SSV Works X3-DM3 Manual

SSV Works Ikke kategoriseret X3-DM3

Læs gratis den danske manual til SSV Works X3-DM3 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 47 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 24 anmeldelser. Har du et spørgsmål om SSV Works X3-DM3, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
X3-DM3
Can-Am Commander X3
Dash Kit for MRB3
SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030
www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751
!
Please read and understand these
instructions completely before
installation to avoid possible injury, or
damage to the accessory or vehicle.
WARRANTY INFORMATION:
All SSV Works enclosures are covered by a limited lifetime warranty against defects in
material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty
against defects in material or workmanship. All SSV Works Speakers are covered by a
limited 1 year warranty against defects in material or workmanship. Labor for replacement of
defective components is not covered. Contact SSV Works for further warranty information.
1. X3-DM3 Base Plate
2. X3-DM3 Top Panel
3. #7 x 1.25 Kit Screws x4
TOOLS NEEDED FOR INSTALLATION PARTS LIST
PARTS LIST IMAGES
4. M3 x 20mm Screws x2
5. M3 Washers x 2
6. M3 Hex Nuts x 2
2. X3-DM3 Top Panel
1. X3-DM3 Base Plate
- #2 Phillips Screw Driver
- 1/8” drill bit
- 1/2” drill bit
- Drill
INSTALLATION NOTES
For instrucitons regarding the MRB3 black box, refer to the MRB3 manual.
5. M3 Washers x 2
4. M3 x 20mm Screws x2 6. M3 Hex Nuts x 2
3. #7 x 1.25 Kit Screws x4
X3-DM3
A
D
C C C
B
E
A. Remove the factory rocker switches.
D. Place the base plate back on the dash lining up the outside
screw holes to the dimples on the dash. Using (2) #7 Screws and
a philips screw driver secure the base to the dash. Make sure the
screws are driving into the dash dimples for best results.
Line up base plate Drill pilot hole Drill 1/2” hole
C. Rest the X3-DM3 base plate on the dash. Line up the two outside screw holes with the dimples of the dash. Do not screw the kit in yet.
While holding the base plate down to the dash, use the center hole on the base plate to drill your 1/8” pilot hole.
Remove the base plate and open the pilot hole up using a 1/2” drill bit.
B. Locate the two dimples at the top of the dash. These dimples
are actual screw bosses on the underside of the dash.
E. Fasten the MRB3 Remote to the dash kit using (2) M3 screws.

Produkt Specifikationer

Mærke: SSV Works
Kategori: Ikke kategoriseret
Model: X3-DM3

Har du brug for hjælp?

Hvis du har brug for hjælp til SSV Works X3-DM3 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret SSV Works Manualer

SSV Works

SSV Works BR-DS10U Manual

1 Januar 2025
SSV Works

SSV Works RZ4-2KRC Manual

24 August 2024
SSV Works

SSV Works RZ3-DM3 Manual

24 August 2024
SSV Works

SSV Works WP3-RZOA Manual

24 August 2024
SSV Works

SSV Works GN-5A Manual

24 August 2024
SSV Works

SSV Works CM-DM3 Manual

24 August 2024
SSV Works

SSV Works RZ3-3A Manual

24 August 2024
SSV Works

SSV Works RG4-5KRC Manual

24 August 2024
SSV Works

SSV Works RG4-DM3 Manual

24 August 2024
SSV Works

SSV Works X3-DM3 Manual

24 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Synology

Synology CMA-01 Manual

1 August 2025
Synology

Synology RKS-02 Manual

1 August 2025
Navman

Navman MiVue 765 SAFETY Manual

1 August 2025
Navman

Navman MY75T Manual

1 August 2025
Exquisit

Exquisit AIRFRY 3010 Manual

1 August 2025
Navman

Navman MiVue 155 SAFETY Manual

1 August 2025
Navman

Navman MiVue 698 Manual

1 August 2025
Newland

Newland FM550 Manual

1 August 2025
Tripp Lite

Tripp Lite SRIN4181810 Manual

1 August 2025
Navman

Navman MyTruck III Manual

1 August 2025