Spectron SP 112 Manual

Spectron Bilradio SP 112

Læs gratis den danske manual til Spectron SP 112 (2 sider) i kategorien Bilradio. Denne vejledning er vurderet som hjælpsom af 8 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 4.5 anmeldelser. Har du et spørgsmål om Spectron SP 112, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
SPECTRON BANDPASS SUBWOOFER
Congratulations on your purchase of this SPECTRON bandpass
subwoofer system.
Read and follow the operating and adjustment instructions for
this trunk box subwoofer model given below carefully, to
obtain best possible sound quality and performance from this
product.
KEY FEATURES
ILOADED WITH SPECTRON SP-S10/12 WOOFER
ILARGE CROSS SECTION SLOT PORT FOR HIGH SPL
ICHROMED WOOFER GRILLE WITH BICOLOR
LED ILLUMINATON
IMDF CABINET WITH INTERNAL BRACING
ISPACE SAVING SLOPED REAR WALL DESIGN
ICURVED ACRYLIC WINDOW FOR LOW FLEX
ISPRING-LOADED TERMINAL
For safety and legal reasons, it might be prohibited using the box illumination while operating a car. Restrictions may apply
in certain countries. For making sure to follow all national traffic and vehicle regulations and not to distract drivers attention,
we recommend connecting the box illumination to the interior light of the trunk.
TECHNICAL SPECIFICATIONS
Model: SP-110BP SP112BP
Enclosure type: 10” Bandpass Subwoofer 12” Bandpass Subwoofer
Frequency response: 30 Hz – 120 Hz 25 Hz – 120 Hz
Nominal impedance: 4 ohms 4 ohms
Sensitivity 1W/1m: 90 dB 92 dB
Maximum power handling: 400 W 500 W
Dimensions WxHxD: 425 x 310 x 225/390 mm 485 x 375 x 235/435 mm
PLACEMENT OF BOX
This SPECTRON bandpass model is designed and engineered to be placed in the trunk of the car, to achieve full bass
perfomance and low end extension.
POWER CONNECTION FOR LED ILLUMINATION
Connect the 3.5mm plug with the extension wire to the receptor inside the terminal. Connect the loose ends to an appropriate
switched 12V source like the trunk box illumination, if you intend to use the illumination feature of this product.
AUDIO CONNECTION AND SETTINGS
Before any adjustments are attempted, “treble“, “bass“ and “loudness“ controls of the head-unit must be set to their neutral/zero
position. Your bandpass subwoofer needs a low-pass filtered signal with at least 12dB/oct. slopes for best results.
§Activate the lowpass function of the amp channel(s) driving your bass box.
§Set the lowpass crossover frequency of the channel(s) driving the sub to approx. 80 Hz
§Connect the speaker wire of your sub amp to the speaker terminal on the backside of the sub.
§Increase the input gain of the subwoofer channel, until bass output is loud enough.
„In-phase“ connection of your subwoofer is critical – if your sub plays out of phase, the output at the crossover frequency region
will be depressed due to cancellation effects.
Thus one connection polarity of your sub will give you a „fatter“ and more dynamic bass reproduction in the 80Hz range.
That’s the one to go for.
manual SP-110BP_112BP:manual spectron 012W + WX 28.02.2008 15:06 Uhr Seite 1

Produkt Specifikationer

Mærke: Spectron
Kategori: Bilradio
Model: SP 112

Har du brug for hjælp?

Hvis du har brug for hjælp til Spectron SP 112 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Bilradio Spectron Manualer

Spectron

Spectron SP-S24 Manual

22 August 2024
Spectron

Spectron SP-S26 Manual

13 August 2024
Spectron

Spectron SP 112 Manual

7 August 2024

Bilradio Manualer

Nyeste Bilradio Manualer

Boss

Boss MCBK634B Manual

4 December 2025
Auna

Auna MVD-480 Manual

30 November 2025
Snooper

Snooper SMH-550DAB Manual

11 November 2025
Kenwood

Kenwood eXcelon DAX8000S Manual

8 November 2025
Kenwood

Kenwood eXcelon DAX800XR Manual

8 November 2025
Kenwood

Kenwood eXcelon DMX1058XR Manual

7 November 2025
RetroSound

RetroSound Liberty M2 Manual

30 Oktober 2025
RetroSound

RetroSound Liberty M1 Manual

30 Oktober 2025
Sony

Sony DSX-GS80 Manual

28 Oktober 2025
Audison

Audison VRX 2 150 Manual

19 Oktober 2025