make sure the mounting feet are turned inward to clear the opening,
and insert the speaker into the ceiling. Position the speaker into the hole.
Note: The flange of the speaker is designed to flex and conform to any
small imperfections in the ceiling’s surface. Tighten the four screws on the
front of the baffle only enough to make the flange become snug against
the ceiling. As you tighten the screws, the feet will automatically flip into
an outward position thereby clamping the drywall between the feet and
the flange. (See Diagram 3)
CAUTION: Over tightening may warp the baffle, crack the ceiling, cause
the flange to distort, and make the grille difficult to install.
4. Push the grille firmly into the slot in the speaker baffle.
SPEAKER ADJUSTMENT
Adjusting the Pivoting Tweeters
Once the woofer is positioned, further refinement can be made by pointing
the tweeter towards the listener. Gently pivot the tweeter to point it in the
desired direction (See Diagram 4).
PAINTING THE SPEAKER
If you plan to paint your speaker, we recommend that it be done prior to
installation. If you plan to paint your speaker sometime in the future, it is
best to remove it by simply reversing the steps for “Speaker Installation” listed
above. If it is necessary to paint the speaker while it is still in the ceiling, the
paint mask provided in the carton must be installed in place of the grille while
the flange is being painted with the ceiling. The grille can also be painted,
however, great care should be taken not to clog the holes as this will greatly
reduce the sound quality of the speaker. SpeakerCraft recommends only light
spray painting using 5 parts thinning agent to 1 part paint. Do not paint the
grille while it is attached to the speaker.
Diagram 3
Diagram 2
Diagram 4
Pivot the Tweeter by gently
pushing on the sides

Produkt Specifikationer

Mærke: SpeakerCraft
Kategori: Højttaler
Model: DT6 Zero

Har du brug for hjælp?

Hvis du har brug for hjælp til SpeakerCraft DT6 Zero stil et spørgsmål nedenfor, og andre brugere vil svare dig


Højttaler SpeakerCraft Manualer

SpeakerCraft

SpeakerCraft DT8 Zero Manual

30 August 2024
SpeakerCraft

SpeakerCraft DT6 Zero Manual

30 August 2024
SpeakerCraft

SpeakerCraft CRS6 Two Manual

16 August 2024
SpeakerCraft

SpeakerCraft CRS8 Two Manual

16 August 2024
SpeakerCraft

SpeakerCraft AIM7 Two Manual

16 August 2024

Højttaler Manualer

Nyeste Højttaler Manualer

The Box Pro

The Box Pro DSX 110 M Manual

1 August 2025
Muse

Muse M-968 BTY Manual

1 August 2025
Grundig

Grundig Portable 360 Manual

1 August 2025
Grundig

Grundig Band 360 Manual

1 August 2025
Grundig

Grundig GBT Connect 360 Manual

1 August 2025
Muse

Muse M-968 BTR Manual

31 Juli 2025
JLab

JLab Epic Party Manual

31 Juli 2025
JVC

JVC XS-E423 Manual

30 Juli 2025
SoundTube

SoundTube RF31-EZ-T Manual

30 Juli 2025
Valcom

Valcom VIP-480AL-W-SA Manual

30 Juli 2025